Search results for "STAI"
showing 10 items of 5922 documents
Experimental analysis of materials in proton exchange membrane electrolysis cells
2019
Abstract An accelerated supply and demand of energy has resulted in an increased need for efficient energy storage options, where storing energy in hydrogen gas emerges as one of the most attractive. In this study, a singular proton exchange membrane (PEM) electrolysis cell was designed using adequately low-cost materials, and tested using polarisation curves, cyclic voltammetry and AC impedance. A comparative study of various micro porous layer (MPL) materials was performed in an effort to find suitable options which are able to steadily operate under anodic conditions. The best performance was achieved using carbon cloth, however this material was unstable. Untreated porous titanium and n…
Effect of coatings on long term behaviour of a commercial stainless steel for solid oxide electrolyser cell interconnect application in H2 /H2O atmos…
2014
Abstract K41X (AISI 441) stainless steel evidenced a high electrical conductivity after 3000 h ageing in H 2 /H 2 O side when used as interconnect for solid oxide electrolyser cells (SOEC) working at 800 °C. Perovskite (La 1 − x Sr x MnO 3 − δ ) and spinel (Co 3 O 4 ) oxides coatings were applied on the surface of the ferritic steel for ageing at 800 °C for 3000 h. Both coatings improved the behaviour of the steel and give interesting opportunities to use the K41X steel as interconnect for hydrogen production via high temperature steam electrolysis. Co 3 O 4 reduced into Co leading to a very good Area Specific Resistance (ASR) parameter, 0.038 Ω cm 2 . Despite a good ASR (0.06 Ω cm 2 ), La …
Dual atmosphere study of the K41X stainless steel for interconnect application in high temperature water vapour electrolysis
2015
Abstract High temperature water vapour electrolysis (HTE) is one of the most efficient technologies for mass hydrogen production. A major technical difficulty related to high temperature water vapour electrolysis is the development of interconnects working efficiently for a long period. Working temperature of 800 °C enables the use of metallic materials as interconnects. High temperature corrosion behaviour and electrical conductivity of a commercial stainless steel, K41X (AISI 441), were tested in HTE dual atmosphere (95%O 2 -5%H 2 0/10%H 2 -90%H 2 O) at 800 °C. The alloy exhibits a very good oxidation resistance compared to single atmosphere tests. However, a supplied electrical current s…
Design of a LLC Resonant Converter for Powering a PEM Electrolyzer
2021
International audience; This paper proposes the design of a LLC resonant converter to supply a proton exchange membrane (PEM) electrolyzer. The PEM requires a low voltage with high current, a reduced output voltage ripple, and an overdamped dynamic behavior of the converter to avoid voltage overshoots. The designed converter allows satisfying the design constraints, minimizing switching and reverse recovery losses; the efficiency is influenced mainly by the output rectifier's conduction losses.
Reaction Condition Screening by Using Electrochemical Microreactor: Application to Anodic Phenol-arene C,C Cross-Coupling Reaction in High Acceptor N…
2013
The anodic phenol-arene C,C cross-coupling reaction was achieved in inexpensive and sustainable media such as methanol, acetic acid, and formic acid by using an electrochemical microreactor which can provide a better performance to screen reaction conditions than in standard beaker-type electrolysis cells. Especially, formic acid as a reaction medium showed good performance. The total amount of cross-coupling product and homo-coupling products as a by-product was clearly increased as the solvent acceptor number increased. To control the selective oxidation of phenol, addition of methanol was effective.
Electrolyses model development for metal/electrolyte interface: Testing with microrespiration sensors
2011
Abstract Initial process of electrolysis is investigated using platinum and tungsten wires as hydrogen electrodes and inductive kickback voltage peak based power unit. Microelectrodes are used to determine concentrations of dissolved hydrogen and pH close to wire electrodes. It is observed that concentration of dissolved hydrogen increases faster on tungsten electrode as on platinum. Authors explain this fact with differences of hydrogen evolution reaction on both materials – inductive kickback voltage peak power unit is supplying very short voltage pulses with limited energy what is enough only for hydrogen adsorption on platinum electrode, but is sufficient for full hydrogen evolution rea…
Influence of combined electromagnetic fields on the heat/mass transfer in the Bridgman process
2002
The influence of combined magnetic fields (travelling and rotating) on the characteristics of heat/mass transfer with an aim to obtain the needed profile of the interface is considered, that is a necessary condition, which insures the homogeneity of single crystal content. The crystallization process of a cylindrical sample is considered. It was presumed that the sample moves with a permanent velocity towards the cold part of the heater and a partial-linear temperature distribution characteristic to the Bridgman method was set in along the heater's length. Permanent temperature values were set in on the top and bottom edges of the calculation mesh. It has been shown that combinations of dif…
Transmission electron microscopy in molecular structural biology: A historical survey.
2015
In this personal, historic account of macromolecular transmission electron microscopy (TEM), published data from the 1940s through to recent times is surveyed, within the context of the remarkable progress that has been achieved during this time period. The evolution of present day molecular structural biology is described in relation to the associated biological disciplines. The contribution of numerous electron microscope pioneers to the development of the subject is discussed. The principal techniques for TEM specimen preparation, thin sectioning, metal shadowing, negative staining and plunge-freezing (vitrification) of thin aqueous samples are described, with a selection of published im…
Simultaneous determination of carrier lifetime and electron density-of-states in P3HT:PCBM organic solar cells under illumination by impedance spectr…
2010
We report new insights into recombination kinetics in poly(3-hexylthiophene):methanofullerene (P3HT:PCBM) bulk heterojunction (BHJ) solar cells, based on simultaneous determination of the density of states (DOS), internal recombination resistance, and carrier lifetime, at different steady states, by impedance spectroscopy. A set of measurements at open circuit under illumination was performed aiming to better understand the limitations to the photovoltage, which in this class of solar cells remains far below the theoretical limit which is the difference between the LUMO level of PCBM and the HOMO of P3HT (∼1.1 eV). Recombination kinetics follows a bimolecular law, being the recombination ti…
Study of the annealing conditions and photoelectrochemical characterization of a new iron oxide bi-layered nanostructure for water splitting
2016
Iron oxide nanostructures have emerged as promising materials for being used as photocatalysts for hydrogen production due to their advantageous properties. However, their low carrier mobility and short hole diffusion length limit their efficiency in water splitting. To overcome these drawbacks, in the present study, we synthetized a new hematite (alpha-Fe2O3) bi-layered nanostructure consisting of a top nanosphere layer and a nanotubular underneath one by electrochemical anodization. Annealing parameters such as temperature, heating rate and atmosphere were studied in detail in order to determine the optimum annealing conditions for the synthetized nanostructure. The obtained new bi-layere…