Search results for "Roboti"
showing 10 items of 687 documents
Intentional weld defect process: From manufacturing by robotic welding machine to inspection using TFM phased array
2019
Specimens with intentionally embedded weld defects or flaws can be employed for training, development and research into procedures for mechanical property evaluation and structural integrity assessment. It is critical that the artificial defects are a realistic representation of the flaws produced by welding. Cylindrical holes, which are usually machined after welding, are not realistic enough for our purposes as it is known that they are easier to detect than the naturally occurring imperfections and cracks. Furthermore, it is usually impractical to machine a defect in a location similar to where the real weld defects are found. For example, electro-discharge machining can prod…
In-process calibration of a non-destructive testing system used for in-process inspection of multi-pass welding
2020
Abstract In multi-pass welding, there is increasing motivation to move towards in-process defect detection to enable real-time repair; thus avoiding deposition of more layers over a defective weld pass. All defect detection techniques require a consistent and repeatable approach to calibration to ensure that measured defect sizing is accurate. Conventional approaches to calibration employ fixed test blocks with known defect sizes, however, this methodology can lead to incorrect sizing when considering complex geometries, materials with challenging microstructure, and the significant thermal gradients present in materials during the inter-pass inspection period. To circumvent these challenge…
Dynamical behaviour of pneumatic artificial muscles
2014
The mechanical response of pneumatic artificial muscles is analyzed in transient and periodic conditions, assuming the inextensibility of the sheathing fibres and considering the influence of the texture geometry, of the dissipation due to the mutual sliding between the braids and of the stress field inside the bladder thickness, where the constituent elastomer is regarded as a two-parameter Mooney–Rivlin material. The polytropic exponent of the thermodynamic air evolution inside the muscle during the charging and discharging phases may be properly chosen depending on the working frequency. The muscle end shape is taken into account profiling the meridian section by a simple m-degree parabo…
Switchable surface structured hydrogel coatings
2017
Switchable surface structures based on hydrogels are an emerging field in material science, microfluidics, soft robotics and anti-fouling. Here, we describe a novel method that uses a photo-cross-linkable terpolymer to create a hydrogel coating with a switchable surface structure. The terpolymer is based on poly(N-isopropylacrylamide) (PNIPAm) and it is shown that simple coating technologies like slit die coating can be used under ambient conditions. It is also shown that the swelling ratio of the coating is controlled by the energy dose of ultraviolet (UV) light. Simple and complex surface structures were created using respectively single or multiple UV illumination steps through masks and…
Wavelength-Gated Adaptation of Hydrogel Properties via Photo-Dynamic Multivalency in Associative Star Polymers.
2020
Abstract Responsive materials, such as switchable hydrogels, have been largely engineered for maximum changes between two states. In contrast, adaptive systems target distinct functional plateaus between these maxima. Here, we demonstrate how the photostationary state (PSS) of an E/Z‐arylazopyrazole photoswitch can be tuned by the incident wavelength across a wide color spectrum, and how this behavior can be exploited to engineer the photo‐dynamic mechanical properties of hydrogels based on multivalent photoswitchable interactions. We show that these hydrogels adapt to the wavelength‐dependent PSS and the number of arylazopyrazole units by programmable relationships. Hence, our material des…
A theoretical approach to pneumatic muscle mechanics
2013
The mechanical response of pneumatic artificial muscles is analyzed assuming the inextensibility of the sheathing braids and taking into account the stress field inside the rubber bladder, which is regarded as a Mooney-Rivlin hyperelastic material. The end effects are simulated by heuristically profiling the meridian section. After estimating the constitutive parameters by traction tests on rubber specimens, the theoretical results are compared with experiments and a satisfactory accordance may be detected.
A homography formulation to the 3pt plus a common direction relative pose problem
2014
International audience; In this paper we present an alternative formulation for the minimal solution to the 3pt plus a common direction relative pose prob-lem. Instead of the commonly used epipolar constraint we use the homog-raphy constraint to derive a novel formulation for the 3pt problem. This formulation allows the computation of the normal vector of the plane defined by the three input points without any additional computation in addition to the standard motion parameters of the camera. We show the working of the method on synthetic and real data sets and compare it to the standard 3pt method and the 5pt method for relative pose estima-tion. In addition we analyze the degenerate condi…
Robotic path planning for non-destructive testing – A custom MATLAB toolbox approach
2016
AbstractThe requirement to increase inspection speeds for non-destructive testing (NDT) of composite aerospace parts is common to many manufacturers. The prevalence of complex curved surfaces in the industry provides motivation for the use of 6 axis robots in these inspections. The purpose of this paper is to present work undertaken for the development of a KUKA robot manipulator based automated NDT system. A new software solution is presented that enables flexible trajectory planning to be accomplished for the inspection of complex curved surfaces often encountered in engineering production. The techniques and issues associated with conventional manual inspection techniques and automated s…
A cooperative mobile robot and manipulator system (Co-MRMS) for transport and lay-up of fibre plies in modern composite material manufacture
2021
AbstractComposite materials are widely used in industry due to their light weight and specific performance. Currently, composite manufacturing mainly relies on manual labour and individual skills, especially in transport and lay-up processes, which are time consuming and prone to errors. As part of a preliminary investigation into the feasibility of deploying autonomous robotics for composite manufacturing, this paper presents a case study that investigates a cooperative mobile robot and manipulator system (Co-MRMS) for material transport and composite lay-up, which mainly comprises a mobile robot, a fixed-base manipulator and a machine vision sub-system. In the proposed system, marker-base…
Comprehensive simulation of cooperative robotic system for advanced composite manufacturing : a case study
2021
Composite materials are widely used because of their light weight and high strength properties. They are typically made up of multi-directional layers of high strength fibres, connected by a resin. The manufacturing of composite parts is complex, time-consuming and prone to errors. This work investigates the use of robotics in the field of composite material manufacturing, which has not been well investigated to date (particularly in simulation). Effective autonomous material transportation, accurate localization and limited material deformation during robotic grasping are required for optimum placement and lay-up. In this paper, a simulation of a proposed cooperative robotic system, which …