Search results for "Pedestal"
showing 10 items of 10 documents
Numerical modelling for the diameter increase of silicon crystals grown with the pedestal method
2021
Abstract The pedestal method is one of crucible-free crystal growth methods, that has been less researched than the well-known floating zone (FZ) method. However, the pedestal method may be a cost-effective alternative to FZ, if large diameter feed rods are available. The investigated system contains two electromagnetic inductors: high-frequency inductor for pedestal top surface melting and middle-frequency inductor for pedestal side heating. The present work describes recent advances in numerical modelling of heat transfer and phase boundaries in axially symmetrical approximation, neglecting the melt flow. The shape of high-frequency inductor was optimized with the algorithm of gradient de…
Application of enthalpy model for floating zone silicon crystal growth
2017
Abstract A 2D simplified crystal growth model based on the enthalpy method and coupled with a low-frequency harmonic electromagnetic model is developed to simulate the silicon crystal growth near the external triple point (ETP) and crystal melting on the open melting front of a polycrystalline feed rod in FZ crystal growth systems. Simulations of the crystal growth near the ETP show significant influence of the inhomogeneities of the EM power distribution on the crystal growth rate for a 4 in floating zone (FZ) system. The generated growth rate fluctuations are shown to be larger in the system with higher crystal pull rate. Simulations of crystal melting on the open melting front of the pol…
El monumento a Cervantes en Valencia obra de Mariano Benlliure
2005
El Monumento a Cervantes erigido en Valencia tuvo su origen en la conmemoración del III Centenario de la publicación de El Quijote. La obra escultórica creada por Mariano Benlliure constituye un doble homenaje al genial escritor y al inmortal personaje, y una simbiosis formal de realismo e impresionismo. Al cumplirse el IV Centenario rememoramos aquel homenaje y sus vicisitudes y señalamos algunas de las diferentes representaciones escultóricas inspiradas en la figura del escritor y su obra en el transcurso de estos cien años. (A)
Laser Floating Zone Growth: Overview, Singular Materials, Broad Applications, and Future Perspectives
2021
This article belongs to the Special Issue Laser-Induced Crystallization.
Floating Zone Growth of Silicon
2015
Abstract The floating zone (FZ) technique changed from a crucible-free purification method into a growth technique mainly for high purity silicon crystals. The melt zone is inductively heated by the high frequency magnetic field of a sophisticated one-turn induction coil being the heart of the FZ growth. The needle-eye technique allows for crystals with large diameters beyond the capillary limitations of a cylindrical zone, but both electric breakthrough at the coil slit and bursting of the crystal by thermomechanical stress presently limit the diameter to 200 mm. A novel gFZ concept is depicted that works with granular silicon feedstock instead of expensive feed rods. The automation of the…
Overview of the JET results with the ITER-like wall
2013
Following the completion in May 2011 of the shutdown for the installation of the beryllium wall and the tungsten divertor, the first set of JET campaigns have addressed the investigation of the retention properties and the development of operational scenarios with the new plasma-facing materials. The large reduction in the carbon content (more than a factor ten) led to a much lower Zeff (1.2-1.4) during L- and H-mode plasmas, and radiation during the burn-through phase of the plasma initiation with the consequence that breakdown failures are almost absent. Gas balance experiments have shown that the fuel retention rate with the new wall is substantially reduced with respect to the C wall. T…
Simulated effects of W dust ablation and deposition on the pedestal edge in JET D and DT experiments
2022
Abstract A modelling analysis is performed on JET D and DT discharges, where W dust influx across the separatrix, in the pedestal edge region may affect L–H–L mode transition. The experimental basis of the proposed approach stems from the observation that transient impurity events (TIEs) are often associated with the presence of a shower of particles seen in the camera images and with strong optical emission. If the localised source of radiation is a number of heated or ablated large dust particles, then the questions addressed here are: how far will the ablated dust material penetrate and what effect will this have on the edge of the pedestal in relevant JET D and in a high fusion yield D–…
Erosion and screening of tungsten during inter/intra-ELM periods in the JET-ILW divertor
2020
Abstract Intra-ELM tungsten sources, which dominate the total W source, are quantified in the inner and outer divertor of JET-ILW. The amount of the sputtered W atoms for individual ELMs demonstrates a clear dependence on the ELM frequency. It decreases when the pedestal temperature is lower and, correspondingly, the ELM frequency is higher. Nevertheless, the entire gross erosion W source (the number of eroded W atoms per second due to ELMs) increases initially with ELM frequency and reaches its maximum at fELM ≈ 50–55 Hz followed by its reduction in the high frequency range. The in/out asymmetry of the intra-ELM W sources during ELMs is a critical issue and is investigated in this contribu…
Forward dihadron correlations in the Gaussian approximation of JIMWLK
2012
We compute forward dihadron azimuthal correlations in deuteron-gold collisions using a Gaussian approximation for the quadrupole operator. The double parton scattering contribution is found to be part of our dihadron calculation. We obtain a good description of the PHENIX data for the azimuthal-angle dependent away side peak and a relatively good estimate for the pedestal contribution.
Overview of the JET results in support to ITER
2017
The 2014–2016 JET results are reviewed in the light of their significance for optimising the ITER research plan for the active and non-active operation. More than 60 h of plasma operation with ITER first wall materials successfully took place since its installation in 2011. New multi-machine scaling of the type I-ELM divertor energy flux density to ITER is supported by first principle modelling. ITER relevant disruption experiments and first principle modelling are reported with a set of three disruption mitigation valves mimicking the ITER setup. Insights of the L–H power threshold in Deuterium and Hydrogen are given, stressing the importance of the magnetic configurations and the recent m…