Search results for "TAZ"
showing 10 items of 2702 documents
Rapid evaluation of notch stress intensity factors using the peak stress method with 3D tetrahedral finite element models: Comparison of commercial c…
2022
The peak stress method (PSM) allows a rapid application of the notch stress intensity factor (NSIF) approach to the fatigue life assessment of welded structures, by employing the linear elastic peak stresses evaluated by FE analyses with coarse meshes. Because of the widespread adoption of 3D modeling of large and complex structures in the industry, the PSM has recently been boosted by including four-node and ten-node tetrahedral elements of Ansys FE software, which allows to discretize complex geometries. In this paper, a Round Robin among eleven Italian Universities has been performed to calibrate the PSM with seven different commercial FE software packages. Several 3D mode I, II and III …
Generalised bisection method for optimum ultrasonic ray tracing and focusing in multi-layered structures
2021
Ultrasonic testing has been used for many decades, proving itself very efficient for detecting defects in many industrial sectors. The desire to apply ultrasonic testing to geometrically complex structures, and to anisotropic, inhomogeneous materials, together with the advent of more powerful electronics and software, is constantly pushing the applicability of ultrasonic waves to their limits. General ray tracing models, suitable for calculating the proper incident angle of single element probes and the proper time delay of phased array, are currently required. They can support the development of new imaging techniques, as Full Matrix Capture and Total Focusing Method, and the execution of …
Laser Ultrasonics Inspection for Defect Evaluation on Train Wheel
2019
Abstract Passengers’ safety and in-service life of wheelset axles play an important role in railway vehicles. For this reason, periodic inspections are necessary. Among non-destructive techniques, ultrasonic ones are widely applied in this field. The main disadvantage of conventional ultrasonic techniques is that the overall inspection of wheels requires the train to be put out-of-service and disassembly each part, which is time-consuming and expensive. In this paper, a non-conventional non-contact laser ultrasonic inspection for train wheels is proposed. The proposed method uses a laser interferometer to receive the ultrasonic wave without contact. The receiving system allows choosing the …
Evaluation of Vertical Fatigue Cracks by Means of Flying Laser Thermography
2019
The present paper proposes a new procedure to analyze the temperature field distribution during Flying Laser Spot and Laser Line Thermographic scanning (FLST, FLLT) of metallic components, in order to detect vertical surface cracks. The methodology exploits the changes in the temperature field produced by a vertical crack, acting as a barrier towards heat diffusion, when the laser approaches the defect. A number of small regions of interests (ROIs) is placed nearby and around the laser source. The average temperature from each ROI is then monitored during the laser scanning. Vertical cracks can be detected by analyzing and comparing the temperature fluctuations from each ROI when the laser …
Analysis of 7Be and 210Pb concentration and 7Be/210Pb activity ratio in ground level air in Palermo (Italy)
2019
A series of measurements of particulate samples collected on paper filters in Palermo (Italy) during 1995–2005 has been performed to detect 210Pb air activity concentration and, along with previous similar data on 7Be, to evaluate their activity ratio. Average values for the daily activity concentrations of 7Be and 210Pb are found to be 4.7 and 0.6 mBq/m3 , respectively, 9.8 being the average activity ratio. Data confirm a seasonal behavior for both radionuclides. A correlation between 7Be and 210Pb air activity concentrations seems to exist, despite their different origins. The time behaviors of both 7Be and 210Pb air concentrations and 7Be/ 210Pb activity ratio have been compared with som…
Silicon dosimeters based on Floating Gate Sensor: design, implementation and characterization
2020
A rad-hard monolithic dosimeter has been implemented and characterized in a standard 180 nm CMOS technology. The radiation sensor (C-sensor) is based on a Floating Gate (FG) MOS discharge principle. The output current is processed by a current-to-voltage (I/V) interface and then converted by a 5-bit flash ADC. The dosimeter is re-usable (FG can be recharged) and can detect a dose up to 1krad (Si) with a resolution of 30rad (Si) typical over temperature 0 to 85°C range. The ADC allows easy further signal processing for calibration and averaging, etc. The power consumption of C-sensor plus I/V interface is < 2mW from a 5 V power supply. The overall layout area is less than 0.25mm2. The Rad…
Demosponge EST sequencing reveals a complex genetic toolkit of the simplest metazoans.
2010
Sponges (Porifera) are among the simplest living and the earliest branching metazoans. They hold a pivotal role for studying genome evolution of the entire metazoan branch, both as an outgroup to Eumetazoa and as the closest branching phylum to the common ancestor of all multicellular animals (Urmetazoa). In order to assess the transcription inventory of sponges, we sequenced expressed sequence tag libraries of two demosponge species, Suberites domuncula and Lubomirskia baicalensis, and systematically analyzed the assembled sponge transcripts against their homologs from complete proteomes of six well-characterized metazoans--Nematostella vectensis, Caenorhabditis elegans, Drosophila melanog…
Improvement of Raw Milk Cheese Hygiene through the Selection of Starter and Non-Starter Lactic Acid Bacteria: The Successful Case of PDO Pecorino Sic…
2021
This review article focuses on the technological aspects and microbiological critical points of pressed-cooked cheeses processed from raw ewe’s milk without the inoculation of starter cultures, in particular “Pecorino” cheese typology produced in Italy. After showing the composition of the biofilms adhering to the surface of the traditional dairy equipment (mainly wooden vat used to collect milk) and the microbiological characteristics of PDO Pecorino Siciliano cheese manufactured throughout Sicily, this cheese is taken as a case study to develop a strategy to improve its hygienic and safety characteristics. Basically, the natural lactic acid bacterial populations of fresh and ripened chees…
Guidance for the risk assessment of the presence at low level of genetically modified plant material in imported food and feed under Regulation (EC) …
2017
Abstract This document provides guidance for the risk assessment under Regulation (EC) No 1829/2003 of the unintended, adventitious or technically unavoidable presence in food and feed of low level of genetically modified plant material intended for markets other than in the European Union. In this context, the presence at low level is defined to be maximum 0.9% of genetically modified plant material per ingredient. This guidance is intended to assist applicants by indicating which scientific requirements of Annex II of Regulation (EU) No 503/2013 are considered necessary for the risk assessment of the presence at low levels of genetically modified plant material in food and feed.
Smart sensing and adaptive reasoning for enabling industrial robots with interactive human-robot capabilities in dynamic environments — a case study
2019
Traditional industry is seeing an increasing demand for more autonomous and flexible manufacturing in unstructured settings, a shift away from the fixed, isolated workspaces where robots perform predefined actions repetitively. This work presents a case study in which a robotic manipulator, namely a KUKA KR90 R3100, is provided with smart sensing capabilities such as vision and adaptive reasoning for real-time collision avoidance and online path planning in dynamically-changing environments. A machine vision module based on low-cost cameras and color detection in the hue, saturation, value (HSV) space is developed to make the robot aware of its changing environment. Therefore, this vision a…