Search results for "diamond."
showing 10 items of 232 documents
Diamond magnetometer enhanced by ferrite flux concentrators
2020
Magnetometers based on nitrogen-vacancy (NV) centers in diamond are promising room-temperature, solid-state sensors. However, their reported sensitivity to magnetic fields at low frequencies (<1 kHz) is presently >10 pT s^{1/2}, precluding potential applications in medical imaging, geoscience, and navigation. Here we show that high-permeability magnetic flux concentrators, which collect magnetic flux from a larger area and concentrate it into the diamond sensor, can be used to improve the sensitivity of diamond magnetometers. By inserting an NV-doped diamond membrane between two ferrite cones in a bowtie configuration, we realize a ~250-fold increase of the magnetic field amplitude wi…
Noncovalent force spectroscopy using wide-field optical and diamond-based magnetic imaging
2019
A realization of the force-induced remnant magnetization spectroscopy (FIRMS) technique of specific biomolecular binding is presented where detection is accomplished with wide-field optical and diamond-based magnetometry using an ensemble of nitrogen-vacancy (NV) color centers. The technique may be adapted for massively parallel screening of arrays of nanoscale samples.
Two-dimensional nuclear magnetic resonance spectroscopy with a microfluidic diamond quantum sensor
2019
Quantum sensors based on nitrogen-vacancy centers in diamond have emerged as a promising detection modality for nuclear magnetic resonance (NMR) spectroscopy owing to their micron-scale detection volume and non-inductive based detection. A remaining challenge is to realize sufficiently high spectral resolution and concentration sensitivity for multidimensional NMR analysis of picoliter sample volumes. Here, we address this challenge by spatially separating the polarization and detection phases of the experiment in a microfluidic platform. We realize a spectral resolution of 0.65 +/- 0.05 Hz, an order-of-magnitude improvement over previous diamond NMR studies. We use the platform to perform …
Continuously tunable diamond Raman laser for resonance laser ionization.
2019
We demonstrate a highly efficient, tunable, ∼5 GHz line- width diamond Raman laser operating at 479 nm. The diamond laser was pumped by a wavelength-tunable intra- cavity frequency-doubled titanium sapphire (Ti:Sapphire) laser operating at around 450 nm, at a repetition rate of 10 kHz with a pulse duration of 50 ns. The Raman reso- nator produced a continuously tunable output with high stability, high conversion efficiency (28%), and beam quality (M$^{2}$ <1.2). We also demonstrate that the linewidth and tunability of the pump laser is directly transferred to the Stokes output. Our results show that diamond Raman lasers offer great potential for spectroscopic applications, such as resonance…
Diamond Films as Support for Electrochemical Systems for Energy Conversion and Storage
2019
Many efforts have been dedicated to develop and study different catalysts supported materials for energy storage and conversion. Polymer electrolyte membranes (PEM) and capacitors have been topics of special interest for the scientific community, then, the research to find excellent catalyst-supports has constantly increased. The use of conductive diamond films has been proposed due to their mechanical and chemical stability properties. In this context, the application of BDD-catalyst surfaces for PEM fuel cells as well as the production of electrochemical capacitors using BDD materials have been summarized and discussed in this chapter.
Ab initio studies on the lattice thermal conductivity of silicon clathrate frameworks II and VIII
2016
The lattice thermal conductivities of silicon clathrate frameworks II and VIII are investigated by using ab initio lattice dynamics and iterative solution of the linearized Boltzmann transport equation(BTE) for phonons. Within the temperature range 100-350 K, the clathrate structures II and VIII were found to have lower lattice thermal conductivity values than silicon diamond structure (d-Si) by factors of 1/2 and 1/5, respectively. The main reason for the lower lattice thermal conductivity of the clathrate structure II in comparison to d-Si was found to be the harmonic phonon spectra, while in the case of the clathrate structure VIII, the difference is mainly due to the harmonic phonon spe…
Surface morphology and grain analysis of successively industrially grown amorphous hydrogenated carbon films (a-C:H) on silicon
2015
Abstract Silicon (1 0 0) has been gradually covered by amorphous hydrogenated carbon (a-C:H) films via an industrial process. Two types of these diamond-like carbon (DLC) coatings, one more flexible (f-DLC) and one more robust (r-DLC), have been investigated. Both types have been grown by a radio frequency plasma-enhanced chemical vapor deposition (RF-PECVD) technique with acetylene plasma. Surface morphologies have been studied in detail by atomic force microscopy (AFM) and Raman spectroscopy has been used to investigate the DLC structure. Both types appeared to have very similar morphology and sp 2 carbon arrangement. The average height and area for single grains have been analyzed for al…
Electrochemical treatment of real wastewater. Part 1: Effluents with low conductivity
2018
Abstract The treatment of a real wastewater characterized by low conductivity was performed by anodic oxidation at boron doped diamond (BDD) in both conventional and microfluidic cells. The electrolyses carried out in conventional cells without supporting electrolyte were characterized by very high TOC removals but excessively high energetic consumptions and operating costs. The addition of sodium sulphate, as supporting electrolyte, allowed to strongly reduce the cell potentials and consequently the energetic consumptions and the operating costs. However, under various operating conditions, the addition of Na2SO4 caused a lower removal of the TOC. The best results in terms of both TOC remo…
Cutting performance and indentation behaviour of diamond films on Co-cemented tungsten carbide
2000
Abstract Diamond films were grown by Hot Filament Chemical Vapour Deposition (HFCVD) on differently pretreated ISO-grade K10 cemented carbide (WC-5.8 wt.%Co) cutting inserts. Etching with diluted HNO3 and surface roughening by Murakami's reagent were used as substrate pretreatments. The adhesion of the films was evaluated by indentation tests. In order to obtain a reliable estimation of the adhesion by the slope of the crack radius–indentation load curves, a careful SEM measurement of the crack lengths was performed. Bare and diamond-coated cutting inserts were used for turning tests of Al2O3-reinforced aluminum alloy. The adhesion levels obtained from the indentation curves correlated well…
Nanocarbons in electrospun polymeric nanomats for tissue engineering: A review
2017
Electrospinning is a versatile process technology, exploited for the production of fibers with varying diameters, ranging from nano- to micro-scale, particularly useful for a wide range of applications. Among these, tissue engineering is particularly relevant to this technology since electrospun fibers offer topological structure features similar to the native extracellular matrix, thus providing an excellent environment for the growth of cells and tissues. Recently, nanocarbons have been emerging as promising fillers for biopolymeric nanofibrous scaffolds. In fact, they offer interesting physicochemical properties due to their small size, large surface area, high electrical conductivity an…