Search results for "Mechanics of Material"
showing 10 items of 2608 documents
Influence of initial treatments of aluminium on the morphological features of electrochemically formed alumina membranes
2003
Abstract The fabrication of alumina membranes by electrochemical oxidation of annealed aluminium was investigated. Porous layers were grown in 0.4 M H3PO4 at −1 and 5 °C at different anodising times. The morphology of the outer surface was found to be dependent on temperature and charge density, with both determining the extent of chemical dissolution of the anodic oxide. The inner-surface morphology was found to depend on the applied voltage only. The chemical dissolution rate of anodic oxide grown on annealed aluminium was found to be lower than that formed on unannealed aluminium under otherwise identical conditions. Such a difference in behaviour is explained in terms of a higher finish…
Co-precipitation synthesis of Nd:YAG nano-powders: the effect of Nd dopant addition with thermal treatment
2007
Nanopowders of Yttrium Aluminium Garnet doped with neodymium ions were obtained by the co-precipitation method from the reaction of aluminium, yttrium and neodymium nitrate with ammonia. The amount of neodymium was selected in order to produce samples of nominal stoichiometry NdXY (3-X)Al5O12 (where X = 0.006, 0.012, 0.024, 0.048, 0.081, 0.096, 0.17, 0.19, 0.38, 0.54, and 0.72, respectively). After washing and drying, the hydroxide precursors were subjected to Thermo-Gravimetry and Differential Thermal Analysis experiments from room temperature up to 1500 °C, which showed the presence of exothermal events accompanying phase transformation phenomena. X-ray diffraction investigations conducte…
Effect of NiO and/or TiO2 mullite formation and microstructure from gels
1998
Polymeric and colloidal gels with a constant molar ratio of (Al+Ni and/or Ti)/Si=3/1 and various (Al/Ni and/or Ti) ratios (up to 21.42 mol% NiO+TiO2) were prepared and used to study the effect of the precursor chemical homogeneity on mullite formation processes and the resulting microstructure. Both kinds of gel precursors were preheated at 750°C for 3 h in order to obtain appropriate gel-derived glasses for further thermal processing. After annealing for several time periods at temperatures between 750 and 1500°C, differences in crystallization pathways were observed. Polymeric gels crystallized Al–Si and NiAl2O4 spinels from the amorphous form at temperatures in the range between 900 and …
Shear coefficient determination in linear friction welding of aluminum alloys
2015
In the present study, a combined experimental and numerical investigation on Linear Friction Welding (LFW) of AA2011-T3 aluminum alloy was carried out in order to find the temperature dependent shear coefficient to be used in a 3D numerical model of the process. Torque, oscillation frequency and pressure were acquired in order to calculate the shear stress at the interface. A numerical thermal model was used to calculate the temperature at the interface between the specimens starting from experimental temperatures acquired through a thermocouple embedded in the LFW specimens. Finally, the calculated shear coefficient was used to model the contact between the two specimens in a dedicated 3D,…
Selective adsorption of oppositely charged PNIPAAM on halloysite surfaces: a route to thermo-responsive nanocarriers.
2018
Halloysite nanotubes were functionalized with stimuli-responsive macromolecules to generate smart nanohybrids. Poly(N-isopropylacrylamide)-co-methacrylic acid (PNIPAAM-co-MA) was selectively adsorbed into halloysite lumen by exploiting electrostatic interactions. Amine-terminated PNIPAAM polymer was also investigated that selectively interacts with the outer surface of the nanotubes. The adsorption site has a profound effect on the thermodynamic behavior and therefore temperature responsive features of the hybrid material. The drug release kinetics was investigated by using diclofenac as a non-steroidal anti-inflammatory drug model. The release kinetics depends on the nanoarchitecture of th…
Synthesis of Peroxyapatite by Hydrothermal Processing
2014
Peroxide ions in apatite provides an additional resource for imparting an antibacterial capability in apatite. A hydrothermal process has been developed for including peroxide ions into the apatite lattice. Three oxygen generation compounds, hydrogen peroxide, ammonium persulphate and paracetic acid were investigated for peroxyapatite generation. Hydrogen peroxide provides the highest peroxide containing apatite. Both the oxygen generation and the apatite lattice formation represented the two critical factors for producing peroxyapatite. Unlike with high temperature processing, the cooling rate did not influence the retained peroxide content. This new process provides a building block for i…
Magnetic and structural study of (Fe1−Co )62 Nb8B30 bulk amorphous alloys
2004
Abstract The electric and magnetic properties of rapidly quenched (Fe 1− x Co x ) 62 Nb 8 B 30 bulk metallic glasses were studied with x =0, 0.33 and 0.50. The Curie temperature in the amorphous state was found to be about 245 °C for the Co-free alloy, 290 °C for x =0.33 and 201 °C for x =0.50, while the crystallization temperature is varying within 15° only around 600 °C. The change in T C correlates with the change in Mossbauer parameters. An interesting flattening effect of annealing on the hysteresis loop was observed which increases with the Co content. The resistivity could not be improved above 152 μΩ cm, which limits the high frequency applications of these alloys.
Three-dimensional photonic crystal intermediate reflectors for enhanced light-trapping in tandem solar cells
2011
A three-dimensional photonic crystal intermediate reflector for enhanced light trapping in tandem solar cells is presented. The intermediate reflector consists of a transparent and conductive ZnO:Al inverted opal sandwiched in between the top amorphous silicon and bottom microcrystalline silicon cell.
Electroluminescence and transport properties in amorphous silicon nanostructures
2006
We report the results of a detailed study on the structural, electrical and optical properties of light emitting devices based on amorphous Si nanostructures. Amorphous nanostructures may constitute an interesting system for the monolithic integration of optical and electrical functions in Si ULSI technology. In fact, they exhibit an intense room temperature electroluminescence (EL), with the advantage of being formed at a temperature of 900 °C, while at least 1100 °C is needed for the formation of Si nanocrystals. Optical and electrical properties of amorphous Si nanocluster devices have been studied in the temperature range between 30 and 300 K. The EL is seen to have a bell-shaped trend …
Immobilization of functionalized lipids in a random poly(methacrylate) copolymer monolayer
1995
It is shown that a monolayer of random poly(methacrylate) copolymer with a hydrophobic and a hydrophilic substituent exhibits a transition from the fluid to amorphous state. Above this transition any amphiphilic molecules mixed with the monolayer are immobile. Furthermore, such functionalized lipids are immobilized in the monolayer during the Langmuir-Blodgett transfer. The hydrophilic head-groups of the biotin-lipids remain on the formerly water-adjacent side of the monolayer, even if this side is exposed to air