Search results for "RDW"
showing 10 items of 1401 documents
Performance evaluation of non volatile memories with a low cost and portable automatic test equipment
2017
This paper presents a versatile and portable test equipment, called portable ATE for research and development of non-volatile memories functionalities. The system is based on STM32-NUCLEO assembled with a custom designed daughter board, in order to host non-volatile memories test-chips, to manage the needed power supplies and generate suitable signals stimuli for correct operations. The system is controlled and programmed by a personal computer, via USB interface. In particular the system can perform: memory reading, writing and erasing, with settings flexibility on time and voltage levels; Electrical Stress Tests (Drain, Gate and Bulk Stress); Cycling Tests; debugging algorithms (erase or …
The positioning system of the ANTARES Neutrino Telescope
2012
The ANTARES neutrino telescope, located 40km off the coast of Toulon in the Mediterranean Sea at a mooring depth of about 2475m, consists of twelve detection lines equipped typically with 25 storeys. Every storey carries three optical modules that detect Cherenkov light induced by charged secondary particles (typically muons) coming from neutrino interactions. As these lines are flexible structures fixed to the sea bed and held taut by a buoy, sea currents cause the lines to move and the storeys to rotate. The knowledge of the position of the optical modules with a precision better than 10cm is essential for a good reconstruction of particle tracks. In this paper the ANTARES positioning sys…
New facets and an enhanced branch-and-cut for the min-max K -vehicles windy rural postman problem
2011
[EN] The min-max windy rural postman problem is a multiple vehicle version of the windy rural postman problem, WRPP, which consists of minimizing the length of the longest route to find a set of balanced routes for the vehicles. In a previous paper, an ILP formulation and a partial polyhedral study were presented, and a preliminary branch-and-cut algorithm that produced some promising computational results was implemented. In this article, we present further results for this problem. We describe several new facet-inducing inequalities obtained from the WRPP, as well as some inequalities that have to be satisfied by any optimal solution. We present an enhanced branch-and-cut algorithm that t…
Optimal Design of an X-Band, Fully-Coaxial, Easily-Tunable Broadband Power Equalizer for a Microwave Power Module
2020
A microwave power module (MPM), which is a hybrid combination of a solid-state power amplifier (SSPA) as a driver and a traveling-wave tube amplifier (TWT) as the final high power stage, is a high-power device largely used for radar applications. A gain equalizer is often required to flatten the TWT output power gain owing to its big gain fluctuations over the operating frequency range. In this paper, the design of an X-band, fully-coaxial, easily-tunable broadband power equalizer for an MPM is presented. The structure is composed of a coaxial waveguide as the main transmission line and a coaxial cavity loaded with absorbing material as a resonant unit. Sensitivity analyses of the attenuati…
Characteristic time scale of auroral electrojet data
1994
The structure function of the AE time series shows that the AE time series is self-affine such that the scaling exponent changes at the time scale of approximately 113 (±9) minutes. Autocorrelation function is shown to have scaling properties similar to those of the structure function. From this result it can be deduced that the time scale at which the scaling properties of the AE data change should equal the typical autocorrelation time of these data. We find the typical autocorrelation time of the AE data is 118 (±9) minutes. The characteristic time scale of the AE data appears as a spectral break in their power spectrum at a period of about twice the autocorrelation time.
Design of MOS Current Mode Logic Gates – Computing the Limits of Voltage Swing and Bias Current
2005
Minimizing a quality metric for an MCML gate, such as power-delay product or energy-delay product, requires solving a system of nonlinear equations subject to constraints on both bias current and voltage swing. In this paper, we will show that the limits of the swing and the bias current are affected by the constraints on maximum area and maximum delay. Moreover, methods for computing such limits are presented.
Minimum power-delay product design of MCML gates
2008
This paper describes a methodology for the minimization of the power-delay product of MCML gates. The method is based on the novel concept of crossing point capacitance. The methodology was been validated by designing several gates using in an IBM 130 nm CMOS process.
Understanding 802.11e contention-based prioritization mechanisms and their coexistence with legacy 802.11 stations
2005
The IEEE 802.11e task group has reached a stable consensus on two basic contention-based priority mechanisms to promote for standardization: usage of different arbitration interframe spaces and usage of different minimum/maximum contention windows. The goal of this article is to provide a thorough understanding of the principles behind their operation. To this purpose, rather than limit our investigation to high-level (e.g. throughput and delay) performance figures, we take a closer look at their detailed operation, also in terms of low-level performance metrics (e.g., the probability of accessing specific channel slots). Our investigation on one hand confirms that AIFS differentiation prov…
Modeling and 'smart' prototyping human-in-the-loop interactions for AmI environments
2021
[EN] Autonomous capabilities are required in AmI environments in order to adapt systems to new environmental conditions and situations. However, keeping the human in the loop and in control of such systems is still necessary because of the diversity of systems, domains, environments, context situations, and social and legal constraints, which makes full autonomy a utopia within the short or medium term. Human-system integration introduces an important number of challenges and problems that have to be solved. On the one hand, humans should interact with systems even in those situations where their attentional, cognitive, and physical resources are limited in order to perform the interaction.…
Towards a Secure DevOps Approach for Cyber-Physical Systems
2020
With the expansion of cyber-physical systems (CPSs) across critical and regulated industries, systems must be continuously updated to remain resilient. At the same time, they should be extremely secure and safe to operate and use. The DevOps approach caters to business demands of more speed and smartness in production, but it is extremely challenging to implement DevOps due to the complexity of critical CPSs and requirements from regulatory authorities. In this study, expert opinions from 33 European companies expose the gap in the current state of practice on DevOps-oriented continuous development and maintenance. The study contributes to research and practice by identifying a set of needs…