Search results for "strength"
showing 10 items of 2415 documents
Dentin wettability enhancement for three irrigating solutions and their effect on push out bond strength of gutta percha / AH Plus
2014
Background: The aim of this study was to investigate the effect of wettability enhancement for 17% EDTA, 2.5% sodium hypochlorite and 7% maleic acid solutions on push out bond strength of gutta percha /AH Plus to root dentin. Materials and Methods: One hundred and eight extracted single rooted human lower premolars were instrumented up to Protaper Universal F5 then irrigated with 3ml of 2.5% NaOCl after each file. Irrigants were prepared and a pilot study for determination of Tween 80 concentration yielding the lowest surface tension value in every solution was conducted. Samples were randomly divided into a control group and two experimental groups (17% EDTA and 7% Maleate), further split …
The determinants of industrial location in Spain, 1856–1929
2012
Abstract During the 19th century, the Spanish economy went through the early stages of the industrialisation process. This process developed in parallel to the growing market integration of goods and factors as a result of the liberal reforms and the construction of the railway network, with the subsequent fall in transport costs. In that period, there were major changes in the pattern of industrial location across Spain, with an increasing spatial concentration of industrial activities between the 1850s and the Spanish Civil War (1936–39) and a deeper regional specialisation. What were the forces behind these changes? On the theoretical side, the Heckscher–Ohlin model suggests that the spa…
Experimental and analytical response of masonry elements under eccentric vertical loads
2005
The flexural behaviour of masonry rectangular cross-sections is studied in order to characterize the mechanical behaviour of structural elements under axial eccentric loads by means of a proper law. First the experimental response of walls under vertical centred loads is observed and a stress-strain law depending on two parameters is given in order to fit the experimental results. Subsequently the behaviour of walls nominally equal to the walls mentioned before is investigated under eccentric vertical loads, and the response is observed in terms of moment-curvature relation. To this point a comparison is made between the moment-curvature response obtained experimentally and the moment-curva…
Physical properties of green composites based on poly-lactic acid or Mater-Bi® filled with Posidonia Oceanica leaves
2018
Abstract This work focuses on the evaluation of Posidonia Oceanica leaves as effective reinforcing agent for ecofriendly, fully biodegradable polymer composites. Posidonia leaves were washed, ground and sieved in order to achieve two different size distributions and aspect ratios. They were then added to either a stiff or a ductile biodegradable polymer matrix, respectively poly-lactic acid (PLA) and MaterBi® (MB), at two different filler contents (10 wt% and 20 wt%). The materials were fully characterized from a spectroscopic, morphological, rheological, and mechanical point of view. In particular, the outcomes of tensile tests were statistically analyzed by using a Full Factorial Design i…
Microfluidic Fabrication of Physically Assembled Nanogels and Micrometric Fibers by Using a Hyaluronic Acid Derivative
2017
The employ of a hyaluronic acid (HA) derivative, bearing octadecyl (C18) and ethylenediamine (EDA) groups, for microfluidic fabrication of nanogels and microfibers is reported in this study. Two HA-EDA-C18 derivatives (125 and 320 kDa) having ionic strength sensitive properties are synthesized and characterized. The control of the rheological properties of HA-EDA-C18 aqueous dispersions by formation of inclusion complexes with hydroxypropyl-β-cyclodextrins (HPCD) is described. Reversibility of C18/HPCD complexation and physical crosslinking is detected in media with different ionic strength through oscillation frequency tests. HA-EDA-C18 125 kDa is employed for nanogel fabrication. Control …
Self-Ordering Secondary Structure of d- and l-Arginine-Derived Polyamidoamino Acids
2017
This paper reports on synthesis, acid–base properties and pH-dependent structuring in water of d-, l- and d,l-ARGO7, bioinspired polymers obtained by polyaddition of the corresponding arginine stereoisomers with N,N′-methylenebis(acrylamide). The circular dichroism spectra of d- and l-ARGO7 showed a peak at 228 nm and quickly and reversibly responded to pH changes, but were nearly unaffected by temperature, ionic strength, and denaturating agents. Theoretical modeling studies of L-ARGO7 showed that it assumed a folded structure. Intramolecular interactions led to transoid arrangements of the main chain reminiscent of the protein hairpin motif. Torsion angles showed a quite similar distribut…
Effect of nano zinc oxide as UV stabilizer on the weathering performance of wood-polyethylene composite
2016
Abstract In this study, the effect of using nano-sized zinc oxide (ZnO) particles on the enhancement if the degradation resistance of wood-high density polyethylene (HDPE) composite was investigated through artificial weathering. Samples with different amounts of ZnO mixing ratio (0, 1, 2, and 4 wt%) were manufactured using an internal mixer followed by compression molding. The prepared samples were then exposed to the artificial weathering process in a QUV weatherometer. The weathering behavior of samples was characterized using tensile strength, contact angle analysis, colorimetry, ATR-FTIR spectroscopy and FE-SEM. The results indicated that the amount of surfaces crack, tensile strength …
Static strength and fatigue life of optimized hybrid single lap aluminum–CFRP structural joints
2017
Hybrid bolted/bonded joints are used to assemble structural components, commonly made by carbon fiber reinforced plastics (CFRP), with aluminum frames. Hence, they have become common solutions in a number of modern structural applications in the industrial fields, as well as civil constructions. Unfortunately, due to the lack of understanding of the relationships between the multiple parameters of influence that characterize their mechanical performance, only limited improvement have been achieved so far over classical bonding approaches, in terms of static and fatigue strength. As a result, further studies are needed in order to better exploit the potential of hybrid bolted/bonded joints a…
Temporal control of xyloglucan self-assembly into layered structures by radiation-induced degradation
2016
Partially degalactosylated xyloglucan from tamarind seeds (Deg-XG) is a very appealing biopolymer for the production of in situ gelling systems at physiological temperature. In this work, we observe that the morphology of hydrogels evolves towards high degrees of structural organization with time, yielding to dense stacks of thin membranes within 24 h of incubation at 37 °C. We also explore the possibility offered by gamma irradiation of controlling the time scale of this phenomenon, the final morphology and mechanical properties of the system. Structural and molecular modifications of Deg-XG with dose are investigated by FTIR, dynamic light scattering (DLS) and rotational viscosimetry. The…
Thermoelastic Stress Analysis of modified Transverse Cut Tensile composite specimens under pure Mode II fatigue delamination
2018
The present work investigates the behaviour of a Transvers Crack Tensile (TCT) specimen undergoing fatigue loading, by means of a Thermoelastic Stress Analysis (TSA) experimental setup. The TCT is a tensile composite specimen where a number of internal layers are cut through the beam width. The presence of such transverse notch favours the formation of interlaminar Mode II delaminations, starting from the notch tips and propagating between the cut and continuous plies. In this work, a modification is adopted to the classic TCT specimen, where insert films, mimicking artificial delaminations, are laid across the notch tips. This is done with the purpose to favour a pure Mode II and a symmetr…