Search results for "alloys"

Exploring integration prospects of opal-based photonic crystals

2003

Different methods of functionalisation of thin opal films are discussed, including synthesis of opals on pre-patterned substrates, post-synthesis electron beam lithography, preparation of opals with heterogeneous photonic band gap structure and integrating opals with light sources. These approaches have been tested experimentally and key technological problems have been identified.

Mechanical and optical properties of as-grown and thermally annealed titanium dioxide from titanium tetrachloride and water by atomic layer deposition

2021

Funding Information: This work was carried out within the MECHALD project funded by Business Finland (Tekes) and is linked to the Finnish Centers of Excellence in Atomic Layer Deposition (ref. 251220) and Nuclear and Accelerator Based Physics (refs. 213503 and 251353) of the Academy of Finland. Funding Information: This work was carried out within the MECHALD project funded by Business Finland (Tekes) and is linked to the Finnish Centers of Excellence in Atomic Layer Deposition (ref. 251220 ) and Nuclear and Accelerator Based Physics (refs. 213503 and 251353 ) of the Academy of Finland. Publisher Copyright: © 2021 The use of thin-films made by atomic layer deposition (ALD) is increasing in …

Influence of Stress on Electronic and Optical Properties of Rocksalt and Wurtzite MgO–ZnO Nanocomposites with Varying Concentrations of Magnesium and…

2022

The financial support of M-ERA.NET project “ZnMgO materials with tunable band gap for solar-blind UV sensors” (ZMOMUVS) is greatly acknowledged. The Institute of Solid State Physics, University of Latvia, as the Center of Excellence, has received funding from the European Union’s Horizon 2020 Framework Program H2020-WIDESPREAD-01-2016-2017-TeamingPhase2 under grant agreement no. 739508, project CAMART2. The calculations were performed at the Latvian SuperCluster (LASC) located at the Institute of Solid State Physics, University of Latvia.

An efficient method for selective oxidation of (oxime)Pt(II) to (oxime)Pt(IV) species using N,N-dichlorotosylamide

2016

The oxidation of (oxime)PtII species using the electrophilic chlorine-based oxidant N,N-dichlorotosylamide (4-CH3C6H4SO2NCl2) was studied. The reactions of trans-[PtCl2(oxime)2] (where oxime = acetoxime, cyclopentanone oxime, or acetaldoxime) with this oxidant led to trans-[PtCl4(oxime)2] products. The oxidation of trans-[Pt(o-OC6H4CH = NOH)2] at room temperature gave trans-[PtCl2(o-OC6H4CH = NOH)2], whereas the same reaction upon heating was accompanied by electrophilic substitution of the benzene rings. peerReviewed

Application of Broadband Dielectric Spectroscopy to Cultural Heritage: characterization and preservation of ancient paper artwork

2016

Within the cultural heritage the characterization and conservation of artworks based on paper represents a significant issue for both restorers and scientists. The paper deterioration is affected by the degree of hydrolytic and oxidative reactions which occur upon aging. Moreover, the durability of cellulose fibers depends on the intrinsic composition/structure of the paper as well as on the conservation conditions, such as temperature and humidity. The structural and dynamical characterization of the cellulose matrix and of the water confined within its pores is therefore of central interest. Our working hypothesis is that WATER DYNAMICS is one of the main determinants of paper degradation…

Clay nanotubes for paper consolidation

2014

Pickering Emulsion Gels Based on Halloysite Nanotubes and Ionic Biopolymers: Properties and Cleaning Action on Marble Surface

2019

We have fabricated ecocompatible Pickering emulsions based on halloysite nanotubes and ionic biopolymers (chitosan and pectin) from renewable resources. The effect of pectin and chitosan on the Pickering emulsion was investigated by direct visualization of the oil droplets and by the thermodynamic characterization at the interface. Pectin enhances the Pickering emulsion stability, while a phase separation and nonhomogeneous gel was observed in the presence of chitosan. We have demonstrated that the Pickering emulsion in a pectin based gel phase is suitable for wax layer removal from a marble surface. A controlled cleaning is achieved by tuning the contact time between the gel and the marble…

On the high-pressure phase stability and elastic properties ofβ-titanium alloys

2017

We have studied the compressibility and stability of different β-titanium alloys at high pressure, including binary Ti–Mo, Ti–24Nb–4Zr–8Sn (Ti2448) and Ti–36Nb–2Ta–0.3O (gum metal). We observed stability of the β phase in these alloys to 40 GPa, well into the ω phase region in the P–T diagram of pure titanium. Gum metal was pressurised above 70 GPa and forms a phase with a crystal structure similar to the η phase of pure Ti. The bulk moduli determined for the different alloys range from 97  ±  3 GPa (Ti2448) to 124  ±  6 GPa (Ti–16.8Mo–0.13O).

The Grain Boundary Wetting Phenomena in the Ti‐Containing  High‐Entropy Alloys: A Review

2021

This review is written during the preparation of M‐era.Net full proposal  ʺGrain boundaries in multicomponent alloys without principal componentʺ (A.K., A.K., G.A.L.  and E.R., application No. 9345). The Institute of Solid State Physics, University of Latvia, as a cen‐ ter of excellence, has received funding from the European Union’s Horizon 2020 Framework Pro‐ gramme H2020‐WIDESPREAD‐01‐2016‐2017‐TeamingPhase2 under grant agreement no. 739508,  project CAMART2. 

Removal of silicon from CFB-derived fly ash leachate in the context of phosphorus recovery

2018

High concentrations of dissolved silica in the acid leachate impose two major challenges on precipitation based recovery of phosphorus (P). Firstly, co-precipitation of colloidal silica in the acidic regimes decreases the purity and value of precipitated P-products. In addition, silica scaling on internal surfaces of equipment is also a problematic issue in industrial operations. Therefore, removal of dissolved silica prior to P-recovery process minimizes the risks of Si-contamination in P-products and Si-scaling. In the present study, silica removal was achieved by accelerated silica polymerization with higher acidity and ionic strength of mineral acid, which also assisted the leaching of …