Search results for "NUMBER"
showing 10 items of 3939 documents
Synthesis, Characterization and Sorption Capacity Examination for a Novel Hydrogel Composite Based on Gellan Gum and Graphene Oxide (GG/GO)
2020
A novel hydrogel composite based on gellan gum and graphene oxide (GG/GO) was synthesized, characterized and tested for sorption capacity in this work. The microstructural, thermogravimetric and spectroscopic analysis confirmed the formation of the GG/GO composite. Comparative batch sorption experiments revealed a sorption capacity of the GG/GO composite for Zn (II) ions of approximately 2.3 higher than that of pure GG. The GG/GO composite exhibits a maximum sorption capacity of 272.57 mg/g at a pH of Zn (II) initial solution of 6. Generally, the sorption capacity of the sorbents is approximately 1.5 higher in slightly acidic conditions (pH 6) comparative with that for strong acidic conditi…
Three-dimensional analysis of load transfer micro-mechanisms in fibre/matrix composites
2009
International audience; This study gives a detailed analysis of load distributions around fibre breaks in a composite. In contrast to other studies reported in the literature, the analysis considers different configurations of composite damage from the failure of a few to the failure of many fibres. The model considers three types of matrix behaviours (elastic, elastic–plastic and viscoelastic) with or without debonding at the broken fibre/matrix interface. In this way, the usual limitations of the finite element approach are overcome so as to take into account the number and interactions of broken fibres whilst maintaining an evaluation of the various fields (stresses in particular).
In vitro degradation of porous PLLA/pearl powder composite scaffolds
2013
Abstract The in vitro degradation behavior of poly- l -lactide (PLLA), PLLA/aragonite pearl powder and PLLA/vaterite pearl powder scaffolds was investigated. The scaffolds were soaked in phosphate buffer solution (PBS) up to 200 days. Scanning electron microscopy (SEM), gel permeation chromatography (GPC), and differential scanning calorimetry (DSC) were used to observe any degradation of the scaffolds. Degradation behaviors such as changes in pH, porosity, bulk density, water absorption, weight loss and mechanical properties were discussed. The results show that a gradual increase of the pH in composite scaffolds can decrease the rate of hydrolysis of PLLA. PLLA/vaterite and PLLA/aragonite…
Acoustic methods for measuring the porosities of porous materials incorporating dead-end pores
2013
International audience; The acoustic properties of porous materials containing dead-end (DE) pores have been proposed by Dupont et al. [J. Appl. Phys. 110, 094903 (2011)]. In the theoretical description, two physical parameters were defined (the dead-end porosity and the average length of the dead-end pores). With the knowledge of the open porosity (measured with non-acoustic methods), and the measurement of kinematic porosity (also called the Biot porosity in this article), it is possible to deduce the dead-end porosity. Two acoustic methods for measuring the Biot porosity for a wide range of porosities are proposed. These methods are based on acoustic transmission and on the low and high …
Cariostatic effect of a light-cured, resin-reinforced glass-ionomer for bonding orthodontic brackets in vivo
1998
The aim of this study was to evaluate in vivo the cariostatic potential of the resin-reinforced glass-ionomer (Vitremer core build-up restorative; 3M Dental Product Division) when used as a bonding agent for orthodontic brackets. The mineral distribution and topography of the enamel surface adjacent to the bracket base was determined by quantitative microradiography (TMR) and confocal laser scanning microscopy (CLSM). The study was designed in split-mouth technique using 9 pairs of premolars to be extracted for orthodontic reasons. One tooth of each pair was bonded with the resin-reinforced glass-ionomer, and the control contralateral premolar with the non-fluoridated composite (Concise, 3M…
Minimal exposure time of different LED-curing devices
2007
Abstract Objectives The purpose of the study was to investigate the shortest possible exposure time of different LED-curing devices for five different resin composites in a clinically relevant in vitro-model, where a 7 mm distance from the light guide tip to the bottom side of the cavity was compiled. Methods Resin composite samples (Tetric EvoCeram A3, Filtek Supreme XT A3B, Premise A3, CeramX Mono M5, QuiXfil) were filled in three increments of 2 mm thickness each in stainless steel moulds (O = 5 mm, h = 6 mm, n = 9). The samples were incrementally exposed to different blue LED-curing devices (Bluephase, Bluephase C8, Bluephase 16i/Ivoclar Vivadent, L.E.Demetron II/sds Kerr, Elipar Free…
Rubidium dimers in paraffin-coated cells
2010
Measurements were made to determine the density of rubidium dimer vapor in paraffin-coated cells. The number density of dimers and atoms in similar paraffin-coated and uncoated cells was measured by optical spectroscopy. Due to the relatively low melting point of paraffin, a limited temperature range of 43-80 deg C was explored, with the lower end corresponding to a dimer density of less than 10^7 cm^(-3). With one-minute integration time, a sensitivity to dimer number density of better than 10^6 cm^(-3) was achieved. No significant difference in dimer density was observed between the cells.
Applications of Topological *-Algebras of Unbounded Operators
1998
In this paper we discuss some physical applications of topological *-algebras of unbounded operators. Our first example is a simple system of free bosons. Then we analyze different models which are related to this one. We also discuss the time evolution of two interacting models of matter and bosons. We show that for all these systems it is possible to build up a common framework where the thermodynamical limit of the algebraic dynamics can be conveniently studied and obtained.
A smart composite-piezoelectric one-dimensional finite element model for vibration damping analysis
2015
A one-dimensional finite element method for generally layered smart beams is presented in this paper. The model implements the first-order shear deformation beam theory and is based on the preliminary analytical condensation of the electric state to the mechanical state. This allows us to establish an effective mechanical beam kinematically equivalent to the original smart beam including the effects of electro-elastic couplings. The contributions of the external electric loads are included in both the equivalent stiffness properties and the equivalent mechanical boundary conditions. Hermite shape functions, which depend on parameters representative of the staking sequence through the equiv…
A topological model for Oersted-Amp�re's law
1973
A geometrical description of Oersted-Ampere's law ∮H ds=(4π/c)I can be given in terms of an appropriate topological manifold. More precisely: It will be shown that Oersted-Ampere's law can be related to the topological invariantH 1(S 1), i.e. de Rham's first cohomology group on the differentiable manifoldS 1={(x,y) ∈ ℝ2∶x 2+y 2}