Search results for "Porosimetry"
showing 10 items of 38 documents
The open metastable structure of a collapsible sand: fabric and bonding
2015
This paper deals with the compositional and textural characteristics determining open metastable structures in the pleistocenic sand outcropping in the Agrigento district (Sicily). The aim of the study was to individuate the bonding types occurring between grains that could generate matric suction phenomena. The composition and microfabric were characterised by means of granulometry, porosimetry, permeability, optical and ESEM-EDS microscopy, thermogravimetry and XR diffractometry, electric conductivity, and ionic chromatography. The data thus acquired show that the skeleton of the sand is constituted mostly by bioclasts and microfossils, calcite and quartz monocrystalline grains. Moreover,…
Characterization of the porous structure of Chilean volcanic soils by nitrogen adsorption and mercury porosimetry
2004
Pore volume, specific surface area (SSA), and total intragranular porosity (TIP) of Chilean soils derived from volcanic materials were studied. Soil samples involving the 0-15 and 15-30 cm depth of virgin and cultivated Collipulli (Ultisol) and Diguillin (Andisol) soils at two particle size fractions (<1 mm and <2 µm) were considered. From mercury porosimetry and N2 adsorption, mainly mesopores (pore diameter, dpore, about 10 nm) were determined for <1 mm Collipulli samples. Diguillin <1 mm soil shows macroporosity with dpore from 70 nm to 7000 nm. The clay fraction of Collipulli has macropores (dpore from 2000 nm to 40000 nm) and mesopores (dpore from 3 nm to 23 nm), while for Diguillin cl…
Experimental study of a naturally weathered stiff clay
2016
Studying the shear strength of a naturally weathered clay is important to understand rain-induced slope failures in weathered soils. However, experimental studies on naturally weathered soils are limited. The paper focuses on the laboratory experimental investigation carried out to analyse the shear strength of a naturally weathered stiff clay that can be found in unsaturated conditions in situ. This has an important practical relevance in the evaluation of the stability conditions of natural slopes at clay outcrops. Different experimental techniques of suction measurement were used to obtain the soil-water retention curve of the clay over a wide range of suctions. Scanning electronic micr…
Sol-gel derived anatase TiO2: morphology and photoactivity
1994
Abstract High-surface area TiO 2 (anatase) was prepared by the sol-gel method and characterized by various instrumental and analytical methods, including X-ray diffraction, thermogravimetric analysis, infrared spectroscopy, porosimetry, specific surface area measurements, scanning electron microscopy, and titration of surface hydroxyl groups. The specimen was tested for photodegradation of phenol and nitrophenols carried out in aqueous suspension at pH = 3; photoactivity was compared with that of commercially available anatase TiO 2 . Results are discussed in terms of porosity, surface area, and availability and population of surface OH groups, consequent upon the particular method used for…
Experimental assessment of the hydro-mechanical behaviour of a shale caprock during CO2 injection
2021
Abstract The presented experimental study focuses on the hydro-mechanical characterisation of a shale caprock (Opalinus Clay) in contact with carbon dioxide. The objective of this paper, consists in the evaluation of the material's sealing capacity in terms of entry-pressure, mechanical behaviour and sensitivity of the transport properties to chemo-mechanical effects induced by gaseous and liquid CO2 injection. Two types of Opalinus Clay core samples are tested; shaly and carbonate-rich. The sealing capacity has been evaluated on the shaly OPA according to the stepwise and the residual methods and compared to the results from mercury intrusion porosimetry. The obtained results and the diffe…
Investigation of characterizing methods for the microstructure of cement
2002
Volumetric, gravimetric, calorimetric, flow methods, mercury porosimetry and laser granulometry were used to investigate the surface structure and the sorption behavior of industrial cements and hydrated cement paste. The suitability of the measuring methods is assessed.
One dimensional consolidation of Opalinus Clay from shallow depth
2017
First experimental results on Opalinus Clay from shallow depth (< 30 m depth) are presented and compared to results on cores from Mont Terri Underground Rock Laboratory (~ 300 m depth). Samples were tested in one dimensional condition using an advanced experimental technique. The samples from the two sites show similar properties in terms of geotechnical characterization and one dimensional compressibility/swelling indexes, despite the different source depths.
Structural and surface characterization of the polycrystalline system CrxOy · TiO2 employed for photoreduction of dinitrogen and photodegradation of …
1992
The polycrystalline system CrxOy-TiO2, used as a catalyst for photoreactions, was studied by X-ray diffractometric method, visible-ultraviolet diffuse reflectance and infrared spectroscopic methods, surface area determination, and porosimetry to characterize its structural and surface features. Two series of catalysts were prepared by two different methods, namely by coprecipitation and by impregnation. The first series was tested as photocatalysts for the dinitrogen photoreduction in a gas-solid regime and for the phenol photodegradation in a liquid-solid regime. The results indicate that the interaction of chromium ions with OH groups modifies the surface properties of the supports and co…
One‐Pot Synthesis of a New High‐Aluminium‐Content Super‐Microporous Aluminosilicate
2006
A new super-microporous aluminosilicate having a high aluminium content (Si/Al ca. 1) has been prepared through a surfactant-assisted procedure with the use of a commercially available binary precursor (di-sec-butoxyaluminooxytriethoxysilane) as a single source of both Al and Si. The formation of super-micropores is a result of a significant network shrinkage associated with the thermal elimination of the surfactant. This solid has been studied by X-ray powder diffraction, electron microscopy, nuclear magnetic resonance spectroscopy and porosimetry. A preliminary analysis of the acidity and the catalytic activity of the super-microporous solid for the selective catalytic reduction of NOx is…
Liquid intrusion and alternative methods for the characterization of macroporous materials (IUPAC Technical Report)
2011
This document deals with the characterization of porous materials having pore widths in the macropore range of 50 nm to 500 μm. In recent years, the development of advanced adsorbents and catalysts (e.g., monoliths having hierarchical pore networks) has brought about a renewed interest in macropore structures. Mercury intrusion–extrusion porosimetry is a well-established method, which is at present the most widely used for determining the macropore size distribution. However, because of the reservations raised by the use of mercury, it is now evident that the principles involved in the application of mercury porosimetry require reappraisal and that alternative methods are worth being listed…