Search results for "Softwood"
showing 10 items of 29 documents
Automatic measurement of wood fiber orientation and knot detection using an optical system based on heating conduction.
2015
In this paper, a new approach to computing the deviation of wood grain is proposed. To do this, the thermal conduction properties of timber are used (higher conduction in the fiber direction). Exciting the surface of the wood with a laser and capturing the thermal conduction using a thermal camera, an ellipse can be observed. Using a method similar to the tracheid effect, it is possible to extract information from this ellipse, such as the slope of grain and the presence of knots. With this method it is therefore possible to extend the mechanical model (assessing the mechanical properties of timber) to take certain singularities into account. Using this approach, the slope of grain can be e…
Utilization of lignin powder for manufacturing self-binding HDF
2017
Abstract The preparation of self-binding lignocellulosic fibreboards has been investigated. Different high-density fibreboards (HDF) were hot-pressed based on a mixture of grey alder (Alnus incana L. Moench) wood chips processed by steam explosion auto-hydrolysis (SE) and 15% or 25% lignin content from three different industrial sources: softwood kraft lignin (SWKL), soda wheat straw lignin (SoWhStL) and hydrolysis wheat straw lignin (HWhStL). Density, thickness swelling (TS) after immersion in water for 24 h, modulus of rupture (MOR), modulus of elasticity (MOE) and strength of internal bond (IB) of the board samples were determined. The amount (15% or 25%) and moisture content (MC) (18±1%…
Spectroscopic analysis of hot-water- and dilute-acid-extracted hardwood and softwood chips
2017
Hot-water and dilute sulfuric acid pretreatments were performed prior to chemical pulping for silver/white birch (Betula pendula/B. pubescens) and Scots pine (Pinus sylvestris) chips to determine if varying pretreatment conditions on the original wood material were detectable via attenuated total reflectance (ATR) infrared spectroscopy. Pretreatment conditions varied with respect to temperature (130 °C and 150 °C) and treatment time (from 30 min to 120 min). The effects of the pretreatments on the composition of wood chips were determined by ATR infrared spectroscopy. The spectral data were compared to those determined by common wood chemistry analyses to evaluate the suitability of ATR spe…
Evaluation of Ligno Boost™ softwood kraft lignin epoxidation as an approach for its application in cured epoxy resins
2018
Abstract In this study, modification of LignoBoost™ softwood kraft lignin with epichlorhydrin in water-organic solvents media was realized. Lignin-based epoxy resins were obtained by two ways: acetone extraction of glycidylated lignin or glycidylation of the acetone soluble lignin fraction. The effect of glycidylation regimes on the yields of acetone soluble fractions, their functional composition and physical-chemical characteristics was investigated using wet chemistry methods, FTIR spectroscopy, size exclusion chromatography (SEC) and differential scanning calorimetry (DSC). The positive effect of the biphasic phase transfer catalytic system – KOH/quaternary ammonium salt – on glycidylat…
Alkali consumption of aliphatic carboxylic acids during alkaline pulping of wood and nonwood feedstocks
2013
Abstract The carbohydrate degradation products have been examined, which are formed during the conventional kraft pulping of a softwood, hardwoods, bamboo, and wheat straw as well as soda and soda-anthraquinone pulping of wheat straw. The focus was on “volatile” acids such as formic and acetic acids and “nonvolatile” hydroxy monocarboxylic and dicarboxylic acids. The different consumption profiles were obtained for the charged alkali required for the neutralization of these aliphatic acids depending on the feedstock and the cooking method. The relative composition of the acid fraction in the black liquors of softwood and hardwood and nonwood feedstocks showed characteristic variations. Howe…
Chlorophenanthrenes, alkylchlorophenanthrenes and alkylchloronaphthalenes in kraft pulp mill products and discharges
1994
Abstract Chlorinated phenanthrenes (PCPHs; P=1–5), alkylphenanthrenes (C4-PCPHs; P=1–3), dimethylnaphthalenes (C2-PCNs; P=1–4) and trimethylnaphthalenes (C3-PCNs; P=1–2) were analyzed by high resolution gas chromatography/high resolution mass spectrometry (HRGC/HRMS) in pulp, effluent and biosludge of two kraft pulp mills (mills 1 and 2). These compounds were indicated to be formed in the manufacture of both bleached hardwood and softwood kraft pulp. Different compound groups dominated in mill 1 samples compared to mill 2 samples. Differences between birch and pine pulp from mill 1 were observed for all substance groups but in mill 2 pulp only for PCPHs. The highest concentrations of PCPHs …
Free and bound chlorophenols in kraft pulp bleaching effluents
1992
Abstract Free (F; hexane extractable) and chemically bound (B; alkali extractable) chlorophenols, catechols and guaiacols were measured from effluents of the C and E stages of chlorobleaching of kraft softwood pulp. Ratio B/F was in moste cases nearly one, but for tetrachloroguaiacol B/F was 20 in C and 2.70 in E stage. Organically bound chlorine (OCl) in chlorophenols was less than one percent of the total AOX (Adsorbable Organic Halogen) emitted.
Multivariate Correlation between Analytical Data for Various Organics Dissolved during Autohydrolysis of Silver Birch (Betula pendula) Chips and Trea…
2014
Autohydrolysis pre-treatments were performed for the production of hemicellulose-rich autohydrolysates from silver birch (Betula pendula) chips prior to chemical pulping. Pre-treatment conditions were varied with respect to time (from 30 to 120 min) and temperature (130 and 150 °C), covering a P-factor range from 10 to 238. Hydrolysates were analyzed in terms of carbohydrates, lignin, volatile organic acids, and furanoic compounds. The analytical data were subjected to various chemometric techniques to establish the relationships between dissolved organic components, hardwood and softwood used in the experiments, and applied pre-treatment conditions. Using this method, differences between t…
Electric Field Effect on the Thermal Decomposition and Co-combustion of Straw with Solid Fuel Pellets
2019
The aim of this study was to provide more effective use of straw for energy production by co-firing wheat straw pellets with solid fuels (wood, peat pellets) under additional electric control of the combustion characteristics at thermo-chemical conversion of fuel mixtures. Effects of the DC electric field on the main combustion characteristics were studied experimentally using a fixed-bed experimental setup with a heat output up to 4 kW. An axisymmetric electric field was applied to the flame base between the positively charged electrode and the grounded wall of the combustion chamber. The experimental study includes local measurements of the composition of the gasification gas, flame tempe…
Solid-liquid nuclear magnetic resonance relaxation and signal amplitude relationships with ranking of seasoned softwoods and hardwoods
2006
In 1H NMR (Nuclear Magnetic Resonance) relaxation measurements for a set of eight hardwood and softwood samples, each Free Induction Decay (FID) is fit by the sum of a “Solid” signal of the form A exp[−c(t/Ts)2] [1−g(t/Ts)2+h(t/Ts)4] plus a “Liquid” signal B exp(−t/T2 FID). Distributions of longitudinal (T1) relaxation times were computed separately for the Solid and Liquid components, giving also the Solid/Liquid 1H ratio α. From measurements on the samples dried, seasoned, and hydrated, the moisture content, (Liquid/Solid weight ratio) was found to be approximately 0.50/α. For each of the “Seasoned” samples (10-13% moisture content) a single T1 peak was found for the Solid and two for the…