Search results for "engineering.material"
showing 10 items of 2352 documents
Organic-nanoclay composite materials as removal agents for environmental decontamination
2019
Here we overview the recent advances in the fabrication of sustainable composite nanomaterials with decontamination capacity towards inorganic and organic pollutants. In this regards, we present the development of hybrid systems based on clay nanoparticles with different shapes (such as kaolinite nanosheets and halloysite nanotubes) and organic molecules (biopolymers, surfactants, cucurbituril) as efficient removal agents for both aliphatic and aromatic hydrocarbons. Due to their high specific surface area, clay nanoparticles have been successfully employed as fillers for composite membranes with excellent filtration capacity. The preparation of composite gel beads based on biopolymers (alg…
Combined Experimental and Theoretical Investigation of Heating Rate on Growth of Iron Oxide Nanoparticles
2017
Thermal decomposition is a promising route for the synthesis of highly monodisperse magnetite nanoparticles. However, the apparent simplicity of the synthesis is counterbalanced by the complex interplay of the reagents with the reaction variables that determine the final particle size and dispersity. Here, we present a combined experimental and theoretical study on the influence of the heating rate on crystal growth, size, and monodispersity of iron oxide nanoparticles. We synthesized monodisperse nanoparticles with sizes varying from 6.3 to 27 nm simply by controlling the heating rate of the reaction. The nanoparticles show size-dependent superparamagnetic behavior. Using numerical calcula…
The combined effect of refractory coatings containing reactive elements on high temperature oxidation behavior of chromia-forming alloys
2003
Abstract The high temperature oxidation behaviors of chromia-forming alloys (F17Ti and Fe–30Cr alloys) have been studied at 1273 K under isothermal conditions and at 1223 K under cyclic conditions, in air under the atmospheric pressure. To extend the oxidation lifetime, coatings have been applied onto the alloy surfaces. Al2O3 and Cr2O3 films doped with Sm2O3 or Nd2O3 were prepared via the metal-organic chemical vapor deposition technique. Single Cr2O3, Al2O3, Nd2O3 and codeposited Cr2O3–Nd2O3, Al2O3–Nd2O3, Al2O3–Sm2O3 coatings drastically improved the chromia-forming alloy high temperature oxidation behavior, since they decreased the oxidation rate and enhanced the oxide scale adhesion. Re…
One pot microwave assisted synthesis of bisphosphonate alkene capped gold nanoparticles
2014
International audience; A new synthetic pathway for the direct synthesis of water soluble gold nanoparticles (GNPs) already possessing terminal alkene functional groups was developed. This is achieved by using synthesized (1-hydroxy-1-phosphonopent-4-enyl)phosphonic acid (HMBPene), presenting advantages of the well known bisphosphonate coating applied to colloidal gold instead of metal oxides. The proposed protocol allowed an accurate control of the particle size in the 13–20 nm diameter range with a high spherical uniformity, which is a crucial point for these colloids' properties. We have shown that it is possible to synthesize a functionalized nanoplatform in a one-pot one-phase process …
Combustion of activated aluminum
2006
Abstract Combustion of activated aluminum was studied by four different methods: microscopic imaging of the preignition process, digital imaging of the combustion process at pressures up to 64 bar in air, nitrogen, and carbon dioxide, TGA, and DSC. Activation by three fundamentally different methods was found effective in enhancing both the ignitability and the burn rate. The complex fluoride coating prevented agglomeration completely in all stages of combustion, while the nickel and cobalt coatings promoted agglomeration of aluminum oxide at combustion, but prevented the agglomeration of the aluminum metal before combustion. Nickel coating catalyzed aluminum nitride formation, accelerating…
Cut-edge corrosion of a Zn–55Al-coated steel: A comparison between sulphate and chloride solutions
2011
Abstract Ex situ observations and in situ measurements of current and pH distributions over cut-edge coated steels revealed that Zn–55Al coatings are sacrificial only in chloride solutions, because of an activation of both Zn- and Al-rich phases present in the coating. In sulphate solutions, an efficient cathodic protection occurs only for short times of immersion, because only Zn-rich phases are active in this medium. The low solubility and strong acidification induced by Al(OH)SO4 allows only short distance cathodic protection, but cannot prevent red rust precipitation on the steel surface.
Insertion of Magnetic Bimetallic Oxalate Complexes into Layered Double Hydroxides
2006
Bimetallic oxalate complexes have been successfully inserted into layered double hydroxides as ferromagnetic oxalate-bridged oligomers. Different preparation methods afford different sizes and compositions for the oligomers. In all cases, no magnetic ordering has been observed above 2 K.
Iron Oxide Superparticles with Enhanced MRI Performance by Solution Phase Epitaxial Growth
2018
Organized three-dimensional (3D) nanomaterial architectures are promising candidates for applications in optoelectronics, catalysis, or theranostics owing to their anisotropy and advanced structural features that allow tailoring their physical and chemical properties. The synthesis of such complex but well-organized nanomaterials is difficult because the interplay of interfacial strain and facet-specific reactivity must be considered. Especially the magnetic anisotropy with controlled size and morphology plays a decisive role for applications like magnetic resonance imaging (MRI) and advanced data storage. We present a solution phase seed mediated synthesis of colloidal, well dispersible ir…
Tuning the Optical Absorption of Sn-, Ge-, and Zn-Substituted Cs2AgBiBr6 Double Perovskites: Structural and Electronic Effects
2021
Lead-free halide double perovskites (DPs) are highly tunable materials in terms of chemical composition and optical properties. One of the most widely reported DPs is Cs2AgBiBr6, which is envisaged as a promising absorber for photovoltaics. Nevertheless, its bandgap (around 1.9−2.3 eV) remains too large for common tandem solar cells. In this work, we report the mechanochemical synthesis of Sn-, Ge-, and Zn-substituted Cs2AgBiBr6 in powder form; their bandgaps reach 1.55, 1.80, and 2.02 eV, respectively. These differences are rationalized through density functional theory calculations, demonstrating combined electronic and structural (disorder) effects introduced by the divalent metal-cation…
CTAB Stabilizes Silver on Gold Nanorods
2020
We present a study that allows us to explain the chemical changes behind the often observed but so far ununderstood drift of the plasmon resonance of chemically prepared gold nanorods in microfluid...