Search results for "thermoelectric"
showing 10 items of 188 documents
In Situ Synthesis of Conducting Polymers: A Novel Approach toward Polymer Thermoelectrics
2020
The efficient conversion of thermal energy into electricity by means of durable and scalable solid-state thermoelectric devices has been a well stablished aim. Electrically conducting polymers have...
Thermal sensor based on a polymer nanofilm
2016
In this work, we have developed a thermal sensor based on poly(3,4 ethylenedioxythiophene) (PEDOT) nanofilms as thermoelectric material. The PEDOT nanofilms have been synthesized by the electrochemical polymerization method. The thicknesses of the films were around 120 nm. The doping level of PEDOT was controlled by chemical reduction using hydrazine. The achieved Seebeck coeficient is 40 uV/K. A PEDOT nanofilm was integrated into an electronic circuit that amplifies the voltage originated from the Seebeck effect. The temperature increment produced by a fingerprint touching the film is enough to switch on a light emitting diode. Peer Reviewed
Cold-atom thermoelectrics
2013
Two coupled reservoirs of cold atoms can be used as a model system to study the thermoelectric effect. [Also see Report by Brantut et al. ]
Fine tuning of thermoelectric performance in phase-separated half-Heusler compounds
2015
Two successful recipes to enhance the thermoelectric performance, namely carrier concentration optimization and reduction of thermal conductivity, have been combined and applied to the p-type (Ti/Zr/Hf)CoSb1−xSnx system. An intrinsic micrometer-scale phase separation increases the phonon scattering and reduces the lattice thermal conductivity. A substitution of 15% Sb by Sn optimizes the electronic properties. Starting from this, further improvement of the thermoelectric properties has been achieved by a fine tuning of the Ti to Hf ratio. The microstructuring of the samples was studied in detail with high-resolution synchrotron powder X-ray diffraction and element mapping electron microscop…
Effect of anion substitution on the structural and transport properties of argyrodites Cu7PSe6−xSx
2019
Inspired by the good performance of argyrodites as ion conducting thermoelectrics and as solid electrolytes we investigated the effect of isovalent S2- substitution for Se2- in Cu7PSe6. At room temperature Cu7PSe6 crystallizes in the primitive cubic β-polymorph of the argyrodite structure and transforms to the face-centered high-temperature (HT) γ-modification above 320 K. The transition for the homologous Cu7PS6 occurs at 510 K. Promising thermoelectric and ion conducting properties are observed only in the HT modification, where the cations are mobile. Using Rietveld refinements against X-ray diffraction data the effect of isovalent S2- substitution for Se2- on the structural and transpor…
Transversal thermovoltages of (1 1 9) Bi2Sr2CaCu2O8+δ thin films on vicinal (1 1 0) SrTiO3 substrates
1997
Abstract Biaxial textured (1 1 9) oriented Bi 2 Sr 2 CaCu 2 O 8+δ thin films were fabricated by DC-Magnetron sputtering on vicinal (1 1 0) SrTiO 3 substrates. The crystal orientation and stochiometry of the films were obtained from precise X-ray diffraction measurements in four-circle geometry. According to anisotropic transport measurements, the superconducting transition temperature is approximately 47 K and the normal state resistivities along two perpendicular paths differ by a factor of 13.5. Transversal thermoelectric effects were investigated by measuring thermovoltages transverse to temperature gradients parallel to the surface normal induced by pulsed laser irradiation. At room tem…
Epitaxial growth and thermoelectric properties of TiNiSn and Zr0.5Hf0.5NiSn thin films
2011
Abstract Due to their exceptional thermoelectric properties Half-Heusler alloys like MNiSn (M = Ti,Zr,Hf) have moved into focus. The growth of single crystalline thin film TiNiSn and Zr 0.5 Hf 0.5 NiSn by dc magnetron sputtering is reported. Seebeck and resistivity measurements were performed and their dependence on epitaxial quality is shown. Seebeck coefficient, specific resistivity and power factor for Zr 0.5 Hf 0.5 NiSn at room temperature were measured to be 63 μV K − 1 , 14.1 μΩ m and 0.28 mW K − 2 m − 1 , respectively. Multilayers of TiNiSn and Zr 0.5 Hf 0.5 NiSn are promising candidates to increase the thermoelectric figure-of-merit by decreasing thermal conductivity perpendicular …
SPS-assisted preparation of the Magnéli phase WO2.90 for thermoelectric applications
2013
We describe the preparation and simultaneous consolidation of WO2.90 by spark plasma sintering (SPS). SPS allows for the direct manufacturing of large amounts of consolidated material. Synchrotron powder X-ray diffraction indicates that the material is single phase. Microstructure analysis indicates that the pellet is fully dense, allowing high-temperature thermoelectric properties to be reliably measured. The as-prepared samples of WO2.90 reach a ZT of 0.1 at 1100 K.
Short and long range order of Half-Heusler phases in (Ti,Zr,Hf)CoSb thermoelectric compounds
2016
Abstract The structural properties of (Ti,Zr,Hf)CoSb thermoelectric Half-Heusler compounds were investigated by synchrotron radiation based techniques. The short-range order, in particular the environment of the Co atoms, was studied by extended X-Ray absorption fine structure spectroscopy and the long range order by powder X-Ray diffraction. Structural models were obtained for the single phase materials TiCoSb0.85Sn0.15, ZrCoSb0.85Sn0.15, and HfCoSb0.85Sn0.15. These models were transferred for the phase-separated material Ti0.5Hf0.5CoSb0.85Sn0.15. As a result, proving that each Half-Heusler phase was well ordered, apart from the intermixing of Ti and Hf on its designated crystallographic l…
Performance of a thermoelectric module based on n-type (La0.12Sr0.88)0.95TiO3-δ and p-type Ca3Co4-xO9+δ
2020
Here, we present the performance of a thermoelectric (TE) module consisting of n-type (La0.12Sr0.88)0.95TiO3 and p-type Ca3Co4-xO9+δ materials. The main challenge in this investigation was operation of TE module in different atmosphere conditions, since n-type has its optimum TE-performance at reducing, while p-type at oxidizing conditions. The TE module was exposed to two different atmospheres and demonstrated higher stability in N2 atmosphere than in air. The maximum electrical power output decreased after 40 h when the hot side was exposed to N2 at 600 °C, while only 1 h at 400 °C in ambient air was enough to oxidize (La0.12Sr0.88)0.95TiO3 followed by a reduced electrical power output. T…