Search results for "MICROSTRUCTURE"
showing 10 items of 707 documents
Tuning four-wave mixing through temperature in ethanol-filled photonic crystal fiber
2016
In this paper, continuous tuning of four-wave mixing bands in an ethanol-filled photonic crystal fiber is investigated. A wide tuning range of the parametric bands, from 745 nm to 920 nm (signal) and from 1260 nm to 1710 nm (idler), is achieved through the thermo-optic effect. This corresponds to a frequency tuning range higher than 2000 cm−1; such wide range can be particularly useful in applications that require broadband wavelength conversion, e.g., CARS microscopy. Numerical calculations are in good agreement with experimental measurements.
Influence of Heat Treatment on Fatigue Crack Growth in Ti-6Al-4V Alloy
2011
The paper contains the results of experimental work carried out in order to analyse the initiation and propagation of fatigue cracks in Ti-6Al-4V titanium alloy. The tests were performed on plane specimens with the stress concentrators in form of one-sided sharp notches. The tested specimens were made of the oxygenated Ti-6Al-4V subjected to various variants of heat treatment.
Structure, nanohardness and photoluminescence of ZnO ceramics based on nanopowders
2015
ZnO ceramics obtained from grained powders with different grain size by hot pressing and ceramics from tetrapods nanopowders obtained by press-less sintering have been investigated under identical conditions. Ceramics obtained by hot pressing were optically transparent but were composed of large inhomogeneous grains (d = 8–35 μm) exhibiting a substructure. Decreased values of elastic modulus within a grain and a wide defect-associated ('green') photoluminescence (PL) band at 2.2–2.8 eV in conjunction with a weak excitonic band indicate a high concentration of residual point defects in hot pressed ZnO ceramics. Utilization of more small-grained powders contributes to the formation of more un…
Femtosecond pulse compression in a hollow-core photonic bandgap fiber by tuning its cross section
2012
Abstract We present a numerical study of soliton pulse compression in a seven-cell hollow-core photonic bandgap fiber. We analyze the enhancement of both the compression factor and the pulse shape quality of 360 nJ femtosecond pulses at the wavelength of 800 nm by tuning the cross section size of the fiber. We use the generalized non-linear Schrodinger equation in order to modeled the propagation of light pulses along the fiber. Our numerical results show that output compressed pulses can be obtained, in a propagation length of 31 cm, with a compression factor of 5.7 and pulse shape quality of 77% for a reduction of 4.5% of the cross section size of the fiber. The predicted compression fact…
Predicting stiffness and strength of birch pulp:Polylactic acid composites
2016
This paper studies failure of birch pulp–polylactic acid composites. Stiffness and strength are calculated using the theory of short fibre composites and the results are compared to experimental data. The results differed from the experimental values by 0–6%. With less aligned fibres the short fibre theory is not feasible. The performance of the 40 wt% birch pulp – polylactic acid composite is predicted with X-ray microtomography based finite element modelling, and the results are compared with experiments. Stiffness results differed from experiments by 1–17% . By adding into the models a third material phase representing the interface between the fibres and the matrix, the stress–strain c…
Micro - Architectural Data Extraction for Electrospun Poly (Ester Urethane) Urea Scaffolds for Biomechanical Modeling.
2009
Problem: Soft tissue engineered applications have raised the need for accurate descriptions of tissue microstructure and their contributions to global mechanical behavior [1]. Accurate material image analysis is crucial to model engineered tissue biomechanics. The present study proposes a novel method to automatically collect micro-architectural data from electron micrographs (SEM) of electrospun poly (ester urethane) urea (PEUU). Methods: Sets of contiguous SEM images for electrospun PEUU scaffolds made using three mandrel collection tangential velocities (1.5, 4.5, 9.0 m/s) were analyzed. A combination of thresholding and morphological procedures enabled overlaps of fibers to be detected.…
Droplet cell investigation of intergranular corrosion on AA2024
2017
An original method combining a droplet cell with direct optical interrogation of the reverse side of a 50μm thick foil AA2024 has been tested to evaluate the possible analysis of the current during intergranular corrosion tests. The foil microstructure and the selected orientation were suitable for recording the current generated during the propagation in volume of a well-defined grain boundary trace. Even if it is impossible to reach a charge and mass balance from these preliminary attempts, it was demonstrated that it is possible, despite hydrogen evolution, to record a current transient resulting from the full penetration of an intergranular path. Keywords: Intergranular corrosion, Alumi…
The role of yttrium and titanium during the development of ODS ferritic steels obtained through the STARS route: TEM and XAS study
2018
Abstract Oxide Dispersion Strengthened Ferritic Steels (ODS FS) are candidate materials for structural components in future fusion reactors. Their high strength and creep resistance at elevated temperatures and their good resistance to neutron radiation damage is obtained through extremely fine microstructures containing a high density of nanometric precipitates, generally yttrium and titanium oxides. This work shows transmission electron microscopy (TEM) and extended X-ray absorption fine structure (EXAFS) characterization of Fe-14Cr-2W-0.3Ti-0.24Y ODS FS obtained by the STARS route (Surface Treatment of gas Atomized powder followed by Reactive Synthesis), an alternative method to obtain O…
Synthesis and catalytic performance in ethylene and 1-octene polymerization of chlorotitanium(IV) silsesquioxane complexes. Effect of increasing liga…
2016
Abstract The series of titanasilsesquioxanes that differ in a way of binding to the transition metal ( via one, two or three oxygen atoms) and type of nonreactive substituents bonded to inorganic oxygen-silicon cage ( i -Bu, Ph, c -C 6 H 11 ) were prepared by reacting of TiCl 4 with 1 eqv. of the silsesquioxane ligand. Upon treatment with an appropriate cocatalyst, all titanium precatalysts are active in ethylene and 1-octene polymerization and produce from low to high molecular weight polyethylenes and moderately ([ mmmm ] = 44–74%) isotactic poly(1-octene)s. The influence of polymerization parameters, type of cocatalyst and the silsesquioxane structure on the catalytic behavior of the tit…
Experimental Comparison of the MIG and Friction Stir Welding Processes for AA 6005 Aluminium Alloy
2015
In this study, the mechanical properties of welded joints of AA 6005 aluminum alloy obtained with friction stir welding (FSW) and conventional metal inert gas welding (MIG) are studied. FSW welds were carried out on a semi-automatic milling machine. The performance of FSW and MIG welded joints were identified using tensile and bending impact tests, as far as the environmental aspects are also included in the discussion. The joints obtained with FSW and MIG processes were also investigated in their microstructure. The results indicate that, the microstructure of the friction stir weld is different from that of MIG welded joint. The weld nugget consists of small grains in FSW than those found…