Search results for "blends"

Characterization of blends with polyamide 6 and ethylene acrylic acid copolymers at different acrylic acid content

2002

In this work the morphological, calorimetric, rheological and mechanical behaviour and fourier transmission infrared analysis of blends made with polyamide 6 (PA6) and ethylene acrylic acid copolymers (EAA) containing different amount of acrylic acid were investigated. The results observed from the sample characterizations evidenced as acrylic acid cause a compatibilizing effect between polyethylene and polyamide components with modifications of blends morphology and mechanical behaviour. These effects are enhanced with increase of the acrylic acid content in the copolymer and they were attributed generally to hydrogen bond interactions among the acrylic acid group and the functional groups…

PET/PEN Blends of Industrial Interest as Barrier Materials. Part I. Many-Scale Molecular Modeling of PET/PEN Blends

2006

Mesoscale molecular simulations, based on parameters obtained through atomistic molecular dynamics and Monte Carlo calculations, have been used for modeling and predicting the behavior of PET/PEN blends. Different simulations have been performed in order to study and compare pure homopolymer blends with blends characterized by the presence of PET/PEN block copolymers acting as compatibilizer. A many-scale molecular modeling strategy was devised to evaluate PET/PEN blend characteristics, simulate phase segregation in pure PET/PEN blends, and demonstrate the improvement of miscibility due to the presence of the transesterification reaction products. The behavior of distribution densities and …

Recycling polymer blends

2014

Relaxation of photogenerated carriers in P3HT:PCBM organic blends.

2009

Relaxing in the sunlight. Long time-transient decays of photogenerated carriers in P3HT:PCBM blends for organic solar cells are interpreted in terms of the relaxation of hole carriers in a broad density of states. The after-pulse time-resolved microwave conductivity (TRMC) decays observed in P3HT:PCBM blends display a dependence on time close to t−β, independent of excitation intensity, in the 10 ns–1 μs range. This is explained in terms of the relaxation of carriers in a Gaussian density of states (DOS). The model is based on a demarcation level that moves with time by thermal release and retrapping of initially trapped carriers. The model shows that when the disorder is large the after-pu…

The Impact of Janus Nanoparticles on the Compatibilization of Immiscible Polymer Blends under Technologically Relevant Conditions

2014

Several hundred grams of Janus nanoparticles (d ≈ 40 nm) were synthesized from triblock terpolymers as compatibilizers for blending of technologically relevant polymers, PPE and SAN, on industry-scale extruders. The Janus nanoparticles (JPs) demonstrate superior compatibilization capabilities compared to the corresponding triblock terpolymer, attributed to the combined intrinsic properties, amphiphilicity and the Pickering effect. Straightforward mixing and extrusion protocols yield multiscale blend morphologies with "raspberry-like" structures of JPs-covered PPE phases in a SAN matrix. The JPs densely pack at the blend interface providing the necessary steric repulsion to suppress droplet …

Compatibilization of Polypropylene/Polyamide 6 Blend Fibers Using Photo-Oxidized Polypropylene.

2018

The use of polyamide/polyolefin blends has gained importance and concern for years, but they also show some issues to be adequately addressed, such as the incompatibility between the two components. This is usually overcome by using suitable compatibilizers, typically based on functionalized polyolefins. However, there is only little information about the use of a degraded polyolefins to induce compatibilization. This is even truer, as far as polyamide 6/polypropylene (PA6/PP) blends are concerned. In this work, compatibilization of PA6/PP blends by using small amounts of photo-oxidized PP was investigated

Reactive blending of a functionalized polyethylene with a semiflexible liquid crystalline copolyester

1996

Reactive blends (50/50 w/w) of a low molar mass polyethylene containing free carboxylic groups (PEox) and a semiflexible liquid crystalline polyester (SBH 1 : 1 : 2, by Eniricerche) have been prepared at 240 degrees C in a Brabender mixer, in the presence of Ti(OBu)(4) catalyst, for different mixing times (15, 60, and 120 min). In order to prove the formation of a PE-g-SBH copolymer, the blends have been fractionated by successive extractions with boiling toluene and xylene. The soluble fractions and the residues have been analyzed by Fourier transform infrared (FTIR) spectroscopy, thermogravimetry (TG and DTG), differential scanning calorimetry (DSC), and scanning electron microscopy (SEM)…

PREPARATION AND CHARACTERIZATION OF CLAY NANOCOMPOSITES BASED ON COMPATIBILIZED POLYAMMIDE6/POLYETHYLENE BLENDS

2008

Photo-oxidation behaviour of polyethylene/polyamide 6 blends filled with organomodified clay: Improvement of the photo-resistance through morphology …

2010

Abstract The impact of small amounts of organomodified clay (OMMT) on the photo-degradation behaviour of two blends obtained by mixing either low-density polyethylene (LDPE) or high density polyethylene (HDPE) with polyamide 6 (PA6) (LDPE/PA6 and HDPE/PA6 75/25 wt-%) was studied. The complex photo-degradation behaviour was followed by monitoring the main physical–mechanical properties of the blends. In particular, mechanical and spectroscopic tests were performed in conditions of accelerated artificial aging. An accurate mechanical and morphological characterization was previously carried out. The presence of the OMMT promotes the unexpected formation of a co-continuous morphology for the H…

Low-density polyethylene/polyamide/clay blend nanocomposites: Effect of morphology of clay on their photooxidation resistance

2017

The photooxidation behaviour of low-density polyethylene (LDPE)/polyamide (PA) blends, containing polyamide 11 (PA11) or polyamide 6 (PA6), has been investigated in the absence and presence of a small amount of commercial organomodified clay (OMMT). The polymer blends LDPE/PA11 and LDPE/PA6 at 75/25 wt./wt.%, with and without OMMT, have been prepared by a two-step procedure: extrusion and sheet formulation. The formulated complex systems have been subjected to accurate morphological analysis in order to evaluate the effect of the OMMT presence on the refinement of the blend morphology. Furthermore, the produced sheets have been subjected to arterial UVB exposure and the variations of the me…