Search results for "ef"
showing 10 items of 32085 documents
Arsenic diffusion in relaxedSi1−xGex
2003
The intrinsic As diffusion properties have been determined in relaxed ${\mathrm{Si}}_{1\ensuremath{-}x}{\mathrm{Ge}}_{x}$ epilayers. The properties were studied as a function of composition x for the full range of materials with $x=0,$ 0.20, 0.35, 0.50, 0.65, 0.8, and 1. The activation enthalpy ${E}_{a}$ was found to drop systematically from 3.8 eV $(x=0)$ to 2.4 eV $(x=1).$ Comparisons with other impurity atom- and self-diffusion results in Si, Ge, and SiGe show that both interstitials and vacancies contribute as diffusion vehicles in the composition range $0l~xl~0.35$ and that vacancy mechanism dominates diffusion in the composition range $0.35lxl~1.$
Analysis of nonlinear time-dependent properties of carbon fiber reinforced plastic under off-axis loading
2021
Abstract Polymeric composites are rheonomic materials and their deformation can be described using the hereditary elasticity relations which allow for describing the mechanical behavior under time-variable loading with consideration of the influence of temperature and other operational factors. A system of hereditary-type constitutive relations is proposed for off-axis specimens of a unidirectional carbon fiber-reinforced plastic subjected to loading at different strain rates. Using the algebra of resolvent operators and inverted transformation, the constitutive equations allowing of description of anisotropy of rheological properties and, in particular, sensitivity to strain rates are deri…
Space Charge Measurement under DC and DC Periodic Waveform
2018
In High Voltage systems, Partial Discharges (PDs) monitoring are one of the main diagnostic instrument to evaluate the reliability of the apparatus. Under Alternating Current (AC) stress, PDs detection and recognition techniques are well consolidated. On the contrary, the monitoring of PDs under Direct Current (DC) stress is difficult due to complexities related to the nature of the phenomenon, which cause the beginning of PDs events in proximity of the dielectric breakdown. This problem has been partially overcome by using a continuous Periodic waveform (DCP) with positive average value, as described in a recent published work. Under DC stress, another degradation factor is the Space Charg…
Influence of magnetization on the applied magnetic field in various AMR regenerators
2017
International audience; The aim of this work is to assess the influence of a magnetic sample on the applied magnetic field inside the air gap of a magnetic circuit. Different magnetic sources including an electromagnet, a permanent magnet in a soft ferromagnetic toroidal yoke, as well as 2D and 3D Halbach cylinders are considered, using a numerical model. Gadolinium is chosen as magnetic material for the sample, due to its strong magnetocaloric properties and its wide use in magnetic refrigeration prototypes. We find that using uniform theoretical demagnetizing factors for cylinders or spheres results in a deviation of less than 2% in the calculation of internal magnetic fields at temperatu…
Influence of spray trajectories on characteristics of cold-sprayed copper deposits
2021
Abstract Industrial robots are widely used in cold spray (CS) as well as thermal spray to produce various coatings by precisely controlling kinematic parameters during the process. However, the robot trajectory and its effect on the characteristics of CS deposits are important, but not fully studied. This article introduces four typical spray trajectories, including zigzag path, cross path, parallel path, and spiral path, to elaborate thick CS Cu deposits, and characterizes the corresponding Cu deposits, respectively. The experimental results revealed that the spray trajectories have a major influence on the associated thermal history and the residual stress distribution. However, no signif…
Photoelectron Emission from Metal Surfaces Induced by VUV-emission of Filament Driven Hydrogen Arc Discharge Plasma
2015
Photoelectron emission measurements have been performed using a filament-driven multi-cusp arc discharge volume production H^- ion source (LIISA). It has been found that photoelectron currents obtained with Al, Cu, Mo, Ta and stainless steel (SAE 304) are on the same order of magnitude. The photoelectron currents depend linearly on the discharge power. It is shown experimentally that photoelectron emission is significant only in the short wavelength range of hydrogen spectrum due to the energy dependence of the quantum efficiency. It is estimated from the measured data that the maximum photoelectron flux from plasma chamber walls is on the order of 1 A per kW of discharge power.
Magneto-optical properties of two-layer film systems based on Fe and Cr
2020
The results of the investigation of two-layer Fe/Cr systems using the magneto-optical Kerr effect (MOKE) are presented in this paper. The samples were obtained by thermal evaporation in a vacuum with a thickness of individual layers from 2 nm to 50 nm. It was found that the presence of the Cr layer significantly affects the values of the coercivity and the Kerr angle. At a substrate temperature of 450 K, the value of the coercivity is almost half that of the same sample obtained at room temperature of the substrate. In addition, the influence of the order of deposition of layers, as well as the effect of a thin gold protective layer on the parameters measured by the Kerr method, is shown. …
B-Scan image analysis for position and shape defect definition in plates
2016
Definition of size, shape and location of defects into a mechanical component is of extreme importance in the manufacturing industry in general and particularly in high-tech applications, and in applications that can become dangerous due to the structural failure of mechanical components. In this paper, a laser-UT system has been used to define position and shape of internal defects in aluminum plates. An infrared pulsed laser is used to generate ultrasonic waves in a point of the plate and a CW laser interferometer is used as receiver to acquire the out-of-plane displacements due to the ultrasonic waves in another point of the plate. The method consists of acquiring a B-Scan map on which s…
Mechanical characterisation of pentagonal gold nanowires in three different test configurations: A comparative study.
2019
Abstract Mechanical characterisation of individual nanostructures is a challenging task and can greatly benefit from the utilisation of several alternative approaches to increase the reliability of results. In the present work, we have measured and compared the elastic modulus of five-fold twinned gold nanowires (NWs) with atomic force microscopy (AFM) indentation in three different test configurations: three-point bending with fixed ends, three-point bending with free ends and cantilevered-beam bending. The free-ends condition was realized by introducing a novel approach where the NW is placed diagonally inside an inverted pyramid chemically etched in a silicon wafer. In addition, all thre…
Interaction of carbon with microstructural defects in a W-Re matrix: An ab initio assessment
2019
The interaction of carbon atoms with point defects and the core of edge and screw dislocations with Burgers vector a 0 / 2 ⟨ 111 ⟩ in W and a W-Re matrix is studied by means of ab initio calculations. The structure and energetics of the ground-state atomic configurations are presented and rationalized. It is found that di-vacancies, which are thermally unstable in pure W according to the state-of-the-art ab initio calculations, can nucleate at C and Re-C complexes, which fill the gap in the explanation of the emergence of nanovoids observed experimentally under irradiation. Also, on the basis of the recent experimental evidence and our calculations, the temperature ranges for the manifestat…