Search results for "inductor"
showing 10 items of 75 documents
Production and characterization of glicosidases from Aspergillus terreus using "pastazzo" as inductor .
2010
Characterization of inductors in partial saturation for SMPS applications
2017
The exploitation of partially saturated inductors in Switching Mode Power Supply (SMPS) is a key strategy for reducing the size of SMPS and increasing their power density [1]. However an accurate characterization and modellization of each inductor is needed for a correct design and control of the SMPS [2]. Most of inductors' datasheets only indicate the nominal inductance at low current. Anyway, when the inductor is subjected to a higher current, the value of the inductance is lessened. Moreover, inductance meters often actuate their measurements at no or moderate DC bias. In this work we describe the realization of an automated test bench (Fig. 1) for characterizing an inductor under varia…
Parameter identification of linear induction motor model in extended range of operation by means of input-output data
2012
This paper proposes a technique for the off-line estimation of the electrical parameters of the equivalent circuit of linear induction machines (LIM), taking into consideration the end effects, and focuses on the application of an algorithm based on the minimization of a suitable cost function involving the differences of measured and computed by simulation inductor current components. This method exploits an entire start-up transient of the LIM to estimate all the 4 electrical parameters of the machine (Rs, L s, σ Ls, Tr). It proposes also a set of tests to be made to estimate the variation of the magnetic parameters of the LIM versus the magnetizing current as well as the magnetizing curv…
On the design of a high current power supply for superconducting magnet
2002
The purpose of the article is the description, considerations of design and presentation of experimental results of a high current (1000 A) and low voltage (up to 15 V) converter for the excitement of superconducting corrector magnets in particle accelerators. The power source, which is based on a ZVT converter, presents high efficiency, small output ripple, excellent regulation of line, and fulfilment of the EMC normative (VDE 0871 A).
PCB-Based Planar Inductive Loops for Partial Discharges Detection in Power Cables
2022
Partial discharge (PD) diagnosis tests, including detecting, locating, and identifying, are used to trace defects or faults and assess the degree of aging in order to monitor the insulation condition of medium- and high-voltage power cables. In this context, an experimental evaluation of three different printed circuit board (PCB)-based inductive sensor topologies, with spiral, non-spiral, and meander shapes, is performed. The aim is to assess their capabilities for PD detection along a transmission power cable. First, simulation and experimental characterization are carried out to determine the equivalent electrical circuit and the quality factor of the three sensors. PD activity was studi…
Voltage Source Multilevel Inverters With Reduced Device Count: Topological Review and Novel Comparative Factors
2021
Multilevel inverters (MLIs) have gained increasing interest for advanced energy-conversion systems due to their features of high-quality produced waveforms, modularity, transformerless operation, voltage, and current scalability, and fault-tolerant operation. However, these merits usually come with the cost of a high number of components. Over the past few years, proposing new MLIs with a lower component count has been one of the most active topics in power electronics. The first aim of this article is to update and summarize the recently developed multilevel topologies with a reduced component count, based on their advantages, disadvantages, construction, and specific applications. Within …
Winding loss analysis and optimization of an AC inductor for a galvanically isolated PV inverter
2012
This paper describes simple treatments for fringing fields of air gaps in the core and bypass fluxes in the winding window area of an existing high frequency AC inductor used by a commercial developer of PV inverters. For this purpose, Maxwell (ANSOFT) electromagnetic software package is used for winding eddy current loss analysis. It is displayed that air gaps cause high flux strength and, therefore, induce significantly high eddy currents to the surrounded windings. Proximity effect also causes non uniform current density in the winding. Altogether, the inductor is affected by fringing fields, and proximity effect produces a very high AC resistance, consequently resulting in undesirable h…
A three domain controller for a high frequency high power four quadrant power converter for superconducting magnets
2002
The paper describes the implementation of a controller that orchestrates the functioning of three subsystems that implement a high energy converter (/spl plusmn/1500 A, /spl plusmn/15 V) that supplies a superconducting magnet to be used in particle accelerators. The performance of the whole system, in accordance to specifications, is documented with experimental results.
On the design of a multiple-output DC/DC converter for the PHI experiment on-board of solar orbiter
2013
Power converters for experiments that have to fly on board space missions (satellite, launchers, etc.) have very stringent requirements due to its use in a very harsh environment. The selection of a suitable topology is therefore not only based on standard requirements but additional more strict ones have also to be fulfilled. This work shows the design procedure followed to build the Power Converter Module (PCM) for the Polarimetric and Helioseismic Imager (SO/PHI), experiment on board the Solar Orbiter Satellite. The selected topology has been a Push-Pull, for a power level of approximately 35 W and with seven output voltages. Galvanic isolation is needed from primary to secondary, but no…
Achieving maximum power transfer in a multi-source renewable system
2014
In this paper, a multi-source DC-DC power system is proposed for renewable applications. A multi-input, single inductor power converter controlled by two interacting control loops is designed. The steady-state and small-signal analysis of the designed system is carried out. A battery-photovoltaic system is designed as an application example. Both the output voltage and maximum power point of solar panels are properly controlled to achieve high performances of the whole system. Experimental results on a 48 V laboratory prototype are presented to discuss system performances.