Search results for "STING"

Prediction of Ductile Fractures in Metal-Forming Processes: an Approach Based on the Damage Mechanics

1994

The Authors propose a new approach for the prediction of ductile fractures in bulk metal forming processes: the approach is based on a numerical analysis able to take into account damage occurrence and evolution in constitutive equations. The model supplies the distribution of the void volume fraction in the workpiece during the deformation path: consequently, the comparison to a critical value, determined by means of a simple tension test, allows to predict the growth of defects. The proposed approach has been applied to the drawing process: the numerical results have been compared with a set of experimental tests showing a good predictive capability of the model.

Mechanical behaviour of natural cow leather in tension

2009

We study experimentally the microstructure and mechanical behavior of natural cow leather. Tensile tests are performed using leather strips to observe their deformation, creep and failure. It is found that the microstructure of cow leather is a layered, complicated network of fibers of different sizes from a few to a few hundreds of nanometers in diameter. They show nonlinear stress-strain relations and viscoelastic behavior. The effect of humidity is also examined. A simple theoretical model of a multilayered beam is proposed to describe the most basic behavior in tension.

Effect of water contamination on the shear bond strength of five orthodontic adhesives

2010

Objectives: To evaluate the shear bond strength and site of failure of brackets bonded to dry and wet enamel. Study design: 50 teeth were divided into ten groups of 5 teeth each (10 surfaces). In half the groups enamel was kept dry before bonding, and in the other half distilled water was applied to wet the surface after etching. The following groups were established: 1)Acid/Transbond-XT (dry/wet) XT; 2) Transbond Plus Self Etching Primer (TSEP)/Transbond-XT paste (dry/wet); 3) Concise (dry), Transbond MIP/Concise (wet), 4) FujiOrtho-LC (dry/ wet); 5) SmartBond (dry/wet). Brackets were bonded to both buccal and lingual surfaces. Specimens were stored in distilled water (24 hours at 37ºC) an…

The Use of Atomic Force Microscopy in Determining the Stiffness and Adhesion Force of Human Dentin After Exposure to Bleaching Agents

2009

Introduction: Oxidant bleaching agents may induce several alterations on mineralized teeth tissues. Our aim is to study,at the ultrastructurallevel,mechanicalmodifications induced on dentin after exposure to different bleaching agents.Methods: Nanoindentation performed with atomic force microscopy was used to measure changes in dentin stiffness as well as the adhesion force between the tip and the tissue both in intertubular and peritubulardentin.Foreachspecimen,dentinlocalization, and bleaching agent, 100 independent nanoindentations were performed. Carbamide peroxide (30%) and hydrogenperoxide(35%) wereusedasbleaching agents. Results: A significant reduction of both stiffness and adhesion…

Casein phosphopeptide-amorphous calcium phosphate effects on brackets shear bond strength and enamel damage

2017

Background The aim of study was to evaluate the application of casein phosphopeptide-amorphous calcium phosphate (CPP-ACP) and fluoride regarding their effect on the shear bond strength (SBS), bond failure pattern of brackets using the adhesive remnant index (ARI) and assessing the quality of enamel surface using the enamel damage index (EDI). Material and methods Sixty extracted premolar teeth were randomly divided into four groups regarding pretreatment application of CPP-ACP and fluoride. Brackets were bonded using the conventional method. Specimens were thermocycled for 1000 cycles and were subsequently tested for the SBS in a universal testing machine. After debonding, the teeth were e…

Spray-Drying, Solvent-Casting and Freeze-Drying Techniques: a Comparative Study on their Suitability for the Enhancement of Drug Dissolution Rates.

2019

Purpose Solid dispersions (SDs) represent the most common formulation technique used to increase the dissolution rate of a drug. In this work, the three most common methods used to prepare SDs, namely spray-drying, solvent-casting and freezedrying, have been compared in order to investigate their effect on increasing drug dissolution rate. Methods Three formulation strategies were used to prepare a polymer mixture of polyvinyl-alcohol (PVA) and maltodextrin (MDX) as SDs loaded with the following three model drugs, all of which possess a poor solubility: Olanzapine, Dexamethasone, and Triamcinolone acetonide. The SDs obtained were analysed and compared in terms of drug particle size, drug-lo…

Effect of temperature on the orthodontic clinical applications of NiTi closed-coil springs

2013

NiTi spring coils were used to obtain large deformation under a constant force. The device consists on a NiTi coil spring, superelastic at body temperature, in order to have a stress plateau during the austenitic retransformation during the unloading. The temperature variations induced changes in the spring force. Objectives: The aim of this study is to investigate the effect of the temperature variations in the spring forces and corrosion behaviour simulating the ingestion hot/cold drinks and food. Study D esign: The springs were subjected to a tensile force using universal testing machine MTS-Adamel (100 N load cell). All tests were performed in artificial saliva maintained at different t…

Fatigue strength of a single lap joint SPR-bonded

2011

In the last years, hybrid joints, meaning with this the joints which consist in combining a traditional mechanical joint to a layer of adhesive, are gradually attracting the attention of various sectors of the construction of vehicles and transportation industries, for their better performance compared to just mechanical joints (self-piercing riveting SPR, riveting, and so on) or just to bonded joints. The paper investigates the fatigue behavior of a single lap joint self-piercing riveted (SPR) and bonded throughout fatigue tests. The considered geometric configuration allowed the use of two rivets placed longitudinally; an epoxy resin was used as adhesive. In the first part of the work sta…

Role of Intrinsic Dipoles in the Evaporation‐Driven Assembly of Perovskite Nanocubes into Energy‐Harvesting Composites

2020

Eddy-Current Imaging with Nitrogen-Vacancy Centers in Diamond

2018

We demonstrate microwave-free eddy-current imaging using nitrogen-vacancy centers in diamond. By detecting the eddy-current induced magnetic field of conductive samples, we can distinguish between different materials and shapes and identify structural defects. Our technique allows for the discrimination of different materials according to their conductivity. The sensitivity of the measurements is calculated as 8$\times 10 ^{5}$\,S/m\,$\sqrt[]{\textrm{Hz}}$ at 3.5\,MHz, for a cylindrical sample with radius $r_0$\,=\,1\,mm and height $h$\,=\,0.1\,mm (volume $\sim$\,0.3\,mm$^3$), at a distance of 0.5\,mm. In comparison with existing technologies, the diamond-based device exhibits a superior ba…