Search results for "Titanium"
showing 10 items of 878 documents
Luminescence of X-ray induced radiation defects in modified lithium orthosilicate pebbles with additions of titanium dioxide
2017
The authors greatly acknowledge the technical and experimental support of O. Leys, M. H. H. Kolb, and R. Knitter (Karlsruhe Institute of Technology, Germany). The work is performed in the frames of the University of Latvia financed project No. Y9-B044-ZF-N-300, “Nano, Quantum Technologies, and Innovative Materials for Economics”.
Growth of titanium oxynitride layers by short pulsed Nd:YAG laser treatment of Ti plates: Influence of the cumulated laser fluence.
2009
International audience; Titanium oxynitride layerswere formed by surface laser treatment of Ti plates in air using a Nd:YAG laser source of short pulse duration about 5 ns. The cumulated laser fluence was varied in the 100–1200 J cm2 range and its influence on the composition and the structure of the formed layers was studied by different characterization techniques providing physico-chemical and structural information. It was shown that the laser treatment induces the insertion of light elements as O, N and C in the formed layer with the amount increasing with the laser fluence. The in-depth composition of the layers and the co-existence of different phases were also studied. The way in wh…
Conductimetry and impedance spectroscopy study of low pressure metal organic chemical vapor deposition TiN O films as a function of the growth temper…
2001
Abstract Titanium oxinitride thin films have been grown by low pressure metal organic chemical vapor deposition (LP-MOCVD) using titanium isopropoxide, Ti(OCH(CH 3 ) 2 ) 4 (TIP) and NH 3 precursors in a growth temperature range from 450 to 750°C on sapphire substrates. The electrical behaviour of these films was studied between 400 and 173 K, revealing three different behaviours, ranking from a hopping conductivity (450–500°C) to a conducting one (700–750°C), with a dual behaviour for the intermediate growth temperatures. Moreover, at room temperature, both conductimetry and impedance spectroscopy highlighted a percolation behaviour, interpreted in terms of continuum percolation. The effect…
Wavelength influence on nitrogen insertion into titanium by nanosecond pulsed laser irradiation in air
2013
Abstract We studied in this work the influence of the wavelength (532 vs. 1064 nm) on the insertion of nitrogen in titanium targets by surface laser treatments in air. The laser pulses were of 5 ns and the irradiance was lower than 25 × 10 12 W/m 2 . Results obtained using a frequency-doubled Nd:YAG laser at 532 nm were compared with those previously reported for laser treatments at 1064 nm. Nuclear reaction analysis and micro-Raman spectroscopy were used for determining the composition and the structure of the surface layers, respectively. Results showed the lower efficiency of irradiation at 532 nm for nitrogen insertion, which is possible only above threshold conditions depending on bot…
XPS analysis of sol-gel-generated mixed-oxide layers for biomedical application
2002
The excellent biocompatibility of titanium and its alloys is associated with the properties of their dense TiO2 layer on the surface. The adsorption of proteins of the body fluid to implant surfaces depends on the properties of the surface oxide layer, especially the electronic structure. Therefore, tailoring of the oxide layer is a method for influencing protein adsorption. In this study, titanium platelets are coated by the sol–gel process with mixed oxides containing the biocompatible elements Ti, Nb, Zr and Ta. In order to verify the composition of the produced oxide layer, which can differ from the adjusted precursor composition in the sol because of different reactivities of the precu…
Temperature and substrate influence on the structure of TiN O thin films grown by low pressure metal organic chemical vapour deposition
2000
Abstract This paper presents the growth and characterization of titanium oxinitride (TiN x O y ) films grown by low pressure metal organic chemical vapour deposition (LP-MOCVD). The film nitrogen content, obtained by Rutherford backscattering spectroscopy (RBS), increases as the growth temperature increases (from 23 at.% at 450°C to 46 at.% at 750°C). Below 550°C, the films do not show any X-ray diffraction pattern. Above 550°C, the deposited films present the (111) and (200) TiN textures. Films deposited on (100) Si exhibit a 2 θ shift to higher Bragg angles, depending on the N/O ratio. These shifts are explained by using a substitutional oxygen model. Moreover, the atomic structure of suc…
Mesenchymal stem cell proliferation and differentiation on load-bearing trabecular Nitinol scaffolds.
2013
Bone tissue regeneration in load-bearing regions of the body requires high-strength porous scaffolds capable of supporting angiogenesis and osteogenesis. 70% porous Nitinol (NiTi) scaffolds with a regular 3-D architecture resembling trabecular bone were produced from Ni foams using an original reactive vapor infiltration technique. The "trabecular Nitinol" scaffolds possessed a high compressive strength of 79 MPa and high permeability of 6.9×10(-6) cm2. The scaffolds were further modified to produce a near Ni-free surface layer and evaluated in terms of Ni ion release and human mesenchymal stem cell (hMSC) proliferation (AlamarBlue), differentiation (alkaline phosphatase activity, ALP) and …
Reversible oxidation of WOx and MoOx nano phases
2012
International audience; WOx and MoOx nano phases were prepared on TiO2(1 1 0) surfaces by a CVD procedure consisting of adsorption and decomposition of W(CO)(6) or Mo(CO)(6) precursors followed by annealing under UHV. Metal amount involved in each elaborated sample is in the fractional range from 0.1 to 0.35 equivalent monolayer (eqML) of W or Mo. Evolution of sample stoichiometry as a function of subsequent treatment is followed by valence band and core level photoemission as well as work function measurement. In each case, exposure of samples to molecular oxygen at room temperature induces an increase of sample work function in a range of several tenth of eV. Such a work function change i…
Electrochemical Studies of Nonstoichiometric TiO<sub>2-x</sub> Ceramic
2014
TiO2 ceramic was prepared using extrusion technology and thermal treatment in two stages: sintering in air and subsequent annealing under high vacuum conditions. Sample thermal treatment in high vacuum conditions causes formation of nonstoichiometric titanium oxide ceramic. As a result electrical conductivity of the material significantly increases. Such a material can be used for electrode production for electrochemical water treatment.
Shape memory NiTi thin films deposited at low temperature
1999
Abstract NiTi shape memory alloy (SMA) thin films have the potential to become high performance actuators for micro-electromechanical systems. Low temperature crystallized NiTi films would ensure a good compatibility with microelectronic processes and polymers. To avoid the drawbacks induced by annealing, we have tried to obtain low temperature crystallized RF sputtered NiTi films by optimising deposition parameters. We have found that NiTi films containing an excess of Ti (∼52%) were crystallized when deposited on Si(100) substrates heated up to only 473 K. NiTi/Si(n) Schottky diodes I–V characteristics showed a temperature dependence indicating structural transition in the NiTi electrode.…