Search results for "NTR"
showing 10 items of 37262 documents
Pulsed Electro-Acoustic Method for specimens and cables employed in HVDC systems: Some feasibility considerations
2018
Recent experiments on the use of the PEA method for testing dielectric materials in specimens and comparison with a detailed model provide an insight of the phenomenon and suggest the need of adopting similar models also for cables. What is said is even more important considering the possible future adoption of the PEA methodology to test DC cables for Pre-Qualification and Type Tests. The use of an accurate model of the PEA cell used for testing specimens and related experiments prove that the thickness of the different parts composing the PEA setup is a basic element for providing accurate charge reading and interpretation of the phenomenon. Both simulation and experimental results, carri…
Guest Editorial
2019
Institute of Solid State Physics, University of Latvia as the Center of Excellence has received funding from the European Union’s Horizon 2020 Framework Programme H2020-WIDESPREAD-01-2016-2017-TeamingPhase2 under grant agreement No. 739508, project CAMART²
Experimental Equipment for Studying the Residual Stresses Developed During High Temperature Reactions by X-Ray Diffraction
1996
This paper describes a device dedicated to studyng, by X-ray diffraction the residual stresses developed on surface samples as a function of temperature and atmosphere conditions. The setup consists of : a.) an horizontal axis goniometer which allows the programmed positionning of the sealed X-ray source and of the linear detector. b.) a high temperature controlled atmosphere chamber Particular attention has been paid to the thermal stability up to 1200°C and the accurate position on the sample.
High quality epitaxial Mn 2 Au (001) thin films grown by molecular beam epitaxy
2020
The recently discovered phenomenon of Neel spin–orbit torque in antiferromagnetic Mn2Au [Bodnar et al., Nat. Commun. 9, 348 (2018); Meinert et al., Phys. Rev. Appl. 9, 064040 (2018); Bodnar et al., Phys. Rev. B 99, 140409(R) (2019)] has generated huge interest in this material for spintronics applications. In this paper, we report the preparation and characterization of high quality Mn2Au thin films by molecular beam epitaxy and compare them with magnetron sputtered samples. The films were characterized for their structural and morphological properties using reflective high-energy electron diffraction, x-ray diffraction, x-ray reflectometry, atomic force microscopy, and temperature dependen…
Effect of Cu doping on Ba0.95Pb0.05TiO3 electrical properties studied by means of electrical impedance spectroscopy
2019
The ceramics of 0.95BaTiO3–0.05PbTiO3+Xwt.%CuO (X = 0.05, 0.1, 1, 3) were prepared by a solid phase reaction. The structural and morphology studies were carried out by means of X-ray diffraction te...
Investigation and reduction of losses on inverter-fed induction motors
2017
An electric motor is more effective and flexible when supplied by a frequency converter. The frequency converter not only produces the fundamental voltage but also a set of higher harmonics which cause additional losses in the motor. Losses in the frequency converter are normally neglected in the drive dimensioning due to insufficient data available from manufacturers. Motor's losses can be reduced by increasing the switching frequency of frequency converters. An increase of the switching frequency may result in higher losses in the frequency converter. This work investigates analytically and experimentally the dependence of the losses of modern motor and frequency converter on a switching …
Identification of induction motor thermal model for improved drivetrain design
2016
Selection of components of electric drivetrains is not only based on evaluating their ability to perform according to mechanical specifications, but — what is equally important — on assessing their thermal protection limits. These are typically affected by electrical and thermal properties of motors and drives. Although rated parameters (such as power, torque, speed, etc.) are easily accessible in catalogs of equipment producers, more specific properties like mass / length of copper winding, heat dissipation factor, rotor / stator dimensions etc. are not available to customers. Therefore, effective selection of drivetrain components is limited due to the lack of sufficient data and the need…
A Magnetohydrodynamic Auxiliary Propulsion system for docking assistance of autonomous vehicle
2016
In this article we present an approach to the description of Magnetohydrodynamic Auxiliary Propulsion system for docking assistance of autonomous vehicle. Preliminarily, an analytical model which includes an electromagnetic model and a thermal model is presented. Successively, in order to move beyond the analytical model, a 3-D MHD modeling tool and a Runge Kutta method based solver are presented and they are used to investigate an alternative MHD solutions. Some numerical analysis are given
Sensorless control of induction motors using an extended Kalman filter and linear quadratic tracking
2017
Induction motors are the most commonly used prime-movers in industrial applications. Many induction motors supplied by frequency converters are coupled with a physical angular rotor position/velocity sensor which makes the drive complex and require maintenance. This paper presents a sensorless control structure to avoid using a physical angular rotor position/velocity sensor. The proposed method estimates and control the angular rotor velocity using optimal control theory. The optimal controller used in this paper is based on linear quadratic tracking and the states of the machine are estimated using an extended Kalman filter. Both the controller and the estimator utilize the same internal …
Multi-application Based Fault-Tolerant Network-on-Chip Design for Mesh Topology Using Reconfigurable Architecture
2019
In this paper, we propose a two-step fault-tolerant approach to address the faults occurred in cores. In the first stage, a Particle Swarm Optimization (PSO) based approach has been proposed for the fault-tolerant mapping of multiple applications on to the mesh based reconfigurable architecture by introducing spare cores and a heuristic has been proposed for the reconfiguration in the second stage. The proposed approach has been experimented by taking several benchmark applications into consideration. Communication cost comparisons have been carried out by taking the failed cores as user input and the experimental results show that our approach could get improvements in terms of communicati…