Search results for "Stress-strain"
showing 10 items of 13 documents
Experimental results of RC columns strengthnened with Fiber Reinforced Cementitious Mortars
2012
The structural behaviour of reinforced concrete columns strengthened with a system made up of fibre nets embedded in an inorganic stabilized cementitious matrix was investigated. Specimens with circular and square cross-section were cast and subjected to monotonic uniaxial compression to investigate the efficiency of a Polypara-phenylene-benzo-bisthiazole (PBO) Fibre Reinforced Cementitious Mortars (FRCM) system in increasing both carrying capacity and ductility. The experimental results show that confinement with PBO fibre produced a noticeable increment in strength and ductility, though the low mechanical ratios of fibre considered were not always able to ensure hardening behaviour up to …
Stress-Strain Law for Confined Concrete with Hardening or Softening Behavior
2013
This paper provides a new general stress-strain law for concrete confined by steel, fiber reinforced polymer (FRP), or fiber reinforced cementitious matrix (FRCM), obtained by a suitable modification of the well-known Sargin’s curve for steel confined concrete. The proposed law is able to reproduce stress-strain curve of any shape, having both hardening or softening behavior, by using a single closed-form simple algebraic expression with constant coefficients. The coefficients are defined on the basis of the stress and the tangent modulus of the confined concrete in three characteristic points of the curve, thus being related to physical meaningful parameters. It will be shown that if the v…
Local Buckling of reinforcing steel bars in RC members under compression forces
2018
Buckling of longitudinal bars is a brittle failure mechanism, often recorded in reinforced concrete (RC) structures after an earthquake. Studies in the literature highlights that it often occurs when steel is in the post elastic range, by inducing a modification of the engineered stress-strain law of steel in compression. A proper evaluation of this effect is of fundamental importance for correctly evaluating capacity and ductility of structures. Significant errors can be obtained in terms of ultimate bending moment and curvature ductility of an RC section if these effects are not accounted, as well as incorrect evaluations are achieved by non-linear static analyses. This paper presents a n…
Compressive behavior of short high-strength concrete columns
2010
Abstract The focus of the present paper is the compressive response of short high strength reinforced concrete members. Members have square transverse cross-sections and they are reinforced with longitudinal steel bars and transverse stirrups. A preliminary analysis to check the stability condition of longitudinal bars was made to verify that buckling occurs after yielding in compression. Prescriptions on required diameter and spacing of stirrups are given. In the following, a model is presented which allows us to evaluate the confinement pressures exercised by transverse steel and by longitudinal bars during the loading process taking into account the interaction of the stirrups with the i…
Influence of steel reinforcements on the behavior of compressed high strength R.C. circular columns
2012
Abstract In the present paper the focus is on the compressive response of short high strength reinforced concrete members having circular transverse cross-sections and reinforced with longitudinal steel bars and transverse spirals or hoops. An analytical model is proposed which allows one to estimate the confinement pressures exerted by transverse steel and by longitudinal bars during the loading process, taking into account the interaction of the hoops or spirals with the inner core both in the plane of the transverse steel and in the space between two successive hoops. Yielding of steel spirals or hoops and longitudinal bars including buckling phenomena and damage to the concrete core are…
Definition of a fiber macro-model for nonlinear analysis of infilled frames
2017
A common way to model infill-frame interaction is the use equivalent strut macromodels. In most cases these are compression only resistant truss elements defined with a multi-linear axial-force / axial-displacement law. The main difficulty in using this approach is to correctly calibrate such a force-displacement curve (slope of ascending and post-peak branches, critical yielding, peak and residual forces) because of the large number of variables (mechanical and elastic properties of materials) and the different possible damage mechanisms activated for the frame-infill system. Another possible way is using fiber-section elements as diagonal struts. In this case the force-displacement law is…
Apparent interfacial shear strength of short-flax-fiber/starch acetate composites
2016
Abstract The paper deals with an indirect industry-friendly method for identification of the interfacial shear strength (IFSS) in a fully bio-based composite. The IFSS of flax fiber/starch acetate is evaluated by a modified Bowyer and Bader method based on an analysis of the stress–strain curve of a short-fiber-reinforced composite in tension. A shear lag model is developed for the tensile stress–strain response of short-fiber-reinforced composites allowing for an elastic-perfectly plastic stress transfer. Composites with different fiber volume fractions and a variable content of plasticizer have been analyzed. The apparent IFSS of flax/starch acetate is within the range of 5.5–20.5 MPa, de…
Flexural bearing capacity and related ductility demand for masonry sections under nonlinear constitutive law
2003
This paper aims at examining the maximum bearing capacity of rectangular masonry cross-sections subjected to eccentric compression, by assuming a nonlinear constitutive law characterized by two parameters defining stress-strain curve of the material. The variation of these parameters permits us to represent a wide variety of materials; therefore the ductility required of these materials in order for a section to achieve the maximum bending moment compatible with an average normal stress is also determined. The proposed approach can be utilized to evaluate the safety condition of masonry bearing walls, like those characterizing buildings of historical and/or monumental interest, for which th…
Compressive behavior of short fibrous reinforced concrete members with square cross-section
2011
In the present paper a mechanical model to predict the compressive response of high strength short concrete columns with square cross-section confined by transverse steel is presented. The model allows one to estimate the equivalent confinement pressures exercised by transverse steel during the loading process taking into account of the interaction of the stirrups with the inner core both in the plane of the stirrups and in the space between two successive stirrups. The lateral pressure distributions at hoop levels are obtained by using a simple model of elastic beam on elastic medium simulating the interaction between stirrups and concrete core, including yielding of steel stirrups and dam…
Behaviour in compression of lightweight fiber reinforced concrete confined with transverse steel reinforcement
2004
Abstract The compressive behavior of lightweight fiber reinforced concrete confined with transverse reinforcement consisting of steel stirrups or spirals was analyzed. Pumice stone and expanded clay aggregates were utilized to decrease the weight of the composite; hooked steel fibers were also added. The investigation was carried out by testing cylindrical and prismatic specimens of different sizes in compression using an open-loop displacement control machine, recording the full load–deformation curves. The influence of the dimensions and shape on the bearing capacity and on the ductility of the specimens confined with transverse steel reinforcements was analyzed. The results show the poss…