Search results for "fabrication"

Tailoring the Interface of Biomaterials to Design Effective Scaffolds

2018

Tissue engineering (TE) is a multidisciplinary science, which including principles from material science, biology and medicine aims to develop biological substitutes to restore damaged tissues and organs. A major challenge in TE is the choice of suitable biomaterial to fabricate a scaffold that mimics native extracellular matrix guiding resident stem cells to regenerate the functional tissue. Ideally, the biomaterial should be tailored in order that the final scaffold would be (i) biodegradable to be gradually replaced by regenerating new tissue, (ii) mechanically similar to the tissue to regenerate, (iii) porous to allow cell growth as nutrient, oxygen and waste transport and (iv) bioactiv…

The emerging role of 3D printing in the fabrication of detection systems

2021

Abstract 3D printing is fast evolving as an additive manufacturing technique that has been adopted in (bio)analytical science because of the ample variety of materials and technologies currently available for highly affordable prototyping. This review focuses on the unique characteristics of 3D printing for manufacturing of optical and electrochemical detection systems, and sampling interfaces for analytical purposes using fused deposition modelling, vat polymerization (stereolithography and digital light processing) and photopolymer inkjet printing. The majority of works surveyed within the time span of mid-2018 to mid-2020 encompassed the fabrication of several components of the detection…

Effect of high temperature annealing (T > 1650 °C) on the morphological and electrical properties of p-type implanted 4H-SiC layers

2019

This work reports on the effect of high temperature annealing on the electrical properties of p-type implanted 4H-SiC. Ion implantations of Aluminum (Al) at different energies (30-200 keV) were carried out to achieve 300 nm thick acceptor box profiles with a concentration of about 10(20) at/cm(3). The implanted samples were annealed at high temperatures (1675-1825 degrees C). Morphological analyses of the annealed samples revealed only a slight increase of the surface roughness RMS up to 1775 degrees C, while this increase becomes more significant at 1825 degrees C (RMS = 1.2 nm). Room temperature Hall measurements resulted in a hole concentration in the range 0.65-1.34 x 10(18)/cm(3) and m…

Management of OH absorption in tellurite optical fibers and related supercontinuum generation

2013

Abstract We report the fabrication and the characterization of low OH content and low loss tellurite optical fibers. The influence of different methods of glass fabrication on fiber losses has been investigated. The use of the purest commercial raw materials can reduce the losses below 0.1 dB/m at 1.55 μm. Incorporation of fluoride ions into the tellurite glass matrix makes the optical fibers transparent up to 4 μm. A suspended core microstructured fiber has been fabricated and pumped by nanojoule-level femtosecond pulses, thus resulting in more than 2000-nm bandwidth supercontinuum after a few centimeters of propagation.

Influence of initial treatments of aluminium on the morphological features of electrochemically formed alumina membranes

2003

Abstract The fabrication of alumina membranes by electrochemical oxidation of annealed aluminium was investigated. Porous layers were grown in 0.4 M H3PO4 at −1 and 5 °C at different anodising times. The morphology of the outer surface was found to be dependent on temperature and charge density, with both determining the extent of chemical dissolution of the anodic oxide. The inner-surface morphology was found to depend on the applied voltage only. The chemical dissolution rate of anodic oxide grown on annealed aluminium was found to be lower than that formed on unannealed aluminium under otherwise identical conditions. Such a difference in behaviour is explained in terms of a higher finish…

Inkjet printing Ag nanoparticles for SERS hot spots

2018

A novel inkjet printing based approach is developed for the fabrication of a customizable platform on glass substrates allowing for surface enhanced Raman spectroscopy (SERS) detection of analytes up to single hot spots generated by the spontaneous aggregation of Ag nanoparticles (Ag NPs) in pL scale droplets. After drying the printed droplets under ambient conditions, trace amounts of the analyte can be detected by SERS given the proximity to NP hot spots. By employing alizarin (10-5M) as a model system and scaling the ink droplet volume from 1 nL to 10 pL, the absolute quantity of hot spots has been derived in the printed droplets allowing detecting up to a few molecules in proximity to i…

Ruthenium Oxide Nanotubes Via Template Electrosynthesis

2011

Ruthenium oxide nanotubes were fabricated by a single-step galvanostatic deposition using porous anodic alumina membrane as template. For the electrodeposition process, we used a electrochemical cell specifically designed in order to employ only 0.5 ml of 0.02 M RuCl3•xH2O solution. The deposition from a very small volume was specifically addressed owing to the high cost of ruthenium compounds, which could be of some relevance from an applicative point of view. Several techniques were used to characterize the samples prior to and after thermal treatment, which was carried out at different temperatures in order to study the crystallization process of the deposit. Raman spectroscopy of as-dep…

BIO-Bragg gratings: structured molecular networks for on-fiber bioanalysis

2021

The research on photonic biosensors is a scientific hot topic at the moment, with a significant potential impact on industry and medicine. Label-free, miniaturized, inexpensive and low-loss biosensors are developed based on optical fiber technology. Our approach is based on a Bio-Bragg-Grating (BBG) patterned on the surface of a microfiber. We present the design, fabrication and proof of concept of our device, as well as its multiplexing and tunability perspectives [1] .

2020

Large segmental bone defects occurring after trauma, bone tumors, infections or revision surgeries are a challenge for surgeons. The aim of our study was to develop a new biomaterial utilizing simple and cheap 3D-printing techniques. A porous polylactide (PLA) cylinder was printed and functionalized with stromal-derived factor 1 (SDF-1) or bone morphogenetic protein 7 (BMP-7) immobilized in collagen type I. Biomechanical testing proved biomechanical stability and the scaffolds were implanted into a 6 mm critical size defect in rat femur. Bone growth was observed via x-ray and after 8 weeks, bone regeneration was analyzed with µCT and histological staining methods. Development of non-unions …

Advances in Perovskite Optoelectronics: Bridging the Gap Between Laboratory and Fabrication

2020

In 2019, hybrid halide perovskites celebrated their 10th anniversary as a "wonder material" for optoelectronic applications. Although the parent perovskite structures were elucidated in the late 19th century, the seminal work by Miyasaka et al. exploiting organic‐inorganic hybrid halide perovskites sensitizers for visible‐light conversion in solar cells marked the revisit of these materials and has proven to be a game‐changer in this field. Extensive investigations were undertaken to develop new materials (all inorganic and organic‐inorganic hybrids, in the form of films or alternate morphologies) and deposition techniques, explore interfaces and in‐depth characterization, while engineering…