Search results for "roughness"
showing 10 items of 216 documents
Experimental Observation Of Turbulent Structures In A Straight Flume
2010
Experimental and theoretical studies of the structure of turbulence in open-channel flows have shown that the dynamics of the wall layer turbulence is dominated by the formation and growth of turbulent structures which evolve periodically as part of the so-called bursting phenomena. In the present paper experimental results obtained in a straight flume for different roughness conditions of the channel walls are described. The occurrence of turbulent events is verified by applying the conditioned quadrant analysis. The information about the spatial and temporal scales of the events is obtained through the space-time correlations of the conditioned data.
A new calibration of the effective scattering albedo and soil roughness parameters in the SMOS SM retrieval algorithm
2017
Abstract This study focuses on the calibration of the effective vegetation scattering albedo (ω) and surface soil roughness parameters (H R , and N Rp , p = H,V) in the Soil Moisture (SM) retrieval from L-band passive microwave observations using the L-band Microwave Emission of the Biosphere (L-MEB) model. In the current Soil Moisture and Ocean Salinity (SMOS) Level 2 (L2), v620, and Level 3 (L3), v300, SM retrieval algorithms, low vegetated areas are parameterized by ω = 0 and H R = 0.1, whereas values of ω = 0.06 − 0.08 and H R = 0.3 are used for forests. Several parameterizations of the vegetation and soil roughness parameters (ω, H R and N Rp , p = H,V) were tested in this study, tre…
Optimization of the straightness measurements on rough surfaces by Monte Carlo simulation
2013
Summary The straightness error of a coordinate measuring machine (CMM) is determined by measuring a rule standard. Thanks to a reversal technique, the straightness uncertainty of the CMM is theoretically dissociated from the straightness uncertainty of the rule. However, stochastic variations of the whole measurement system involve uncertainties of the CMM straightness error. To quantify these uncertainties, different sources of stochastic variations are listed with their associated probability density functions. Then Monte Carlo methods are performed first to quantify error and secondly to optimize measurement protocol. It is shown that a 5-measurement distance from 0.1 mm to each measurem…
Quartz Crystal Microbalance for Bioanalytical Applications
2001
The quartz crystal microbalance (QCM) was first introduced as a mass sensor in gas phase and in vacuum. Since oscillator circuits capable of exciting shear vibrations of quartz resonators under liquid load have been developed, the QCM became accepted as a new powerful technique to monitor adsorption processes at solid/liquid interfaces in chemical and biological research rendering the method an attractive low-cost alternative for bioanalytic applications. In the last decade, adsorption of biomolecules on functionalized surfaces turned out to be one of the paramount applications of piezoelectric transducers comprising the interaction of DNA and RNA with complementary strands, specific recogn…
Differential constraints for iteratively generated curves
2021
Roughness is a complex concept, that is multiscale, and based on the study of the local behavior of a curve or a surface in a given neighborhood. A large number of conventional statistical parameters are currently available to attempt to appreciate this concept in the different application areas that make use of it. But it is often difficult, for a given application domain or a special need, to know precisely which parameter(s) connect(s) the topography of a surface to the physical phenomena that it undergoes. We believe that a geometric characterization should be more suitable. We suggest to control roughness by exploiting the differential behavior of curves and surfaces. We are interested…
Influence of bed roughness on flow and turbulence structure around a partially-buried, isolated freshwater mussel
2023
The present study uses eddy-resolving numerical simulations to investigate how bed roughness affects flow and turbulence structure around an isolated, partially-buried mussel (Unio elongatulus) aligned with the incoming flow. The rough-bed simulations resolve the flow past the exposed part of a gravel bed, whose surface is obtained from a laboratory experiment that also provides some additional data for validation of the numerical model. Results are also discussed for the limiting case of a horizontal smooth bed. Additionally, the effects of varying the level of burial of the mussel inside the substrate and the discharge through the two mussel siphons are investigated via a set of simulatio…
Comment on “Effects of different tillage practices on the hydraulic resistance of concentrated flow on the loess plateau in China” by J. Sun et al
2020
Abstract For concentrated flows, which are characterized by small water depth and steep sloping beds, hydraulic conditions different from those typical of streams and rivers occur. In this study a new theoretically deduced flow resistance equation was tested using the experimental data by Sun et al. for three different tilled surfaces (Manual Dibbling, MD, Manual Hoeing, MH, and Contour Drilling, CD). At first, the profile parameter-relationship, which is the relationship between the velocity profile parameter Γ, the channel slope and the flow Froude number, was calibrated using rill flow data by Di Stefano et al. Then, the applicability of this relationship was tested by the measurements o…
Silver-loaded nanoparticles affect ex-vivo mechanical behavior and mineralization of dentin
2019
Background: The aim was to evaluate the effect of silver loaded nanoparticles (NPs) application on the triboscopic, crystallographic and viscoelastic properties of demineralized dentin. Polymethylmetacrylate-based NPs and Ag loaded NPs were applied on demineralized dentin. Material and Methods: Treated and untreated surfaces were probed by a nanoindenter to test viscoelasticity, and by atomic force microscopy to test nanoroughness and collagen fibril diameter. X-ray diffraction and transmission electron microscopy through selected area diffraction and bright-field imaging were also used. Results: Dentin treated with Ag-NPs attained the lowest complex modulus, and the highest tan delta value…
Digital Correlation Method Based on Micro-geometrical Texture Pattern for Strain Field Measurement
2011
International audience; Image correlation methods are widely used in experimental mechanics to obtain displacement field measurements. Currently, these methods are applied using digital images of the initial and deformed surfaces sprayed with black or white paint. Speckle patterns are then captured and the correlation is performed with a high degree of accuracy to an order of 0.01 pixels. In 3D, however, stereo-correlation leads to a lower degree of accuracy. Correlation techniques are based on the search for a sub-image (or pattern) displacement field. The work presented in this paper introduces a new correlation-based approach for 3D displacement field measurement that uses an additional …
Sequent depth ratio of B-jumps on smooth and rough beds
2013
A hydraulic B-jump has the toe section located on a positively sloping upstream channel and the roller end on a downstream horizontal channel. This paper analyses the B-jump on a rough bed, such as at the transition from a block ramp to the stilling basin. Laboratory measurements of the sequent depth were carried out using three different channel slopes for the rough bed and a single slope for the smooth bed. A solution useful for estimating the sequent depth ratio in a rectangular channel for different relative roughness and bed slope is proposed and positively tested by the present measurements. This solution can also be used to estimate the sequent depth ratio of classical hydraulic jump…