Search results for "RESISTANCE"

Performance evaluation and stability of silicide-based thermoelectric modules

2020

Abstract Long-term studies on thermoelectric generators based on N-type magnesium silicide (Mg2.01Si0.49Sn0.5Sb0.01) and P-type higher manganese silicide (Mn0.98Mo0.02Si1.73Ge0.02) materials are presented, in the operating temperature range of 200 °C–400 °C. Emphasis is put on the performance and reliability of the current collector configuration, especially on the hot side of the module, and on the thermomechanical stresses that are created during operation and lifetime testing as a result of large temperature gradients experienced across the thermoelectric legs. With silver (Ag) paste as contact material, the long term-stability of the uni-couples was carried out on non-metalized legs and…

Oxidation resistance of Ti 3 AlC 2 and Ti 3 Al 0.8 Sn 0.2 C 2 MAX phases: A comparison

2019

Ti3AlC2 and Ti3Al0.8Sn0.2C2 MAX phase powders are densified using Spark Plasma Sintering technique to obtain dense bulk materials. Oxidation tests are then performed over the temperature range 800-1000°C under synthetic air on the two different materials in order to compare their oxidation resistance. It is demonstrated that, in the case of the Ti3Al0.8Sn0.2C2 solid solution, the oxide layers consist in TiO2, Al2O3 and SnO2. The presence of Sn atoms in

Antiferromagnetic NiO thickness dependent sign of the spin Hall magnetoresistance in γ-Fe 2 O 3 /NiO/Pt epitaxial stacks

2019

We study the spin Hall magnetoresistance (SMR) in epitaxial γ–Fe2O3/NiO(001)/Pt stacks, as a function of temperature and thickness of the antiferromagnetic insulating NiO layer. Upon increasing the thickness of NiO from 0 nm to 10 nm, we detect a sign change of the SMR in the temperature range between 10 K and 280 K. This temperature dependence of the SMR in our stacks is different compared to that of previously studied yttrium iron garnet/NiO/Pt, as we do not find any peak or sign change as a function of temperature. We explain our data by a combination of spin current reflection from both the NiO/Pt and γ-Fe2O3/NiO interfaces and the thickness-dependent exchange coupling mode between the …

High-Performance Flexible Magnetic Tunnel Junctions for Smart Miniaturized Instruments

2018

Multi-pulse characterization of trapping/detrapping mechanisms in AlGaN/GaN high electromobility transistors

2019

GaN high-electro mobility transistors (HEMTs) are among the most promising candidates for use in high-power, high-frequency, and high-temperature electronics owing to their high electrical breakdown threshold and their high saturation electron velocity. The applications of these AlGaN/GaN HEMTs in power converters are limited by the surface trapping effects of drain-current collapse. Charge-trapping mechanisms affect the dynamic performance of all GaN HEMTs used in power switching applications. This study analyzes the dynamic resistance of GaN HEMTs and finds that the effects of dynamic resistance can be suppressed by controlling switching conditions and on-off cycles.

Electrical Modeling of Monolithically Integrated GMR Based Current Sensors

2018

We report on the electrical compact model, using Verilog-A, of a monolithically integrated giant magnetoresistance (GMR) based electrical current sensors. For this purpose, a specifically designed ASIC (AMS $0.35\mu \mathrm{m}$ technology) has been considered, onto which such sensors have been patterned and fabricated, following a two-steps procedure. This work is focused on the DC regime model extraction, giving evidences of its good performance and stating the bases for subsequent model improvements.

Ab initio modelling of the Y, O, and Ti solute interaction in fcc-Fe matrix

2018

Abstract Strengthening of the ODS steels by Y2O3 precipitates permits to increase their operation temperature and radiation resistance, which is important in construction materials for future fusion and advanced fission reactors. Both size and spatial distribution of oxide particles significantly affect mechanical properties and radiation resistance of ODS steels. Addition of the Ti species (present also as a natural impurity atoms in iron lattice) in the particles of Y2O3 powder before their mechanical alloying leads to the formation of YTiO3, Y2TiO5, and Y2Ti2O7 nanoparticles in ODS steels. Modelling of these nanoparticle formation needs detailed knowledge of the energetic interactions be…

Radiation resistance of nanolayered silicon nitride capacitors

2020

Abstract Single-layered and multi-layered 20–60 nm thick silicon nitride (Si3N4) dielectric nanofilms were fabricated using a low-pressure chemical vapour deposition (LPCVD) method. The X-ray photoelectron spectroscopy (XPS) confirmed less oxygen content in the multi-layered nanofilms. The capacitors with Si3N4 multilayer demonstrated a tendency to a higher breakdown voltage compared to the capacitors with Si3N4 single layer. Si3N4 nanofilms and capacitors with Si3N4 dielectric were exposed to 1 kGy dose of gamma photons. Fourier transform infrared (FTIR) spectroscopy analysis showed that no modifications of the chemical bonds of Si3N4 were present after irradiation. Also, gamma irradiation…

Microfabricated high temperature sensing platform dedicated to scanning thermal microscopy (SThM)

2018

Abstract The monitoring of heat flux is becoming more and more critical for many materials and structures approaching nanometric dimensions. Scanning Thermal Microscopy (SThM) is one of the tools available for thermal measurement at the nanoscale and requires calibration. Here we report on a micro-hotplate device made of a platinum heater suspended on thin silicon nitride (SiN) membranes integrating specific features for SThM calibration. These heated reference samples can include a localized resistive temperature sensors (RTD) or standalone platinum membranes (typically 10 × 10 μm2) on which the temperature can be measured precisely. This functional area is dedicated to (1) estimate the th…

Improving the high temperature oxidation resistance of Ti-β21S by mechanical surface treatment

2020

The improvement of the high temperature oxidation resistance of titanium alloys is currently a technological challenge. Mechanical surface treatments as shot-peening (SP) have shown their ability to improve the behaviour of pure zirconium and titanium. However, shot-peening treatments can induce a significant surface contamination. Laser shock peening (LSP) appears as a good alternative. Here, we have investigated the effect of SP and LSP treatments on the HT oxidation behavior of Ti-β21S. Samples treated by these methods have been compared to untreated ones for long exposures (3000 h) at 700 °C in dry air. The samples placed in a furnace at 700 °C were periodically extracted to be weighed.…