Search results for "tammet"
showing 10 items of 409 documents
Porphyrin Antenna-Enriched BODIPY–Thiophene Copolymer for Efficient Solar Cells
2018
International audience; Low bandgap A−π–D copolymer, P(BdP-DEHT), consisting of alternating BOronDIPYrromethene (BODIPY) and thiophene units bridged by ethynyl linkers, and its porphyrin-enriched analogue, P(BdP/Por-DEHT), were prepared, and their optical and electrochemical properties were studied. P(BdP-DEHT) exhibits strong absorption in the 500–800 nm range with an optical bandgap of 1.74 eV. On the basis of cyclic voltammetry, the highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) energy levels are evaluated to be −5.40 and −3.66 eV, respectively. After the anchoring of zinc(II) porphyrin on the BODIPY unit, P(BdP/Por-DEHT) displays broadened absor…
Photoelectrochemical monitoring of rouging and de-rouging on AISI 316L
2017
Electrochemical conditions for inducing rouging on surface of AISI 316L in quasi neutral aqueous solution are studied. Potentiostatic polarization at 0.6 V vs. SSC at pH ∼ 7 allowed growth of colourless passive films with a band gap slightly lower than that estimated for the oxide grown on the SS surface by air exposure due to chromium dissolution. Under stronger anodic polarization (UE = 1.5 V vs. SSC) coloured passive films are formed, mainly constituted by iron oxide according to their band gap (Eg = 2.0 eV). Etching in citric acid at 60 °C results to be effective in removing rouging.
Growth of polyaniline films on porous silicon layers
1993
Abstract The electrochemical deposition of electrically active polyaniline films (PANI) onto the surface of porous silicon (PS) layers formed at p- and n-type silicon wafers has been studied using cyclic voltammetry measurements and infrared spectroscopy. The process of PANI deposition is easier on the PS layers formed at n-Si wafers and essentially retarded at PS/p-Si samples, presumably due to a parallel reaction of oxygen evolution. The polymerization reaction starts at the pore bottoms and propagates towards the external surface of the PS layer. Electric conduction of PS/PANI composites is lower than of uncovered PS layers.
Anodic growth of passive layers on steel rebars in an alkaline medium simulating the concrete pores
2006
Electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV) techniques have been used to study passive layers anodically grown on steel rebars in an aqueous alkaline solution simulating the electrolyte of the concrete pores. Nyquist diagrams recorded by EIS at the different stabilization potentials show a diffusional tail at low frequencies. The analysis of the impedance measurements has been made by means of an equivalent circuit with a Warburg component and within the framework of the point defect model (PDM) theory. It is observed that the calculated concentration of vacancies is a function of the potential in accordance with the theoretical prediction of the PDM.
Physical and electrochemical properties of LiFePO4/C thin films deposited by direct current and radiofrequency magnetron sputtering
2011
Abstract In this study, LiFePO 4 /C thin films with various contents of carbon were prepared by direct current (DC), radiofrequency (RF) and combined (DC/RF) magnetron sputtering methods. Influences of the composition, morphology and microstructure on the electrochemical properties of LiFePO 4 /C thin films are investigated by studying charge–discharge curves, cyclic voltammetry and electrochemical impedance spectroscopy. Cyclic voltammogram of the LiFePO 4 /C thin film showed the typical redox reaction peaks characterizing the electrochemical lithium insertion/extraction reactions in LiFePO 4 . Obtained LiFePO 4 /C thin films have relatively high charge capacities (127 mAh g − 1 ). It was …
Ascorbic Acid determination using linear sweep voltammetry on flexible electrode modified with gold nanoparticles and reduced graphene oxide
2020
Indium tin oxide (ITO) coated on flexible polyethylene terephthalate (PET) substrate electrode was modified with reduced graphene oxide and gold nanoparticles by simple co-electrodeposition performed at -0.8 V vs SCE for 200 s. All samples were characterized by electron scan microscopy. The as prepared electrode was used as electrochemical sensor to selective detection of ascorbic acid using linear sweep voltammetry. Excellent results were obtained in a linear range from 20 to 150 µM of ascorbic acid with a limit of detection of about 3.1 µM (S/N=3.3). The sensors have a reproducibility of about 5.5% and also show high selectivity towards different interferents such as chlorine, calcium, ma…
Bending Sensors Based on Thin Films of Semitransparent Bithiophene-Fulleropyrrolidine Bisadducts
2020
In this study, a novel bithiophene‐fulleropyrrolidine bisadducts system (bis‐Th2PC 60 ) was synthesized and electropolymerized by chronoamperometry onto flexible ITO/PET substrates. The resulting semitransparent thin film was characterized by XPS, FT‐IR, cyclic voltammetry and optical techniques, confirming the good outcome of the electropolymerization process. AFM investigations permitted to highlight an inherent disordered granular morphology, in which the grain‐to‐grain separation depends upon the application of bending. The electrical resistance of the thin film was characterized as function of bending (in the range 0°‐90°), showing promising responsivity to low bending angles (10°‐30°)…
Discrimination of papers used in conservation and restoration by the means of the voltammetry of immobilized microparticles technique
2019
Herein, voltammetry of immobilized microparticles (VIMP) is employed for the discrimination of papers used in the conservation and restoration field. The electrochemical parameters are used for the discrimination of different samples coming from China, Japan and Korea. The method is based on the recording of the voltammetric response of microparticulate deposits from acetone extracts of paper samples deposited on a glassy carbon electrode in contact with 1.0 M H2SO4. The voltammetric responses attributed to the lignin and the oxidation products of the cellulose were collected and are discussed. The grouping of samples was obtained upon the application of the chemometric methods, as well as …
In-situ electrochemical atomic force microscopy study of aging of magnetron sputtered Pt-Co nanoalloy thin films during accelerated degradation test
2016
Abstract A Pt-Co nanoalloy thin film catalyst was prepared by using simultaneous magnetron sputtering of Pt and Co. The catalyst was characterized during accelerated degradation test using in-situ electrochemical atomic force microscopy complemented with ex-situ techniques such as energy dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy and synchrotron radiation photoelectron spectroscopy. The combined results gave the full step-by-step picture of the catalyst behavior during the aging test.
Characterizing archaeological bronze corrosion products intersecting electrochemical impedance measurements with voltammetry of immobilized particles
2017
Application of electrochemical impedance measurements to microparticulate deposits of copper corrosion products attached to graphite electrodes in contact with 0.10 M aqueous HClO4 electrolyte is described. The impedance measurements were sensitive to the applied potential and the amount of solid sample and were modeled taking into account the contribution of the uncovered base electrode. Several pairs of circuit elements provide monotonic variations which are able to characterize different corrosion compounds regardless the amount of microparticulate solid on the electrode. Application to a set of archaeological samples from the archaeological Roman site of Gadara (Jordan, 4th century AD) …