Search results for "Low-power"
showing 10 items of 10 documents
Adapting power consumption to performance requirements in a MSP430 microcontroller
2005
Microcontroller based low power systems using batteries must run at low clock frequencies with short activity periods to extend battery life. These constraints reduce the microcontroller computational capabilities and limit the complexity of algorithms that can be used. New microcontroller architectures, as the Texas Instruments MSP430 family, allow to adapt power consumption to application performance requirements combining several low power modes with the capability of switching the clock frequency dynamically. A complete characterization of power consumption vs. performance has been obtained for the MSP430. A method to determine the range of clock frequencies that meets a consumption and…
A Low-Power Fully-Mosfet Voltage Reference Generator for 90 nm CMOS Technology
2006
An integrated voltage reference generator, designed for being incorporated in standard 90-nm CMOS technology flash memories, is described in this paper. A fully MOSFET based approach, using also subthreshold operated devices, has been adopted in order to achieve low-voltage and low-power requirements and to overcome the difficulties of conventional band-gap reference circuits. The proposed circuit, based on current signals, internally generates two currents with opposite dependence on temperature. The two currents are added, thus canceling almost completely temperature dependence, and then linearly converted into the output voltage. For a temperature variation between -20degC and 90degC, th…
A Methodology for the Design of MOS Current-Mode Logic Circuits
2010
In this paper, a design methodology for the minimization of various performance metrics of MOS Current-Mode Logic (MCML) circuits is described. In particular, it allows to minimize the delay under a given power consumption, the power consumption under a given delay and the power-delay product. Design solutions can be evaluated graphically or by simple and effective automatic procedures implemented within the MATLAB environment. The methodology exploits the novel concepts of crossing-point current and crossing-point capacitance. A useful feature of it is that it provides the designer with useful insights into the dependence of the performance metrics on design variables and fan-out capacitan…
Low-Power Design of Delay Interpolating VCO
2008
In this paper, a design methodology for low-power MCML based delay interpolating VCOs is presented. The methodology allows a fast and accurate graphical evaluation of the optimum design. It utilizes two closed form expressions for the upper and lower oscillation frequencies of the VCO. An expression of the tuning range is also derived. The effectiveness of the proposed design methodology has been tested by simulating several VCOs in an IBM 0.13 mum CMOS technology.
Quasi-static magnetoresistive sensor modeling for current-time conversion circuit applications
2011
In this paper we report a current-to-time converter (CTC) suitable for current sensor monitoring in low power applications. Based on a discrete resistence-to-frequency converter and a Giant MagnetoResistance (GMR) current sensor. Simulations have been done using a quasi-static electrical Verilog-A model for the GMR current sensor. A reduced set of parameters has been extracted to characterize the GMR sensor's behavior. The application has been analyzed making use of different sensors, whose device parameters were previously extracted. Finally, the accuracy of the models has been tested by comparing with experimental transient measurements.
Quasi‐digital front‐ends for current measurement in integrated circuits with giant magnetoresistance technology
2014
In this study, the authors report on two different electronic interfaces for low-power integrated circuits electric current monitoring through current-to-frequency (I-f) conversion schemes. This proposal displays the intrinsic advantages of the quasi-digital systems regarding direct interfacing and self-calibrating capabilities. In addition, as current-sensing devices, they have made use of the giant magnetoresistance (GMR) technology because of its high sensitivity and compatibility with standard complementary metal oxide semiconductor processes. Single elements and Wheatstone bridges based on spin-valves and magnetic tunnel junctions have been considered. In this sense, schematic-level si…
The CZT X-ray imager on AXO
2001
DSRI has initiated a development program of CZT X-ray and gamma ray detectors employing strip readout techniques. A dramatic improvement of the energy response was found operating the detectors as so-called drift detectors. For the electronic readout, modern ASIC chips were investigated. Modular design and the low power electronics will make large area detectors using the drift strip method feasible. The performance of a prototype CZT system will be presented and discussed. One such detector system has been proposed for future space missions: The X-Ray Imager (XRI) on the Atmospheric X-ray Observatory (AXO), which is a mission proposed to the Danish Small Satellite Program and is dedicated …
Note: Direct sensor resistance-to-frequency conversion with generalized impedance converter.
2010
In this note a squared output signal is generated from an astable circuit. Its frequency has a linear dependence on the resistance value of a resistive temperature sensor. The main circuit to obtain this direct relationship is the generalized impedance converter configured as a capacitor controlled by a sensor resistance. The proposed measurement method allows a direct analog-to-digital interface of information involved in resistive sensors. The converter finds applications in portable low voltage and low power design of instrumentation electronic systems.
A Design Methodology for Low-Power MCML Ring Oscillators
2007
In this paper, a low-power design method for MCML based ring oscillators is presented. The proposed method takes into account the parasitic capacitances of the MOS transistors. To validate it, some ring oscillators with different oscillation frequencies were designed in a 0.18 mum CMOS technology. SPICE simulations demonstrate the effectiveness of the design method.
Preamble Sampling MAC Protocol for Low Power Wireless Sensor Networks with IEEE 802.15.4 Transceivers
2006
In this paper a preamble sampling MAC protocol for low power wireless sensor networks is proposed. The article describes the implementation of the protocol using network nodes equipped with the Chipcon CC2420 802.15.4 transceiver. The power consumption of the transceiver has been measured and the MAC protocol has been adapted to the transceiver properties. The results show the trade-off between power consumption and transmission delay for this algorithm during the communication process.