Search results for "Magnesium"

Tuning of the Mg Alloy AZ31 Anodizing Process for Biodegradable Implants

2021

Coatings were grown on the AZ31 Mg alloy by a hard anodizing process in the hot glycerol phosphate-containing electrolyte. Anodizing conditions were optimized, maximizing corrosion resistance estimated by impedance measurements carried out in Hank's solution at 37 °C. A post anodizing annealing treatment (350 °C for 24 h) allowed us to further enhance the corrosion resistance of the coatings mainly containing magnesium phosphate according to energy-dispersive X-ray spectroscopy and Raman analyses. Gravimetric measurements revealed a hydrogen evolution rate within the limits acceptable for application of AZ31 in biomedical devices. In vitro tests demonstrated that the coatings are biocompati…

Positron annihilation studies of recrystallization in the subsurface zone induced by friction in magnesium—effect of the inhomogeneity on measured po…

2013

The discussion of the positron annihilation studies of crystal structure defects, like vacancies, dislocations, grain boundaries and the defect depth profile, is presented. The role of the positron implantation depth and positron diffusion in such studies has been considered in detail. For description of the measured annihilation characteristics the proposed theoretical models take into account both effects. The annealing studies of defects created in pure magnesium by compression or dry sliding-wear were used for demonstration of the discussed thesis. The positron lifetime measurements were applied for monitoring open volume defects behavior. It was demonstrated that annealing at the tempe…

Study of inversion domain pyramids formed during the GaN:Mg growth

2003

AbstractThestudyofstructuraldefectsinducedbytheintroductionofMgduringthegrowthofMOCVDGaNispresented.Themagnesiumincorporationintothecrystalgrowthnotonlyinduceschangesinthestackingsequencefromhex-agonaltocubicstructures,butalsoinvertstheGaNpolarityfromGa-facetoN-face.Basedonthedifferentsurfacestructureandsurfacemigrationlengthofabsorbingprecursorsforeachpolaritytype(Ga-orN-face),the3DgrowthontopoftheN-facetriangulardefectisdescribed.TheN-facematerialischaracterizedbythreedanglingbondsofni-trogenthatpointuptowardthec-planesurface,enhancingthecrystalgrowthalongthec-axis. 2002ElsevierScienceLtd.Allrightsreserved. Keywords:Inversiondomain;Stackingfault;Polarity 1. IntroductionFurther progress tow…

Friction Stir Welding of Magnesium Alloys under Different Process Parameters

2010

Experimental and numerical investigations have been performed in order to study the effect of welding parameters on properties of FSW-ed AZ31 magnesium alloy sheets. The results, presented in terms of tensile strength and numerical field variables distributions, allow to understand the behaviour of such material when FSW-ed using different rotational and welding speeds for a given tool geometry.

Friction stir welding of dissimilar aluminium– magnesium joints: Sheet mutual position effects

2015

Friction stir welding (FSW) is a solid state welding process used to weld difficult to be welded or unweldable materials as aluminium alloys. In the last years, other materials have been successfully tested as magnesium, titanium and nickel based alloys. Dissimilar joints can be obtained by FSW, but issues arise concerning the correct choice of the process parameters. In the paper, the results of an experimental and numerical campaign aimed to produce dissimilar AZ31-AA6016-T6 butt joints are presented. The effect of sheet mutual position and main process parameters was investigated. It was found that intermetallics are the main cause of the poor quality of the joints. Sound joints can be p…

The use of microcapillary techniques to study the corrosion resistance of AZ91 magnesium alloy at the microscale

2011

Abstract The AZ91 alloy is composed of Mg 17 (Al, Zn) 12 precipitates, an eutectic phase around these precipitates, AlMn intermetallic particles and an α-Mg solid solution (matrix). The corrosion behaviour of AZ91 was investigated at the microscale by means of the electrochemical microcell technique, which uses extremely small capillaries (diameters between 5 and 10 μm). Experiments were conducted in 0.1 M NaClO 4 at 25 °C. The β-Mg 17 (Al, Zn) 12 precipitates were found to have the highest corrosion resistance, whereas the eutectic phase was very active (pitting potential of approximately −1400 mV vs. Ag/AgCl). The α-Mg solid solution displayed better corrosion resistance than the eutectic…

Dopant radial inhomogeneity in Mg-doped GaN nanowires

2018

International audience; Using atom probe tomography, it is demonstrated that Mg doping of GaN nanowires grown by Molecular Beam Epitaxy results in a marked radial inhomogeneity, namely a higher Mg content in the periphery of the nanowires. This spatial inhomogeneity is attributed to a preferential incorporation of Mg through the m-plane sidewalls of nanowires and is related to the formation of a Mg-rich surface which is stabilized by hydrogen. This is further supported by Raman spectroscopy experiments which give evidence of Mg-H complexes in the doped nanowires. A Mg doping mechanism such as this, specific to nanowires, may lead to higher levels of Mg doping than in layers, boosting the po…

Dielectric properties of PMN+2%Li 2 O at low frequencies

2012

The reported study is focused on effects of the admixture of lithium (2% Li2O) on the low-frequency dielectric response in lead magnesium niobate ceramics over the 100 -300 K range of temperature. The obtained results reveal an essential thermal broadening of the e′(ν) spectra specific to relaxor ferroelectrics. Dispersion Δe′ = e′1Hz-e′1kHz and values of e′′(ν) in lead magnesium niobate ceramics containing Li are well described by the Cole-Cole equation at temperatures below the e′(T) maximum. Based on the analysis of the experimental data admixture of lithium is suggested to promote formation of domains in lead magnesium niobate ceramics (© 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim)

2018

Abstract When electrochemical techniques are used to probe the surface of corroding magnesium with the aim of obtaining quantitative information on the corrosion process, two peculiarities are generally observed: i) with anodic polarization, the rate of hydrogen evolution increases instead of decreasing and ii) during electrochemical impedance spectroscopy measurements, an inductive contribution is often observed at the low-frequency end of the spectra. The presence of these two phenomena clearly has an impact on the methodology that should be applied to correctly estimate corrosion rates from electrochemical data. The aim of this work is to provide a general mathematical description of the…

Application of Positron Annihilation Spectroscopy to Studies of Subsurface Zones Induced by Wear in Magnesium and Its Alloy AZ31

2011

Interaction of sliding bodies is an important aspect of numerous applications and subject of many studies (Solecki, 1989). Generally, when two surfaces are loaded together the true contact area is much smaller than the apparent one. The true contact is only at high points or asperities of the surfaces where the interactions in the atomic scale take place. Relative movement between the surfaces leads to friction and wear processes. The rate of wear is controlled by the load, the relative velocity and the behaviour of the material near asperities. The region of asperities can be plastically deformed and the stress is transported to the deeper laying region that becomes elastically deformed (F…