Search results for "mecA"
showing 10 items of 475 documents
Characterization process to measure the electrical contact resistance of Gas Diffusion Layers under mechanical static compressive loads
2016
AEM2016. International conference on Advanced Energy Materials, University of Surrey, Guildford, ROYAUME-UNI, 12-/09/2016 - 14/09/2016; Recent research has identified the mechanical properties of the fuel cell internal components (in particular, the Gas Diffusion Layers - GDLs) as key-parameters to obtain high final performances of the generator. The mechanical compression modulus of these components, the stability of their mechanical properties with respect to temperature and humidity, and their ability to interact with water have an impact on the electrical contact resistances in the stack and, by consequence, on the overall performance of the electric generator. Reducing the losses by co…
Pre-Stressed Sub-Surface Contribution on Bulk Diffusion in Metallic Solids
2011
Our recent modelling works and corresponding numerical simulations realized to describe the UO2 oxidation processes confirm the theory showing that an applied mechanical strain can strongly affect the local oxygen diffusion in a stressed solid. This result allows us to assume that stress field, previously applied at the surface of a metallic sample on several microns, will delay the degradation during its oxidation. Considering this hypothesis, we implemented a FEM simulation code developed in our laboratory to numerically investigate some different stress fields applied on a sample sub-surface, that might significantly modify the volume diffusion of oxygen during the oxidation process. The…
Thermal-electrical-mechanical simulation of the nickel densification by Spark Plasma Sintering. Comparison with experiments
2016
Abstract Spark Plasma Sintering is a non-conventional process of the powder metallurgy field which uses a high electrical current to rapidly produce fully dense materials. In the present paper, a thermal-electrical-mechanical model developed on ABAQUS Software is proposed to simulate the densification of a nickel disk. A compaction model, studied in [Wolff, C., Mercier, S., Couque, H., Molinari, A., 2012. Modeling of conventional hot compaction and spark plasma sintering based on modified micromechanical models of porous materials. Mechanics of Materials 49 (0), 72–91. URL http://www.sciencedirect.com/science/article/pii/S0167663611002195 ], has been used to reproduce the densification of t…
MICRO-SCALE STUDY OF RESIDUAL STRESSES IN CR2O3 COATINGS SPRAYED BY APS
2020
International audience; Whichever the application field, every material forming process generates residual stresses on the surface. While they are likely to enhance the aimed properties of the final mechanical part, these stresses may also drastically reduce them and result in early failures. Therefore, understanding the residual stress state remains a major challenge when coating complex parts, especially as most characterization methods at the microscopic scale involve specific sample preparation procedures which may affect the residual stresses field. This work investigates the residual stress state that exists in chromium oxide coatings deposited via Atmospheric Plasma Spray (APS), usin…
Mechanical properties and corrosion behaviour after scratch and tribological tests of electrodeposited Co-Mo/TiO2 nano-composite coatings
2019
International audience; The micro-mechanical (Young’s modulus and hardness) and tribological properties, as well as the scratch resistance of Co-Mo/TiO2 nano-composite coatings were investigated. The coating was found to be harder and stiffer than the substrate (pure cobalt). Low residual stresses were also derived from Stoney’s equation (type I stress). The corrosion behaviour after tribological and scratch tests was studied in Ringer’s solution. Dry sliding of the coating against an alumina ball at the load of 1 N or 2 N over the same distance had nearly no influence onthe anodic branch of the polarisation curves. By contrast, the current density in the cathodic branch (oxygen reduction r…
Epoxy composites filled with high surface area-carbon fillers
2013
Citation: J. Appl. Phys. 114, 164304 (2013); doi: 10.1063/1.4826529 (Received 24 July 2013; accepted 6 October 2013; published online 22 October 2013) A comprehensive analysis of electrical, electromagnetic (EM), mechanical, and thermal properties of epoxy resin composites filled with 0.25–2.0 wt. % of carbon additives characterized by high surface area, both nano-sized, like carbon nanotubes (CNTs) and carbon black (CBH), and micro-sized exfoliated graphite (EG), was performed. We found that the physical properties of both CNTs- and CBH-based epoxy resin composites increased all together with filler content and even more clearly for CBH than for CNTs. In the case of EG-based composites, go…
A comparative study of fatigue behaviour of flax/epoxy and glass/epoxy composites
2012
Experimental investigations on flax and glass fabrics reinforced epoxy specimens, i.e. FFRE and GFRE, submitted to fatigue tests are presented in this paper. Samples having [0/90]3S and [±45]3S stacking sequences, with similar fibre volume fractions have been tested under tension–tension fatigue loading. The specific stress-number of cycles to failure (S–N) curves, show that for the [0/90]3S specimens, FFRE have lower fatigue endurance than GFRE, but the [±45]3S FFRE specimens offer better specific fatigue endurance than similar GFRE, in the studied life range (<2 × 10^6). Overall, the three-stage stiffness degradation is observed in all cases except for [0/90]3S FFRE specimens, which prese…
Generation and characterization of T40/A5754 interfaces with lasers
2014
Laser-induced reactive wetting and brazing of T40 titanium with A5754 aluminum alloy with 1.5 mm thickness was carried out in lap-joint configuration, with or without the use of Al5Si filler wire. A 2.4 mm diameter laser spot was positioned on the aluminum side to provoke spreading and wetting of the lower titanium sheet, with relatively low scanning speeds (0.1 to 0.6 m/min). Process conditions did not play a very significant role on mechanical strengths, which were shown to reach 250-300 N/mm on a large range of laser power and scanning speeds. In all cases considered, the fracture during tensile testing occurred next to the TiAl3 interface, but in the aluminum fusion zone. In a second st…
Acoustic modes in metallic nanoparticles: atomistic versus elasticity modeling
2009
The validity of the linear elasticity theory is examined at the nanometer scale by investigating the vibrational properties of silver and gold nanoparticles whose diameters range from about 1.5 to 4 nm. Comparing the vibration modes calculated by elasticity theory and atomistic simulation based on the Embedded Atom Method, we first show that the anisotropy of the stiffness tensor in elastic calculation is essential to ensure a good agreement between elastic and atomistic models. Second, we illustrate the reduction of the number of vibration modes due to the diminution of the number of atoms when reducing the nanoparticles size. Finally, we exhibit a breakdown of the frequency-spectra scalin…
Laser densification of organic coating: Effects of laser wavelength, operating parameters and substrate properties
2012
International audience; Mechanical bonding and interface behaviour play a key role for any materials deposited on different substrates. Usually, a post-spray heat treatment is required to improve the coating morphology and to enhance mechanical properties of thermal-sprayed polymeric coating. The effects of YAG, CO2 and diode laser radiations on as-sprayed PEEK coating deposited on stainless steel and aluminum substrates were investigated. The results revealed a good coating densification and interface behavior. A correlation between coating and substrate absorption coefficients, their thermophysical properties and laser operating parameters was shown. Besides, the finite element modeling b…