Search results for "ULTRASOUND"
showing 10 items of 1259 documents
Delamination of 2D coordination polymers : the role of solvent and ultrasound
2019
Two novel cadmium-based 2D coordination polymers have been synthesized and characterized. Experimental results evidence that the best delamination processes occurs when weak interactions dominate the cohesion between layers and solvent molecules are occluded within the crystalline network. In this case, the delamination of the crystals occurs spontaneously in water. On top of that, and thanks to the high stability of the resulting (flake) colloidal dispersions, we have completed a detailed study of the sonication assisted delamination impact by: I) comparison of two different sonication approaches (bath vs. tip sonication) and II) optimization of final flake morphology and yield by controll…
Response charactterization of ammonium tartrate solid state pellets for ESR dosimetry with radiotherapeutic photon and electron beams.
2001
Solid state pellets (1 mm thick) for electron spin resonance (ESR) dosimetry were made using ammonium tartrate as the radiation-sensitive substance. Their behaviour was experimentally investigated as a function of dose with 60Co gamma rays. The calibration function obtained permits measurements of absorbed dose in the 2-50 Gy range, with a combined uncertainty of +/-4%. The lowest detectable dose was about 0.5 Gy. These properties are comparable with or even better than those of ESR dosimeters made from other materials. The time stability of the ESR signal of ammonium tartrate dosimeters at different storage conditions after irradiation was studied. A rather complex behaviour was observed, …
Coded excitation speeds up the detection of the fundamental flexural guided wave in coated tubes
2016
The fundamental flexural guided wave (FFGW) permits ultrasonic assessment of the wall thickness of solid waveguides, such as tubes or, e.g., long cortical bones. Recently, an optical non-contact method was proposed for ultrasound excitation and detection with the aim of facilitating the FFGW reception by suppressing the interfering modes from the soft coating. This technique suffers from low SNR and requires iterative physical scanning across the source-receiver distance for 2D-FFT analysis. This means that SNR improvement achieved by temporal averaging becomes time-consuming (several minutes) which reduces the applicability of the technique, especially in time-critical applications such as…
Ultrasonic detection by photo-EMF sensor and by wideband air-coupled transducer
2004
Two non-contact remote ultrasonic detection systems are compared. The first consists of a continuous wave (CW) Nd:YVO4 laser operating at 532 nm used in conjunction with a photo-induced electromotive-force (EMF) sensor. The second system employs an air-coupled capacitance transducer that has a bandwidth from 100 kHz up to 2 MHz. Both systems exhibit higher sensitivity to out-of-plane than in-plane measurements of stress wave signals. Ultrasound generation is carried out by an Nd:YAG pulsed laser at 532 nm in the thermoelastic regime in a 1.6 mm aluminum plate. A0 Lamb mode is generated at frequency-thickness product with strong out-of-plane displacements. Ultrasonic waveforms acquired are r…
Phased laser diode array permits selective excitation of ultrasonic guided waves in coated bone-mimicking tubes
2017
This paper validates simulation predictions, which state that specific modes could be enhanced in quantitative ultrasonic bone testing. Tunable selection of ultrasonic guided wave excitation is useful in non-destructive testing since it permits the mediation of energy into diagnostically useful modes while reducing the energy mediated into disturbing contributions. For instance, it is often challenging to distinguish and extract the useful modes from ultrasound signals measured in bone covered by a soft tissue. We show that a laser diode array can selectively excite ultrasound in bone mimicking phantoms. A fiber-coupled diode array (4 elements) illuminated two solid tubes (2-3mm wall thickn…
RADICAL DISTRIBUTIONS IN AMMONIUM TARTRATE SINGLE CRYSTALS EXPOSED TO PHOTON AND NEUTRON BEAMS
2014
The radiation therapy carried out by means of heavy charged particles (such as carbon ions) and neutrons is rapidly becoming widespread worldwide. The success of these radiation therapies relies on the high density of energy released by these particles or by secondary particles produced after primary interaction with matter. The biological damages produced by ionising radiations in tissues and cells depend more properly on the energy released per unit pathlength, which is the linear energy transfer and which determines the radiation quality. To improve the therapy effectiveness, it is necessary to grasp the mechanisms of free radical production and distribution after irradiation with these …
Study of the glow curves of TLD exposed to thermal neutrons.
2007
The glow curves of thermoluminescent dosimeters (TLD600, TLD700 and MCP), exposed to a mixed field of thermal neutrons and gamma photons are analysed. The fluence values of thermal neutrons used, comparable with those used in radiotherapy, allow one to define the reliability of the TLDs, in particular the most sensitive MCP, in this radiation field and to get information on the dose absorbed values. The glow curves obtained have been deconvoluted using general order kinetics and the observed differences for the different LET components have been analysed. In particular, the ratio of the n(0) parameter of two different peaks seems to allow to discriminate the different contributions of neutr…
Modeling the influence of mineral content and porosity on ultrasound parameters in bone by using synthetic phantoms
1999
Model composite media − 10×15×80 mm3 bone tissue phantoms based on an epoxy resin with fillers—were made to study the influence of porosity and mineral content on ultrasound velocity and attenuation. The pores were simulated by ∼ 1 mm3 particles of a soft rubber, while the mineral content was imitated by a mineral residue of natural bone obtained by burning and grinding. The porosity and mineral content were varied in the range of 0–70% by volume with a step of 10%. The velocity, attenuation, and prevalent frequency of ultrasound were measured by the pulse transition method, using transducers with nominal frequencies 0.1, 0.2, 0.5, and 1.0 MHz. It was experimentally found that the ultrasoun…
Relation between bone quality values from ultrasound transmission velocity and implant stability parameters--an ex vivo study.
2011
Aim The objective of this study was to determine the relationship between bone qualities measured by ultrasound transmission velocity (UTV) and primary implant stability parameters measured by radiofrequency analysis (RFA) and push-out test (POT) in an ex-vivo model. Materials and methods Three blocks of fresh porcine bone samples were obtained from different anatomic regions, correlating to cortical, mixed and cancellous bone. Mechanical bone qualities of these samples were measured using UTV (expressed in m/s) prior to implantation. Three similar implants (4.1 × 11 mm, AstraTech OS) were inserted into each of the procured bone blocks. The evaluation of implant-bone interface stability was…
Speckle correlation technique to determine roughness in the dermatologic interval.
1988
A non-invasive method is proposed to determine human skin roughness. The technique is based on measurement of the correlation between two field distributions scattered by a metallised triafol (cellulose acetate foil) replica of the epidermal area to be analysed. The two speckle patterns are produced from the same rough surface illuminated by two coherent plane waves (He-Ne laser) under two slightly different angles. The accuracy of the method is highlighted by measurements made on a set of standard samples with roughnesses previously determined by mechanical profilometry. Analysis of the results indicates a precision of around 10%, and an applicability within the interest range of very roug…