Search results for "scanning"
showing 10 items of 1808 documents
Thermal effects of continuous laser treatment on Ti-6 Al(wt%)-4V(wt%) titanium alloy
2008
A titanium alloy Ti-6 Al(wt%)-4V(wt%) was treated in air by Nd:YAG laser radiation (wavelength of 1.064 %m) in continuous mode. Targets were irradiated globally with different levels of energy (accumulated fluence) at constant power. Different focal lengths and beam displacement velocities were used. Cross section microstructural observations were carried out by scanning electron microscopy. Backscattered electron imaging reveals microstructural modifications in samples. A structural phase transformation of beta (bcc) to alpha prime (hcp) phase was observed. The depth of the transformed zone observed by phase transformation is dependent on the treatment parameters. Conformity between micros…
Effect of Growth Temperature on the Structural and Morphological Properties of MgCdO Thin Films Grown by Metal Organic Chemical Vapor Deposition
2017
II-VI oxides ternary alloys have attracted considerable interest of the scientific community due to the possibility of modulating their interesting optoelectronic properties. Despite this interest, MgCdO has been poorly studied. In this work, by using the metal organic chemical vapor deposition method at low pressure, we have analyzed the synthesis of thin films of this alloy. Thus, for a fixed metal-organic precursors content, a change from Mg1-xCdxO (Mg-rich phase) to Cd1-xMgxO (Cd-rich phase) has been induced when decreasing the growth temperature. The temperature range where both phases coexist has been particularly analyzed. Using X-ray diffraction analysis and scanning electron micros…
Power ultrasound irradiation during the alkaline etching process of the 2024 aluminium alloy
2015
Abstract Prior to any surface treatment on an aluminum alloy, a surface preparation is necessary. This commonly consists in performing an alkaline etching followed by acid deoxidizing. In this work, the use of power ultrasound irradiation during the etching step on the 2024 aluminum alloy was studied. The etching rate was estimated by weight loss, and the alkaline film formed during the etching step was characterized by glow discharge optical emission spectrometry (GDOES) and scanning electron microscope (SEM). The benefit of power ultrasound during the etching step was confirmed by pitting potential measurement in NaCl solution after a post-treatment (anodizing).
Behaviour of advanced tritium breeder pebbles under simultaneous action of accelerated electrons and high temperature
2017
The authors greatly acknowledge the technical and experimen-tal support of O. Valtenbergs and L. Avotina (Institute of Chemical Physics, University of Latvia). The work is performed in the frames of the University of Latvia financed project No. Y9-B044-ZF-N-300, “Nano, Quantum Technologies, and Innovative Materials for Eco-nomics”.
MOCVD growth of TiO2 thin films on single crystal GaAs substrates
2000
Abstract TiO 2 thin films have been grown on (100)GaAs and (111)GaAs substrates by low-pressure metal organic chemical vapour deposition (LP-MOCVD). Titanium(IV) isopropoxide, Ti{OCH(CH 3 ) 2 } 4 , was used as a precursor and TiO 2 films were obtained without an additional oxygen flux. Scanning electron microscopy (SEM) experiments have shown a well ordered rod-like crystallisation in the films grown on (100)GaAs. This ordered crystallisation was favoured by a high deposition temperature ( T d =700°C). By contrast, no distinct order was observed in the films grown on (111)GaAs substrates. X-ray diffraction patterns revealed a mainly rutile structure for the TiO 2 films deposited on (100)GaA…
Mechanism of Formation of TiO2-Doped Mullites from Heated Single-Phase Gels Investigated by Structural and Microstructural Parameters
2008
An analysis of the microstructure of TiO 2 -doped mullites prepared from monophasic gels thermally treated in the temperature range 900°-1600°C is reported. Two series of gels with nominal compositions 3(Al 2-x Ti x O 3 ) ·2(SiO 2 ) and 2(Al 2-x Ti x O 3 )·(SiO 2 ), in the range 0≤x≤0.15, were prepared. X-ray powder diffraction (XRD) and scanning electron microscopy (SEM) were used to follow the structural and textural evolution from gels to the final doped mullites. The crystallite sizes and microstrains were determined by linewidth refinements of XRD patterns using the integral breadth method of Langford and the Warren-Averbach analysis. XRD patterns showed the formation of Al 2 TiO 5 and…
Incremental lines in root cementum of human teeth: an approach to their ultrastructural nature by microscopy.
1998
In ground sections of human teeth, root cementum shows under the light microscope as alternating, almost concentric, dark and light rings. In paleontology and forensic medicine, the number of these incremental lines or annulations is used to derive the age-at-death of the individual. To find the ultrastructural features underlying these cemental annulations, we used bright-field light microscopy (LM), confocal laser scanning microscopy (CLSM), transmission electron microscopy (TEM), and electron-dispersive x-radiation (EDX) in a scanning electron microscope (SEM). Annulations visible in ground sections of about 100-μm thickness were no longer visible in semi-thin sections (thickness, 1-2 μ…
Synthesis of niobium aluminides using mechanically activated self-propagating high-temperature synthesis and mechanically activated annealing process
1999
The mechanically activated self-propagating high-temperature synthesis (MASHS) technique and the mechanically activated annealing process (M2AP) were used to produce NbAl3 intermetallic compound. The MASHS process results from the combination of two steps: first, a mechanical activation of the Nb 3Al powders mixture; second, a self-propagating high-temperature synthesis (SHS). The M2AP process also results from the combination of two steps: the first is the same; the second consists of the annealing of as-milled powders. Based on X-ray diffraction (XRD) analysis, scanning electron microscopy (SEM) and X-ray energy dispersive spectroscopy (EDXS), the as-milled powders, MASHS, and M2AP end-pr…
Room temperature electrodeposition of photoactive Cd(OH)2 nanowires
2009
Cd(OH)2 nanowires (NWs) were successfully prepared by room temperature electrogeneration of base using Cd(NO3)2 aqueous electrolyte and Anodic Alumina Membrane (AAM) as template. Cd(OH)2 films have been also deposited on tin-doped indium oxide (ITO) for comparison. SEM analysis shows high quality deposits made of closely packed nanowires (NWs) into AAM and uniform flake-like surface on ITO. XRD analysis reveals that Cd(OH)2 films on ITO are polycrystalline, while the nanowires grow along the preferential directions [100] and [110]. Photoelectrochemical measurements show that Cd(OH)2 NWs are photoactive materials with indirect and direct band gap of 2.15 and 2.75 eV, respectively. Keywords: …