Search results for "Metallurgy"

Structural and optical characterization of ZnS ultrathin films prepared by low-temperature ALD from diethylzinc and 1.5-pentanedithiol after various …

2019

The structural and optical evolution of the ZnS thin films prepared by atomic layer deposition (ALD) from the diethylzinc (DEZ) and 1,5-pentanedithiol (PDT) as zinc and sulfur precursors was studied. A deposited ZnS layer (of about 60 nm) is amorphous, with a significant S excess. After annealing, the stoichiometry improved for annealing temperatures &ge

Mechanical and optical properties of as-grown and thermally annealed titanium dioxide from titanium tetrachloride and water by atomic layer deposition

2021

Funding Information: This work was carried out within the MECHALD project funded by Business Finland (Tekes) and is linked to the Finnish Centers of Excellence in Atomic Layer Deposition (ref. 251220) and Nuclear and Accelerator Based Physics (refs. 213503 and 251353) of the Academy of Finland. Funding Information: This work was carried out within the MECHALD project funded by Business Finland (Tekes) and is linked to the Finnish Centers of Excellence in Atomic Layer Deposition (ref. 251220 ) and Nuclear and Accelerator Based Physics (refs. 213503 and 251353 ) of the Academy of Finland. Publisher Copyright: © 2021 The use of thin-films made by atomic layer deposition (ALD) is increasing in …

On the high-pressure phase stability and elastic properties ofβ-titanium alloys

2017

We have studied the compressibility and stability of different β-titanium alloys at high pressure, including binary Ti–Mo, Ti–24Nb–4Zr–8Sn (Ti2448) and Ti–36Nb–2Ta–0.3O (gum metal). We observed stability of the β phase in these alloys to 40 GPa, well into the ω phase region in the P–T diagram of pure titanium. Gum metal was pressurised above 70 GPa and forms a phase with a crystal structure similar to the η phase of pure Ti. The bulk moduli determined for the different alloys range from 97  ±  3 GPa (Ti2448) to 124  ±  6 GPa (Ti–16.8Mo–0.13O).

Removal of silicon from CFB-derived fly ash leachate in the context of phosphorus recovery

2018

High concentrations of dissolved silica in the acid leachate impose two major challenges on precipitation based recovery of phosphorus (P). Firstly, co-precipitation of colloidal silica in the acidic regimes decreases the purity and value of precipitated P-products. In addition, silica scaling on internal surfaces of equipment is also a problematic issue in industrial operations. Therefore, removal of dissolved silica prior to P-recovery process minimizes the risks of Si-contamination in P-products and Si-scaling. In the present study, silica removal was achieved by accelerated silica polymerization with higher acidity and ionic strength of mineral acid, which also assisted the leaching of …

Microscratch testing method for systematic evaluation of the adhesion of atomic layer deposited thin films on silicon

2016

The scratch test method is widely used for adhesion evaluation of thin films and coatings. Usual critical load criteria designed for scratch testing of coatings were not applicable to thin atomic layer deposition (ALD) films on silicon wafers. Thus, the bases for critical load evaluation were established and the critical loads suitable for ALD coating adhesion evaluation on silicon wafers were determined in this paper as LCSi1, LCSi2, LCALD1, and LCALD2, representing the failure points of the silicon substrate and the coating delamination points of the ALD coating. The adhesion performance of the ALD Al2O3, TiO2, TiN, and TaCN+Ru coatings with a thickness range between 20 and 600 nm and dep…

Influence of the microstructure on the durability of hard coatings obtained from metal powders

2016

Influence of the process parameters on the microstructure of a hardfacing coating elaborated by hot isostatic pressing

2019

Hot Isostatic Pressing elaboration of Norem02, an austenitic-ferritic hypereutectoid stainless steel, leads to the formation ofan austenitic matrix with a mixture of acicular M7C 3 and globular M23 C 6 carbides. The sintering tests, carried out by using an AISI304L container, showed that the final microstructure and the carbides’ distribution of the HIPed Norem02 are strongly influencedby the process parameters (heating and cooling rate, sintering time, holding temperature and pressure) and by the particles’ size,microstructure and phase distribution of the initial powder. The morphological, crystallographic and chemical analysis of the sinteredsamples were completed by comprehension of the…

Comparison of Post-Weld Treatment of High-Strength Steel Welded Joints in Medium Cycle Fatigue

2010

This paper presents a comparison of three post-weld treatments for fatigue life improvement of welded joints. The objective is to determine the most suitable post-weld treatment for implementation in mass production of certain crane components manufactured from very high-strength steel. The processes investigated are: burr grinding, TIG dressing and ultrasonic impact treatment. The focus of this investigation is on the so-called medium cycle area, i.e. 10 000-500 000 cycles and very high stress ranges. In this area of fatigue design, the use of very high strength steel becomes necessary, since the stress range can exceed the yield-strength of ordinary structural steel, especially when consi…

Effect of Hot Dip Galvanized Steel Surface Chemistry and Morphology on Titanium Hexafluoride Pretreatment

2017

Titanium hexafluoride pretreatments are known to improve paint adhesion and function as a barrier between the coating and the hot dip galvanized (HDG) steel surface. Interactions at the zinc/pretreatment interface are of utmost importance for the formation of pretreatment layers and the corrosion resistance of color coated hot dip galvanized steels. Removal rate of inert aluminum oxide from HDG steel samples by chemical dissolution was studied. XPS measurements showed that the surface Al2O3 layer thickness decreased rapidly already at mild alkaline cleaning, while complete removal of Al required severe etching. Low reactivity of an Al2O3-rich surface was confirmed by impaired formation of a…

Charge Transport Mechanisms in Heavy-Ion Driven Leakage Current in Silicon Carbide Schottky Power Diodes

2016

Under heavy-ion exposure at sufficiently high reverse bias voltages silicon carbide (SiC) Schottky diodes are observed to exhibit gradual increases in leakage current with increasing ion fluence. Heavy-ion exposure alters the overall reverse current-voltage characteristics of these diodes, leaving the forward characteristics practically unchanged. This paper discusses the charge transport mechanisms in the heavy-ion damaged SiC Schottky diodes. A macro model, describing the reverse current-voltage characteristics in the degraded SiC Schottky diodes is proposed. peerReviewed