Search results for "Surfaces"

Shifting the Photoresponse of ZnO Nanowires into the Visible Spectral Range by Surface Functionalization with Tailor-Made Carbon Nanodots

2018

We report on the surface functionalization of ZnO nanowires (NWs) with specifically synthesized carbon nanodots (C-dots, CDs) that allows us to shift the photoresponse of the NWs far into the visib...

Electropolishing of CuZn brasses and 316L stainless steels: Influence of alloy composition or preparation process (ALM vs. standard method)

2016

International audience; In the present paper, electropolishing behavior of different brass alloys (CuZn39Pb2, CuZn42) in phosphoric acid is studied to observe the impact of alloying elements on polishing quality. In the same way, the influence of the manufacturing process is also evaluated through the comparison of a “standard” stainless steel and a stainless steel prepared by Additive Laser Manufacturing (ALM). An electrochemical study was first performed to determine the best treatment conditions for each material/electrolyte pair and to study the electropolishing mechanism and its kinetic dependence on diffusion. Metallic samples are fully characterized before and after electropolishing …

The effect of wear on the tetragonal-to-monoclinic transformation and the residual stress distribution in zirconia-toughened alumina cutting tools

1998

Abstract Zirconia-toughened alumina cutting tools have been examined after machining an AISI 1040 steel. The Raman spectrum of zirconia and the fluorescence spectrum from alumina have been used to determine the extent of the tetragonal-to-monoclinic (t-m) transformation and the residual stresses in and around the worn-out crater, respectively. Although about 15% vol. m-zirconia is present even in a brand new cutting tool, it was shown that the crater region undergoes the t-m transformation up to 40% vol. In both cases, the transformed zone is concentrated near the surface. The residual stresses in alumina are slightly compressive in the new cutting tool and away from the crater region, but …

One step continuous hydrothermal synthesis of very fine stabilized superparamagnetic nanoparticles of magnetite

2011

International audience; Stable suspensions of citrated SPIO nanoparticles were synthesised in one step using a hydrothermal continuous process. Citrates control the crystallite size and the oxidation degree of metallic ions despite the very short reaction time (4 s). Magnetite particles, Fe2.94O4, with an average size of 4 nm and good monodispersity were obtained.

XPS and SIMS study of aluminium native oxide modifications induced by Q-switched Nd:YAG laser treatment

2006

Publié suite au congrès ECASIA: 11th European Conference on Applications of Surface and Interface Analysis, 25-30 September 2005, Vienna, Austria; International audience; During laser cleaning of aluminium in ambient atmosphere, modifications of the metal surface can be induced by transient thermal effects. This work aims to characterize the modification of the aluminium oxide layer on pure aluminium for a wide range of power per area using a Q-switched Nd :YAG (1064 nm) laser with two pulse durations, 10 and 180 ns. Experiments were carried out with single laser shots in ambient air at fluences (e.g. energy per area) below the ablation regime. For 10-ns pulses with fluences between 0.7 and…

Influence of pulp bleaching and compatibilizer selection on performance of pulp fiber reinforced PLA biocomposites

2019

Valorization of Solanum Elaeagnifolium Cavanilles Weeds as a New Lignocellulosic Source for the Formulation of Lignin-Urea-Formaldehyde Wood Adhesive

2021

Solanum Elaeagnifolium Cavanilles (SE-Cav) is an invasive plant that has been developed in Mediterranean basin countries especially in Morocco. This weeds which belongs to lignocellulosic biomass a...

Energy structure and electro-optical properties of organic layers with carbazole derivative

2014

Abstract Phosphorescent organic light emitting diodes are perspective in lighting technologies due to high efficient electroluminescence. Not only phosphorescent dyes but also host materials are important aspect to be considered in the devices where they are a problem for blue light emitting phosphorescent molecules. Carbazole derivative 3,6-di(9-carbazolyl)-9-(2-ethylhexyl)carbazole (TCz1) is a good candidate and has shown excellent results in thermally evaporated films. This paper presents the studies of electrical properties and energy structure in thin films of spin-coated TCz1 and thermally evaporated tris[2-(2,4-difluorophenyl)pyridine]iridium(III) (Ir(Fppy)3). The 0.46 eV difference …

Computer vision profilometer: equipment and evaluation of measurements

1991

Abstract This paper describes a new equipment that measures roughness values by a computer vision (CV) technique. Measurements carried out by a CV profilometer are also evaluated. A laser source (power 2 mW), a cylindrical lens and a charge coupled device (CCD) TV-camera with a suitable optical system form an image of the profile of the sample under inspection. This image is then transformed into a binary image by thresholding and the line that divides the bright zone from the dark zone is the sample profile. From this line the characteristic roughness values can be calculated. The roughness measurements are carried out both by the CV profilometer and a stylus profilometer on eight specimen…

A modular approach towards functional supramolecular aggregates - subtle structural differences inducing liquid crystallinity.

2016

Herein we report an efficient modular approach to supramolecular functional materials. Hierarchical self-assembly of azopyridine derivatives and hydrogen-bond donors yielded discotic assemblies. Subtle differences in the core units introduced mesomorphic behaviour and fast photo-response of the liquid crystals based on phloroglucinol. The presented results prove the benefits of a modular methodology towards highly responsive materials with tailor-made properties.