Search results for "relative humidity"

Sensor response time evaluations of trace hydrogen gaseous species with platinum using Kelvin Probe

2012

Kelvin Probe (KP), a non-contact, non-destructive vibrating capacitor device, was used to measure the work function (WF) difference of thin Pt films, deposited on oxidized silicon substrates, with highly diluted H 2 gas, in ppm levels, in the presence of with and without relative humidity (RH). Response times were extracted from the behavior of WF shift as a function of H 2 concentration values. Measurements were compared for zero and non-zero RH conditions at a fixed temperature of 30°C. Changes in WF were evaluated by using HP VEE program, suitably modified for the present measurements. The events were executed step by step for every second time interval through an input formatted file. T…

Application of sol-gel and laser evaporation methods to obtain thin gas sensitive films

2005

New type resistive/capacitative gas sensitive structures were obtained by using a specially prepared substrate- glass, covered by thin conducting In/sub 2/O/sub 3/ layer, cutted into a comb teeth-type electrodes by help of laser beam. Such laser processed gap in the layer of conducting material was a prototype of excellent humidity sensor, especially at high values of relative humidity (RH). Different additional coatings onto a laser processed gap were examined for humidity sensing. Sol-gel, vacuum thermal evaporation and laser evaporation methods were used to obtain a thin layers of different materials.

Bias and humidity effects on the ammonia sensing of perylene derivative/lutetium bisphthalocyanine MSDI heterojunctions

2016

International audience; In this paper, we prepared and studied sensors based on Molecular Semiconductor-Doped Insulator (MSDI) heterojunctions. These original devices are built with two stacked layers of molecular materials and exhibit very specific electrical and sensing properties. We studied the properties of a MSDI composed of the perylenetetracarboxylic dianhydride, PTCDA, or the fluorinated perylenebisimine derivative, C4F7-PTCDI, as n-type molecular material sublayers, and LuPc2 as a p-type semiconductor top layer. Their response to ammonia was compared to that of a resistor formed of only the top layer of the MSDI (LuPc2). Ammonia increases the current in the MSDIs whereas it causes…

Humidity-Induced Grain Boundaries in MAPbI3 Perovskite Films

2016

Methylammonium lead halide perovskites (MAPbI3) are very sensitive to humid environments. We performed in situ scanning force microscopy and in situ X-ray diffraction measurements on MAPbI3 films to track changes in the film morphology and crystal structure upon repeated exposure to a high relative humidity environment (80%). We found that the appearance of monohydrate (MAPbI3·H2O) Bragg reflections coincided with the appearance of additional grain boundaries. Prolonging the exposure time to humidity induced more grain boundaries and steps in the MAPbI3 films, and the peak intensities of the monohydrate MAPbI3·H2O increased. The monohydrate was not stable under dry atmosphere and could be r…

Sensing properties of assembled Bi2S3nanowire arrays

2015

Bismuth sulfide (Bi2S3) nanowires were grown in porous aluminium oxide template and a selective chemical etching was applied to transfer the nanowires to a solution. Well aligned nanowire arrays were assembled on pre-patterned silicon substrates employing dielectrophoresis. Electron beam lithography was used to connect aligned individual nanowires to the common macroelectrode. In order to evaluate the conductometric sensing performance of the Bi2S3 nanowires, current–voltage characteristics were measured at different relative humidity (RH) levels (5–80%) / argon medium. The response of the Bi2S3 nanowires depending of RH is found to be considerably different from those reported for other ty…

Relative Humidity Dependent Resistance Switching of Bi2S3Nanowires

2017

Electrical properties of Bi2S3nanowires grown using a single source precursor in anodic aluminum oxide templates are sensitive to the relative humidity in an inert gas environment. Dynamic sensing dependency is obtained and shows presence of spontaneous resistance switching effect between low and high relative humidity states. Employing the thermionic field emission theory, heights of Schottky barriers are estimated from the current-voltage characteristics and in relation to the humidity response. The change of Schottky barrier height is explained by local changes in physically adsorbed water molecules on the surface of the nanowire.

2014

NanosizedCeO2powders were synthesized via hydrothermal method with different types of surfactants (polyethylene glycol (PEG), cetyltrimethylammonium bromide (CTAB), and sodium dodecylbenzenesulfonate (SDBS)). X-ray diffraction, Raman spectroscopy, and transmission electron microscopy were utilized to characterize the phase structures and morphologies of the products. The sample with CTAB as surfactant (CeO2-C) has the largest specific surface area and the smallest particle size among these three samples. The humidity sensor fabricated byCeO2-C shows higher performance than those usedCeO2-P andCeO2-S. The impedance of theCeO2-C sensor decreases by about five orders of magnitude with relative…

From the solution processing of hydrophilic molecules to polymer-phthalocyanine hybrid materials for ammonia sensing in high humidity atmospheres.

2014

We have prepared different hybrid polymer-phthalocyanine materials by solution processing, starting from two sulfonated phthalocyanines, s-CoPc and CuTsPc, and polyvinylpyrrolidone (PVP), polyethylene glycol (PEG), poly(acrylic acid-co-acrylamide) (PAA-AM), poly(diallyldimethylammonium chloride) (PDDA) and polyaniline (PANI) as polymers. We also studied the response to ammonia (NH3) of resistors prepared from these sensing materials. The solvent casted films, prepared from s-CoPc and PVP, PEG and PAA-AM, were highly insulating and very sensitive to the relative humidity (RH) variation. The incorporation of s-CoPc in PDDA by means of layer-by-layer (LBL) technique allowed to stabilize the fi…

A methodology to assess the effect of sweat on infrared thermography data after running: Preliminary study

2020

Abstract The aim of this technical report is to present a preliminary study carried out to define the methodology to be employed for further research on assessing the effect of sweating on infrared thermography and thermal contact sensors after moderate intensity running. Nine recreational runners participated in this preliminary study. Participants ran for 35 min (5 min warm-up and 30 min at a rate of perceived exertion rate of 12 points on the 6–20 points Borg scale). Skin temperature (infrared thermography, Flir E60bx; four thermal contact sensors, IButton DS1923 Hygrochron) and relative humidity (thermal contact sensors) were measured on the anterior thigh on both lower limbs before and…

Effect of Moisture Content on the Processing and Mechanical Properties of a Biodegradable Polyester

2021

This work is focused on the influence of moisture content on the processing and mechanical properties of a biodegradable polyester used for applications in injection molding. The pellets of the biodegradable polyester were exposed under different relative humidity conditions at a constant temperature before being compression molded. The compression-molded specimens were again placed under the above conditions before the mechanical testing. With all these samples, it is possible to determine the effect of moisture content on the processing and mechanical properties separately, as well as the combined effect of moisture content on the mechanical properties. The results obtained showed that th…