Search results for "electronics"
showing 10 items of 4340 documents
CMOS-compatible field effect nanoscale gas-sensor: Operation and annealing models
2008
Complete modelling of electrically controlled nanoscale gas sensors with Poisson, Wolkenstein, Fokker-Planck and continuity is presented. Based on a plausible Drift explanation we developed suitable models for sensitivity control and operational modes. An onset for CMOS-complying annealing procedures is given.
Detection and monitoring of carbon monoxide using cobalt corroles film on Love wave devices with delay line configuration
2011
Among specific sensitive materials synthesized for chemical sensor development, cobalt corrole have shown attractive capabilities for CO detection [1, 2]. In this paper, we investigate the possibility to exploit such materials to develop surface acoustic wave (SAW)-based sensors. We actually demonstrate that SAW devices using delay line configuration allow investigating the molecular recognition occurring in non-conductive sensing layers of cobalt corroles. We have monitored phase variations of SAW devices versus various CO concentrations. Moreover, a specific testing setup has been developed to precisely dose CO at low concentrations, to avoid any CO leakage in the environment, to systemat…
Improvements in aggregate-paste interface by the hydration of steelmaking waste in concretes and mortars
2019
[EN] The objective of the experimental work is to study the mechanical properties in self-compacting concretes (SCC) in which part of the limestone aggregate has been replaced by granulated blast furnace slag (GBFS) in different percentages ranging from 0% to 60%. The results show that at early ages the SCC with the largest content in slag tend to have lower compressive strengths due to the poor compacting of the aggregates, although in the long-term their strength increases due to the reactivity of the slag. In fact, at the age of 365 days, the mortars made with the substitution of 50% of cement by ground GBFS reach compressive strength similar to that of the mortar made with 100% of cemen…
Achieving high effectiveQ-factors in ultra-high vacuum dynamic force microscopy
2010
The effective Q-factor of the cantilever is one of the most important figures-of-merit for a non-contact atomic force microscope (NC-AFM) operated in ultra-high vacuum (UHV). We provide a comprehensive discussion of all effects influencing the Q-factor and compare measured Q-factors to results from simulations based on the dimensions of the cantilevers. We introduce a methodology to investigate in detail how the effective Q-factor depends on the fixation technique of the cantilever. Fixation loss is identified as a most important contribution in addition to the hitherto discussed effects and we describe a strategy for avoiding fixation loss and obtaining high effective Q-factors in the forc…
Experimental evidence of high spatial confinement of elastic energy in a phononic cantilever
2021
We report on experimental high spatial confinement of elastic energy in a silicon phononic cantilever for which the quality factor of a higher-order flexural resonance is increased by a factor of 27 (from Q ∼ 80 to Q ∼ 2130) with the use of a three-row phononic crystal (PnC) strip. As shown by numerical simulations performed with the finite element method, the PnC both reduces anchor loss and confines elastic energy inside the cantilever. The PnC and the cantilever are fabricated with standard clean room techniques on a silicon on insulator substrate. Optical measurements of the out-of-plane displacements are performed with a laser scanning interferometer in a frequency range around 2 MHz.
Sensing of the Molecular Spin in Spin-Crossover Nanoparticles with Micromechanical Resonators
2019
In the past years, the use of highly sensitive silicon microelectromechanical cantilevers has been proposed as a tool to characterize the spin-crossover phenomenon by employing fast optical readout of the motion. In this work, Fe II -based spin-crossover nanoparticles of the well-known [Fe(Htrz) 2 (trz)](BF 4 ) complex wrapped with thin silica shells of different sizes will be studied by means of silicon microresonators. The silica shell will enhance its chemical stability, whereas the low thickness will allow a proper mechanical coupling between the cantilever and the spin-crossover core. To maximize the sensing of the spin-crossover phenomena, different cantilever geometries and flexural…
Variable Thickness Porous Anodic Alumina/Metal Film Bilayers for Optimization of Plasmonic Scattering by Nanoholes on Mirror
2018
Continuously variable thickness porous anodic aluminum oxide (PAAO) films were obtained using electrochemical oxidation of bulk aluminum sheet while both electrodes were simultaneously withdrawn from the electrolyte solution. The thickness gradient was controlled by the withdrawal rate (1–10 mm/min range) and thickness variation demonstrated from below 50 nm to above 1 micrometer. The thickness increased linearly with the sample lateral coordinate, whereas the nanopore structure (diameter and interpore distance) remained unchanged. Effects of the initial pore growth and capillary forces are discussed. The presented method can be used for tuning optimal PAAO thickness for optical and other a…
Experimental investigation of the cutting temperature when turning with coated indexable inserts
1999
Abstract This paper deals with an experimental investigation into the different factors which influence the temperature which occur at the coating/substrate–chip interface when machining a medium carbon steel and an austenitic stainless steel. Both flat-faced and grooved inserts coated with TiC, TiC/TiN and TiC/Al 2 O 3 /TiN were used. A standard K-type thermocouple embedded in the workpiece was used to convert measured efms to the interfacial temperature. Some optimal coating structures for high speed machining of these steels corresponding to the minimum interface temperature were selected. In particular, it was observed that by the proper selection of the thermal properties of the coatin…
Friction and wear properties of titanium and oxidised titanium in dry sliding against hardened C45 steel
2004
Abstract The aim of the paper is to present the results of conformal pin-on-disc tribological tests concerning the hard oxidised zone created in superficial layer of a titanium specimen sliding against the hardened to a hardness of 690 HV carbon C45 steel counterspecimen. Tribological testing was carried out at room temperature and at unlubricated conditions. After tests the structures and chemical compositions of the wear debris and worn surfaces were a subject of SEM and X-ray investigations. In comparison with the baseline the technical quality titanium/C45 steel couple, the wear and lifetime performance of the oxidised titanium/steel C45couple was markedly superior. Dominant wear debris…
Thermal Characterization of the Chip-Tool Interface When Using Coated Turning Inserts
2000
Abstract This paper reports some results of extensive experimental investigations of the thermal interactions between the coating/substrate and the moving surface of the chip. Semi-orthogonal cutting when bar turning a medium carbon steel and an austenitic stainless steel was carried out. Both flat-faced and grooved inserts coated with TiC, TiC/TiN, and TiC/Al 2 O 3 /TiN were tested. A standard K-type thermocouple embedded in the workpiece was used to convert measured efm's to the interfacial temperatures. In addition, the chiprake contact length and the area of contact were determined by using computer processing of scanned contact images. The minimum steady-state temperature at the interf…