Search results for "kinetics"
showing 10 items of 2224 documents
Matter Transport and Corrosion Kinetics of Metals and Alloys at High Temperature
1992
Electrogeneration of Diiodoaurate in Dimethylsulfoxide on Gold Substrate and Localized Patterning
2016
International audience; A localized etching of gold surface by scanning electrochemical microscope technique is presented where a dimethylsulfoxide-based electrolyte charged with iodine is used. The electrogenerated triiodide ion at the platinum ultramicroelectrode tip (feedback mode) acts as an oxidant for gold surface. The effects of electrode diameter and the bias time have been investigated. The approach curve method was used to hold the electrode tip close to the gold surface. A scanning electron microscope is used to observe the etched gold surfaces where disk-shaped dots are generated. The diameter of these holes depends directly on the Pt electrode diameter and the bias time.
Hygrothermal ageing of reprocessed polylactide
2012
[EN] The influence of an accelerated hygrothermal ageing simulation test on a commercial PLA and its three subsequent mechanically-reprocessed materials was studied. The analysis was focused on the water diffusion kinetics and the physico-chemical changes induced by the hygrothermal degradation. Water diffusion proceeded faster than chain relaxation processes, as defined by a Case II absorption model. It was proved that the water diffusion rate decreased with subsequent reprocessing cycles and increased with higher hygrothermal ageing temperatures. Hydrolytic chain scission provoked significant molar mass decays and consequent general losses of thermal and mechanical performance. The rearra…
Anodization and anodic oxides
2018
Anodizing is a low-temperature, low-cost electrochemical process allowing for the growth, on the surface of valve metals and valve metal alloys, of anodic oxides of tunable composition and properties. This article is an overview on theoretical aspects concerning the general aspects of the kinetics of growth of barrier and porous anodic oxides and some of their present and possibly future technological applications of anodic oxides. The first part of the article is devoted to anodic oxide growth models, from Guntherschulze and Betz work (in 1934) to the more recent results on barrier and porous oxide films. The second part is focused on industrial processes to fabricate anodic oxides and the…
Crystallization kinetics of colloidal model suspensions: recent achievements and new perspectives
2014
Colloidal model systems allow studying crystallization kinetics under fairly ideal conditions with rather well characterized pair interactions and minimized external influences. In complementary approaches therefore experiment, analytic theory and simulation have been employed to study colloidal solidification in great detail. These studies were based on advanced optical methods, careful system characterization and sophisticated numerical methods. Both the effects of the type, strength and range of the pair-interaction between the colloidal particles and those of the colloid-specific polydispersity were addressed in a quantitative way. Key parameters of crystallization were derived and comp…
Investigation of the kinetics of growth of anodic oxide films on niobium by galvanostatic and tensiodynamic experiments
1990
Abstract The kinetics of growth of anodic oxide films on niobium has been investigated by interferometric methods. Tensiodynamic experiments allow the growth of the films at constant rate. Photoeffects during the growth of the films under absorbed light give additional information on the growth process.
Near-band luminescence of CdZnTe detector crystals
2012
The near-band luminescence due to both neutral donor and neutral acceptor bound excitons (D0 Ex), (A0Ex) and its phonon replicas as well as luminescence of donor-acceptor pair (DAP) and deep energy level due to undefined defect state (A band) were studied in CZT detector crystals. The near-band luminescence correlation with detector characteristics was analyzed and the results could be applied for nondestructive detector material selection. It is obtained that some parameters such as a presence and intensity of A and DAP luminescence bands, the decay kinetics in A0Ex-1LO and DAP luminescence bands, are most important characteristics for detector material characterization.
The effect of extracellular matrix proteins on the cellular response of HUVECS and HOBS after covalent immobilization onto titanium
2014
Biomimetic surface modifications are regarded as promising approach to stimulate cellular behavior at the interface of implant materials. Aim of the study was an evaluation of the cellular response of human umbilical cord cells (HUVECS) and human osteoblasts (HOBS) on titanium covalently coated with the extracellular matrix (ECM) proteins fibrinogen, collagen, laminin, and osteopontin. For the surface modification, titanium discs were first amino-functionalized by plasma polymerization of allylamine. The ECM protein conjugation was performed using the linker molecule α, ω-bis-N-hydroxysuccinimide polyethylene glycol (Di-NHS linker). For surface characterization, infrared spectroscopy and fl…
Thermomechanical properties and thermal degradation kinetics of poly(methyl methacrylate) (PMMA) and polycarbonate (PC) filled with cerium-doped yttr…
2016
This paper reports on the thermomechanical properties and thermal degradation kinetics of poly(methyl methacrylate) (PMMA) and polycarbonate (PC) composites filled with cerium-doped yttrium aluminium garnet (Ce:YAG) at different contents ranging between 0.1 and 5 wt%, and prepared by melt compounding. The interaction between PMMA and the filler was much stronger than that between PC and the filler, and this resulted in a significant improvement in the dynamic mechanical properties of the PMMA composites. The presence of filler did not significantly increase the thermal stability of the PC, while an observable increase in the thermal stability was only observed at higher filler loadings for …
Study of methyl methacrylate polymerization in the presence of rubbers
2001
Grafting of poly(methylmethacrylate) onto various unsaturated rubbers is described. The grafting is achieved through thermally initiated methylmethacrylate in-situ polymerization. The main features of the polymerization process, i.e. conversion vs. time, grafting to rubber and gel percentage, have been investigated. The chemical structure of the rubber influences the process: rubber with pendant unsaturations gives rise to higher level of grafting.