Search results for "Heating"

Microscopic evidence of a flat melting curve of tantalum

2010

International audience; New data on the high-pressure melting curve of Ta up to 48GPa are reported. Evidence of melting from changes in sample texture was found in five different experiments using scanning electron microscopy. The obtained melting temperatures are in excellent agreement with earlier measurements using x-ray diffraction or the laser-speckled method but are in contrast with several theoretical calculations. The results are also compared with shock-wave data. These findings are of geophysical relevance because they confirm the validity of earlier experimental techniques that resulted in low melting slopes of the transition metals measured in the diamond-anvil cell, including i…

Modelling of a prosumer’s substation in a district heating network: validation and dynamic analysis

Thermal grids will play a key role in the development of local energy communities and the achievement of 100% renewable societies. However, challenges are related to the capability of dealing with the increasing number of producers which could supply heat to thermal grids. Indeed, as in the case of the electricity grid, heat could be available for some hours in a day from RES plants installed at user level and distributed in the network (also referred to as “prosumers”). To achieve more reliable results when performing energy analyses of these innovative applications, there is a need to rely on accurate models of each component. For instance, substations are of paramount importance in the i…

Automatic detection of thermal anomalies in induction motors

2021

The paper proposes a methodology based on Artificial Intelligence techniques for the automatic detection of abnormal thermal distributions in electric motors, to rapidly identify pre-faults or fault conditions. The proposed approach, applied to induction motors of different sizes, installed in waterworks plants, is based on the execution of Thermographic Non-Destructive Tests, which allow identifying abnormal operating conditions without interrupting the ordinary working conditions of the system. Thermographic images of induction motors are acquired at the installation site and with perspectives visible to the operator, which are sometimes partially obstructed. These thermographic images ar…

Analytical RF Pulse Heating Analysis for High Gradient Accelerating Structures

2021

The main aim of this work is to present a simple method, based on analytical expressions, for obtaining the temperature increase due to the Joule effect inside the metallic walls of an RF accelerating component. This technique relies on solving the 1-D heat-transfer equation for a thick wall, considering that the heat sources inside the wall are the ohmic losses produced by the RF electromagnetic fields penetrating the metal with finite electrical conductivity. Furthermore, it is discussed how the theoretical expressions of this method can be applied to obtain an approximation to the temperature increase in realistic 3-D RF accelerating structures, taking as an example the cavity of an RF e…

A novel renewable polygeneration system for a small Mediterranean volcanic island for the combined production of energy and water: Dynamic simulation…

2014

Abstract This paper investigates the integration of solar and geothermal energy in a novel polygeneration system producing simultaneously: electricity, thermal energy, cooling energy and fresh water. The polygeneration system under analysis includes concentrating photovoltaic/thermal solar collectors (CPVT), a Geothermal Well (GW) a multi-effect distillation (MED) system for seawater desalination, a single-stage LiBr–H2O absorption chiller and additional components, such as: storage tanks, heat exchangers and balance of plant devices. The CPVT produces simultaneously electrical energy and thermal energy, at a maximum temperature of about 100 °C. The electrical energy is delivered to the gri…

Numerical Assessment of Heating Energy Demand for Office Buildings in Italy

2016

Abstract Buildings energy consumption depends on several parameters, such as climate, envelope typologies, occupant behavior, intended use, etc.; assessment of the energy performance of a building requires substantial input data describing constructions, environmental contexts, thermo-physical properties, geometry, control strategies and several other parameters influencing the thermal balance. In the last years, several numerical approaches dedicated to building simulation have been tested developing specialized software. On the other hand, simplified building models permit the evaluation of indoor conditions and heating/cooling loads with a good level of accuracy and without excessive com…

Assessing the feasibility of cogeneration retrofit and district heating/cooling networks in small Italian islands

2017

Sustainability of energy supply strategies in small islands has been emerging as a severe issue, due to the large margins for improvement and rationalization of the most frequently adopted solutions. In most of the European islands, large amounts of heat are wasted by the operation of engine-based power plants; conversely, heat is produced by boilers (supplied by liquid fuels) or by electric equipment for a number of different uses, like domestic hot water production or space heating in winter. In this paper a techno-economic analysis is proposed to assess the feasibility of CHP-retrofit of the existing power plants and the possible utilization of the recovered heat to supply, via a distric…

PCM thermal storage design in buildings: Experimental studies and applications to solaria in cold climates

2017

Abstract As energy availability and demand often do not match, thermal energy storage plays a crucial role to take advantage of solar radiation in buildings: in particular, latent heat storage via phase-change material is particularly attractive due to its ability to provide high energy storage density. This paper analyzes the performance of a building-integrated thermal storage system to increase the energy performances of solaria in a cold climate. A wall opposing a highly glazed facade (south oriented) is used as thermal storage with phase change materials embedded in the wall. The study is based on both experimental and simulation studies. The concept considered is particularly suited t…

Numerical studies of the melting process in the induction furnace with cold crucible

2008

PurposeAims to present recent activities in numerical modeling of cold crucible melting process.Design/methodology/approach3D numerical analysis was used for electromagnetic problem and 3D large eddy simulation (LES) method was applied for fluid flow modeling.FindingsThe comparative modeling shows, that higher H/D ratio of the melt is more efficient when total power consumption is considered, but this advantage is held back by higher heat losses through the crucible walls. Also, calculations reveal that lower frequencies, which are energetically less effective, provide better mixing of the melt.Originality/value3D electromagnetic model, which allows to take into account non‐symmetrical dist…

25-kW/50-kHz generator for induction heating

1991

The authors present the features, technology, and construction of a transistorized generator for induction heating operating over the 4-50 kHz frequency range. This type of 25 kW output-power generator allows replacement of the electronic tube generators for most of their applications. The advantages of this new generator are more energy efficiency, extended life, reduced size, separated heating station of the generator, and connection by flexible cable. In addition, the generator has incorporated a frequency automatic tracking system that allows operating without any adjustments over a wide frequency range. >