Search results for "Voltage"
showing 10 items of 934 documents
A lossless current sensing technique for flyback converters
2009
Regardless of the feedback control, almost all converters require input or output current sense for overcurrent protection. If a current mode control is implemented, high accuracy is also required. The optimal current sensing method shows the highest accuracy and the lowest power dissipation. In this paper, a lossless and accurate current sensing technique for Flyback converters is proposed. An RC network is parallel connected with the primary MOSFET and the voltage signal across the sense capacitor accurately reproduces the magnetizing current waveform. The RC technique benefits from all the advantages of the most common current sensing techniques currently applied to Flyback converters, a…
Physically-consistent parameterization in the modeling of solar photovoltaic devices
2011
This research tests the standard one-diode model of a crystalline-Si photovoltaic cell, focusing on the physical accuracy. In particular, the (apparent) shunt resistance and the diode ideality factor are studied. Current-voltage characteristics of illuminated crystalline-Si photovoltaic modules are analyzed, and some limits of applicability of the standard model are given. Typical values of the ideality factor for crystalline-Si devices are derived from own experimental data as well as from recently published literature. It is shown that the contribution of the apparent shunt resistance is only significant for cell voltages below about 0.45 V, and depends on irradiance. This result is consi…
A prototypal PCB board for the EMI characterization of SiC-based innovative switching devices
2020
In this paper, a preliminary PCB board for the electromagnetic interference (EMI) characterization of innovative silicon-carbide (SiC) based switching devices is presented. Packaging technological issues can determine hurdles in the high-frequency switching and high power regime where wide band gap semiconductors are intended today for Electric Vehicle (EV) applications. In particular, the parasitic inductances that emerge in such devices, must be assessed, by using e.g. EMI techniques. In this specific case, the EMI characterization is supposed to be carried out in a semi-anechoic chamber, available at the University of Palermo (UNIPA), to assess the electromagnetic disturbances according …
Performances of the Fault Decoupling Device when unbalanced and multiple faults occur on distribution systems.
2005
Nowadays industrial processes are largely based on electronic devices such as programmable logic controllers and adjustable speed drives. Consequently, industrial equipments became less tolerant towards power supply disturbances. Voltage dips due to faults are surely among the worst disturbances for industrial equipments. A paper machine can be affected by disturbances of only 10% voltage drop lasting for 100 ms. A voltage dip of 75% (of the nominal voltage) with a duration shorter than 100 ms results in material loss in the range of thousands of US Dollars for semiconductors industry [1].
Type V collagen-induced upregulation of capn2 (large subunit of m-calpain) gene expression and DNA fragmentation in 8701-BC breast cancer cells
2011
Abstract Type V collagen is known to be over-deposited in the stroma of ductal infiltrating carcinomas of the breast. When used as a substrate, type V collagen restrains growth and invasion, and affects gene expression of 8701-BC ductal infiltrating carcinomas cells. Here we supplement existing data by demonstrating type V collagen dependent upregulation of capn2 gene expression in 8701-BC cells through differential display-PCR and Western blot assays. Furthermore, we suggest that our data obtained by centrifugal sedimentation and electrophoresis strongly suggest a correlation between calpain overproduction and DNA fragmentation, since the incubation with calpain inhibitor partly reverts th…
Efficient Monolithic Perovskite/Perovskite Tandem Solar Cells
2016
Thin-film solar cells suffer from various types of recombination, of which leakage current usually dominates at lower voltages. Herein, we demonstrate first a three-order reduction of the shunt loss mechanism in planar methylammonium lead iodide perovskite solar cells by replacing the commonly used hole transport layer poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) with a better hole-selective polyarylamine. As a result, these cells exhibit superior operation under reduced light conditions, which we demonstrate for the extreme case of moonlight irradiance, at which open-circuit voltages of 530 mV can still be obtained. By the shunt removal we also observe the VOC to dro…
Anthracene Based Conjugated Polymers: Correlation between π−π-Stacking Ability, Photophysical Properties, Charge Carrier Mobility, and Photovoltaic P…
2010
This article reports on the synthesis, characterization and properties of a series of anthracene−containing poly(p-phenylene-ethynylene)-alt-poly(p-phenylene-vinylene)s (PPE−PPV) copolymers with general constitutional unit (Ph−C≡C−Anthr−C≡C−Ph−CH═CH−Ph−CH═CH−)n denoted AnE-PV. Solely linear (AnE-PVaa, -ad, -ae) and solely branched (AnE-PVbb) as well as mixed linear and branched (AnE-PVab, -ac, -ba, -cc) alkoxy side chains were grafted to the backbone in order to tune the π−π-stacking ability of the materials. It has been possible to establish a correlation between π−π-stacking ability, absorptive behavior, charge carrier mobility, solar cell active layer nanoscale morphology and resulting p…
Inverted Solution Processable OLEDs Using a Metal Oxide as an Electron Injection Contact.
2007
A new type of bottom-emission electroluminescent device is described in which a metal oxide is used as the electron-injecting contact. The preparation of such a device is simple. It consists of the deposition of a thin layer of a metal oxide on top of an indium tin oxide covered glass substrate, followed by the solution processing of the light-emitting layer and subsequently the deposition of a high-workfunction (air-stable) metal anode. This architecture allows for a low-cost electroluminescent device because no rigorous encapsulation is required. Electroluminescence with a high brightness reaching 5700 cd m–2 is observed at voltages as low as 8 V, demonstrating the potential of this new a…
Persistent photovoltage in methylammonium lead iodide perovskite solar cells
2014
Open circuit voltage decay measurements are performed on methylammonium lead iodide (CH3NH3PbI3) perovskite solar cells to investigate the charge carrier recombination dynamics. The measurements are compared to the two reference polymer-fullerene bulk heterojunction solar cells based on P3HT:PC60BM and PTB7:PC70BM blends. In the perovskite devices, two very different time domains of the voltage decay are found, with a first drop on a short time scale that is similar to the organic solar cells. However, two major differences are also observed. 65-70% of the maximum photovoltage persists on much longer timescales, and the recombination dynamics are dependent on the illumination intensity.
Electrotechnologies, microwaves, and ultrasounds combined with binary mixtures of ethanol and water to extract steviol glycosides and antioxidant com…
2017
The aim of this work was to investigate the potential use of non-conventional technologies (microwaves, ultrasounds, pulsed electric fields, and high voltage electrical discharges) to enhance the extraction of high-added value compounds (mainly stevioside and rebaudioside A), and antioxidants (total phenolic compounds, flavonoids, chlorophylls, and carotenoids), from Stevia rebaudiana leaves. After treatment at equivalent energy, a supplementary diffusion was performed until 1 h. Results demonstrated that when water (100%) was used as solvent, the maximum recovery of stevioside (50.8 ± 0.1 mg/g) was obtained after ultrasound-assisted extraction, while microwave allowed the highest yields of…