Search results for "Ultrasonic sensor"
showing 10 items of 139 documents
Intentional weld defect process: From manufacturing by robotic welding machine to inspection using TFM phased array
2019
Specimens with intentionally embedded weld defects or flaws can be employed for training, development and research into procedures for mechanical property evaluation and structural integrity assessment. It is critical that the artificial defects are a realistic representation of the flaws produced by welding. Cylindrical holes, which are usually machined after welding, are not realistic enough for our purposes as it is known that they are easier to detect than the naturally occurring imperfections and cracks. Furthermore, it is usually impractical to machine a defect in a location similar to where the real weld defects are found. For example, electro-discharge machining can prod…
Quantification of Plasma Sprayed Coating Adhesion Using Pulsed Laser Induced Decohesion Technique
2001
Abstract The aim of the present study is to compare a laser ultrasonic technique with a conventional indentation test for the determination of intrinsic properties and the adhesion of alumina coatings, of different thicknesses (30–350 µm), deposited on stainless steel substrates by atmospheric plasma spraying (APS). For this purpose, a pulsed Nd:YAG laser is used to irradiate the coated specimens, and the ultrasonic waves generated by the laser are recorded at the epicenter using a laser interferometer. In the thermoelastic regime, the good agreement between the experiment and computation allows determination of the longitudinal wave velocity as well as the Young's modulus of the oxide coat…
In-process calibration of a non-destructive testing system used for in-process inspection of multi-pass welding
2020
Abstract In multi-pass welding, there is increasing motivation to move towards in-process defect detection to enable real-time repair; thus avoiding deposition of more layers over a defective weld pass. All defect detection techniques require a consistent and repeatable approach to calibration to ensure that measured defect sizing is accurate. Conventional approaches to calibration employ fixed test blocks with known defect sizes, however, this methodology can lead to incorrect sizing when considering complex geometries, materials with challenging microstructure, and the significant thermal gradients present in materials during the inter-pass inspection period. To circumvent these challenge…
Ultrasonic tomographic analysis for getting information on the mechanical structure of ceramic tiles
2009
Influence of cavity preparation technique (rotary vs. ultrasonic) on microleakage and marginal fit of six end-root filling materials
2010
Objectives: To evaluate in vitro the effect of cavity preparation with microburs and diamond-coated ultrasonic tips on the microleakage and marginal fit of six end-root filling materials. Study Design. The following materials were assessed: amalgam (Amalcap), zinc oxide eugenol (IRM), glass ionomer (Vitrebond), compomer (Cavalite), mineral particle aggregate (MTA) and composite (Clearfil). Cavity preparation was performed with microburs or diamond ultrasonic tips in single-root teeth. The seal was evaluated in two experiments: a microleakage assay on the passage of dye to the interface; and a scanning electron microscopy study and analysis of epoxy resin replicas, measuring the size of gaps…
Numerical analysis of the influence of ultrasonic vibration on crystallization processes
2011
The challenge in the future fabrication of semiconductor bulk crystals is the improvement of the crystal quality with a simultaneous increase of the yield. For that, a proper control of mass transfer within the fluid phase is required. Besides the damping of violent convective fluctuations, the thickness of the diffusion boundary layer, causing morphological instability, has to be decreased. The influence of ultrasound in molten Germanium was analyzed by numerical simulations. The simulations were provided by applying commercial software packages ANSYS ® and FLUENT ® . ANSYS ® was used to model the ultrasonic wave propagation in the whole growth system consisting of melt and crystal, crucib…
Contributions regarding chemical composition variation in ultrasonic field overlaying welding
2016
Paper presents a new reconditioning method based on ultrasonic field and analyses the modificated structure composition in three zone: filler material, thermal influenced zone, and base material. Also, chemical composition variation as a result of ultrasonic wave influence is studied besides the ultrasonic wave influence on dilution process.
Coded excitation speeds up the detection of the fundamental flexural guided wave in coated tubes
2016
The fundamental flexural guided wave (FFGW) permits ultrasonic assessment of the wall thickness of solid waveguides, such as tubes or, e.g., long cortical bones. Recently, an optical non-contact method was proposed for ultrasound excitation and detection with the aim of facilitating the FFGW reception by suppressing the interfering modes from the soft coating. This technique suffers from low SNR and requires iterative physical scanning across the source-receiver distance for 2D-FFT analysis. This means that SNR improvement achieved by temporal averaging becomes time-consuming (several minutes) which reduces the applicability of the technique, especially in time-critical applications such as…
Ultrasonic detection by photo-EMF sensor and by wideband air-coupled transducer
2004
Two non-contact remote ultrasonic detection systems are compared. The first consists of a continuous wave (CW) Nd:YVO4 laser operating at 532 nm used in conjunction with a photo-induced electromotive-force (EMF) sensor. The second system employs an air-coupled capacitance transducer that has a bandwidth from 100 kHz up to 2 MHz. Both systems exhibit higher sensitivity to out-of-plane than in-plane measurements of stress wave signals. Ultrasound generation is carried out by an Nd:YAG pulsed laser at 532 nm in the thermoelastic regime in a 1.6 mm aluminum plate. A0 Lamb mode is generated at frequency-thickness product with strong out-of-plane displacements. Ultrasonic waveforms acquired are r…
Phased laser diode array permits selective excitation of ultrasonic guided waves in coated bone-mimicking tubes
2017
This paper validates simulation predictions, which state that specific modes could be enhanced in quantitative ultrasonic bone testing. Tunable selection of ultrasonic guided wave excitation is useful in non-destructive testing since it permits the mediation of energy into diagnostically useful modes while reducing the energy mediated into disturbing contributions. For instance, it is often challenging to distinguish and extract the useful modes from ultrasound signals measured in bone covered by a soft tissue. We show that a laser diode array can selectively excite ultrasound in bone mimicking phantoms. A fiber-coupled diode array (4 elements) illuminated two solid tubes (2-3mm wall thickn…