Uncertainty assessment of a membrane bioreactor model using the GLUE methodology
A mathematical model for the simulation of physical-biological organic removal by means of a membrane bioreactor (MBR) has been previously developed and tested. This paper presents an analysis of the uncertainty of the MBR model. Particularly, the research explores the applicability of the Generalised Likelihood Uncertainty Estimation (GLUE) methodology that is one of the most widely used methods for investigating the uncertainties in the hydrology and that now on is spreading in other research field. For the application of the GLUE methodology, several Monte Carlo simulations have been run varying the all model influential parameters simultaneously. The model was applied to an MBR pilot pl…
Membrane Fouling Mitigation in MBR via the Feast–Famine Strategy to Enhance PHA Production by Activated Sludge
Fouling is considered one of the main drawbacks of membrane bioreactor (MBR) technology. Among the main fouling agents, extracellular polymeric substances (EPS) are considered one of the most impactful since they cause the decrease of sludge filterability and decline of membrane flux in the long term. The present study investigated a biological strategy to reduce the membrane-fouling tendency in MBR systems. This consisted of seeding the reactor with activated sludge enriched in microorganisms with polyhydroxyalkanoate (PHA) storage ability and by imposing proper operating conditions to drive the carbon toward intracellular (PHA) rather than extracellular (EPS) accumulation. For that purpos…
Assessing Methane Emission and Economic Viability of Energy Exploitation in a Typical Sicilian Municipal Solid Waste Landfill
Sanitary landfills for municipal solid waste (MSW) represent one of the major anthropogenic source of GHGs emissions and are directly responsible of the climate changes we are facing nowadays. Indeed, the biodegradable organic matter of MSW undergoes anaerobic digestion producing the landfill gas (LFG), whose main components are CH4 and CO2. Therefore, biomethane energy exploitation in MSW landfills will reduce GHGs emission positively affecting the global warming. The aim of the present study was to assess the methane production in a Sicilian landfill by comparing the results from field measurements of methane emission and the estimates achieved by applying different mathematical models. A…
The role of fouling mechanisms in a submerged membrane bioreactor during the start-up
Estimation of methane emission by a municipal landfill: the case of Palermo
CH4 diffuse emissions from municipal solid waste landfills represent one of the most important anthropogenic source of greenhouse-gas. CH4 is produced by anaerobic biodegradation of organic matter in land-filled MSW and it constitutes the major component of landfill gas. Gas recovery is a suitable tool to effectively control CH4 emissions from landfill sites and the quantification of CH4 emissions represents a good tool to evaluate the effectiveness of biogas recovering system in reducing biogas emission. In particular, LFG emissions can be indirectly evaluated from mass balance equations between formation, recovery and oxidation of biogas in the landfill, as well as on a direct approach ba…
Start-up of a submerged membrane bioreactor with complete sludge retention
New applications in integrated fixed film activated sludge-membrane bioreactor (IFAS-MBR) systems
Abstract This chapter provides an overview on the development and application of integrated fixed film activated sludge-membrane bioreactor (IFAS-MBR) systems. IFAS-MBRs represent a novel configuration for advanced wastewater treatment, and only a few studies are available in literature. With this aim, the results of some studies on IFAS-MBR systems already published are discussed and compared in this chapter. Literature shows that the influent carbon to nitrogen ratio (C/N) strongly affects the biological process in IFAS-MBR. The organic matter removal efficiency (removed biologically) decreases from 60% to 23.5% with the decrease of influent C/N from 10 to 2 mgCOD mgTN− 1. Nitrogen remova…
High salinity slops treatment through a biofilm-MBR inoculated with halophilic bacteria
Oily wastewater generated, in amounts of millions of tons per year, by ships mainly in engine-rooms (bilge waters) and by washing oil tanks (slops) create a major disposal problem throughout the world because of the persistence and accumulation of xenobiotic compounds in the environment. The high salinity levels (up to 25.000 p.p.m.) and the pollutants concentration limit the chances of discharge into the sewer systems and address the disposal to the sea. This situation severely lowers the discharge limits for most of the “sensible” parameters, such both COD and hydrocarbons. Slops are usually treated by ASP with pretreatment of oil/water separation. There are limited investigations on the …
comparing two start-up strategies for MBRs: experimental study and mathematical modelling
Abstract The performance of a membrane bioreactor (MBR), and mechanisms of fouling formation, may differ due to the start-up. Therefore, the start-up can constitute an aspect that critically influences MBR performance during its lifespan. Indeed, the start-up can influence the mechanisms of membrane fouling, which is of paramount importance in an MBR. In order to gain insights on the effects of the start-up, both experimental and mathematical modelling studies were carried out on an MBR pilot plant. The MBR pilot plant constituted of a hollow fibre membrane module, in a submerged configuration, was fed by real wastewater. Two experimental periods were carried out, lasting 65 days each, char…
The role of EPS in fouling and foaming phenomena for a membrane bioreactor
In contraposition to conventional activated sludge processes, the foaming phenomenon in membrane bioreactor (MBR) is still in its infancy. On the other hand, although several studies have been carried out for better understanding the fouling phenomenon in MBR there are still some gaps in the up-to-date knowledge. The extracellular polymeric substances (EPSs) may have a primary role in fouling and foaming phenomena which in turn can be crucial for MBRs. The aim of this study is to detect a possible relationship that EPSs may have with fouling and foaming in an MBR for wastewater treatment. Foaming phenomenon is monitored by performing specific foam-tests: Foam Power, Scum Index, Foam Rating …
Biological Nutrient Removal and Fouling Phenomena in a University of Cape Town Membrane Bioreactor Treating High Nitrogen Loads
The behavior of a University of Cape Town (UCT) membrane bioreactor (MBR) system was investigated for use in biological nutrient removal from real wastewater. The pilot plant was in operation for a period of 165 days, during which an extensive data gathering campaign was conducted. The pilot plant was started up by inoculating it with activated sludge from a nearby wastewater treatment plant, and it was fed by real municipal wastewater characterized by high organic nitrogen concentrations attributable to discharges from industrial wastewater and sporadic landfill leachate. Carbon and biological nutrient removal processes, a sludge production process, and a membrane fouling mechanism were an…
Performance of a MBR pilot plant treating high strength wastewater subject to salinity increase: Analysis of biomass activity and fouling behaviour
Membrane bioreactors produce high quality effluents that could be suitable for reuse. However, when treating high strength wastewater subject to a salinity increase, a modification of biomass characteristics may occur. This circumstance is of importance, since it can have a significant impact in terms of biokinetic as well as fouling behaviour. The aim of the study was to evaluate the performance of a pilot plant MBR, in terms of biomass activity and membrane fouling, fed with high strength synthetic wastewater, when subject to a salinity increase. With normal salinity, the pilot plant showed high removal efficiencies and high biomass respiratory activity. On the other hand, the salinity in…
Aerobic granular sludge treating shipboard slop: Analysis of total petroleum hydrocarbons loading rates on performances and stability
Abstract The work focuses on the feasibility of treating slop with aerobic granular sludge. For this purpose, a 3.5 L granular sequencing batch reactor was activated and it was monitored for 156 days. The experimental campaign was divided into two periods, named Period I (100 days) and Period II (56 days). Total Petroleum Hydrocarbon (TPH) concentration in the slop was, on average, equal to 6.8 ± 1.5 mg L−1 and 13 ± 1.5 mg L−1 in Period I and Period II respectively. The obtained results during the first experimental period indicated that about 80 days were required to reach steady state with mature granules, when TPHs removal efficiency was approximately 90%. The results indicated that both…
A model for wastewater organic removal and fouling development in a SMBR pilot plant
The paper presents the setting up of a mathematical model for membrane bioreactor able to simulate physical-biological wastewater organic removal. The model is basically divided into two sub-models: the first sub-model is basically devoted for the simulation of the biological features and the second one for the physical processes. In particular regarding the biological aspects, the ASM concept has been employed. On the other hand, the physical processes have been modelled considering the deep-bed theory taking into account not only the effect of the physical membrane filtration but also the cake layer effect. This latter operates as a biological membrane leading to a further reduction of th…
Uncontrolled methane emissions from a MSW landfill surface: Influence of landfill features and side slopes
Sanitary landfills for Municipal Solid Waste (MSW) disposal have been identified as one of the most important anthropogenic sources of methane (CH4) emissions; in order to minimize its negative effects on the environment, landfill gas (LFG) recovery is a suitable tool to control CH4 emissions from a landfill site; further, the measurement of CH4 emissions can represent a good way to evaluate the effectiveness of LFG recovering systems. In general, LFG will escape through any faults in the landfill capping or in the LFG collection system. Indeed, some areas of the capping can be more permeable than others (e.g. portions of a side slope), especially when considering a temporarily capped zone …
Effect of chemical and biological surfactants on activated sludge of MBR system: Microscopic analysis and foam test
Abstract A bench-scale MBR unit was operated, under stressing condition, with the aim of stimulating the onset of foaming in the activated sludge. Possible synergies between synthetic surfactants in the wastewater and biological surfactants (Extra-Cellular Polymeric Substances, EPSs) were investigated by changing C/N ratio. The growth of filamentous bacteria was also discussed. The MBR unit provided satisfactory overall carbon removal overall efficiencies: in particular, synthetic surfactants were removed with efficiency higher than 90% and 95% for non-ionic and ionic surfactants, respectively. Lab investigation suggested also the importance to reduce synthetic surfactants presence entering…
Sensitivity analysis and uncertainty assessment of a SMBR model
Over the last decade new technologies are emerging even more for wastewater treatment. Among the new technologies, a recent possible solution regards membrane bioreactors (MBRs) that represent a promising alternative to conventional processes. Nowadays, the recurrence to mathematical models as reliable tools in planning as well as management issues is of growing interest in Wastewater Treatment Plants field. Regarding MBR modelling, due to the intrinsic complexity and uncertainty in some processes, basic models that can provide a holistic understanding of the technology at a fundamental level are of great necessity. Many mathematical models have been developed for modelling the MBR which ba…
Effect of C/N shock variation on the performances of a moving bed membrane bioreactor.
Abstract The effect of a sharp variation of C/N ratio in a moving bed membrane bioreactor (MB-MBR) pilot plant treating high strength wastewater has been investigated. The experimental campaign was divided into two periods, each characterized by a different C/N ratio (namely, 2.5 and 15, Period 1 and Period 2, respectively). The MB-MBR system was analyzed in terms of organic carbon removal, nitrification efficiency, biokinetic activity and fouling behavior. The results showed that the nitrification process was severely affected by lower C/N value and by high concentration of ammonia. It was noticed an extensive stress effect on the autotrophic bacteria. Furthermore, it was observed an incre…
An integrated model for physical-biological wastewater organic removal in a submerged membrane bioreactor: Model development and parameter estimation
The paper presents the setting up of a mathematical model for membrane bioreactor able to simulate physical-biological wastewater organic removal. The model is basically divided into two sub-models: the first sub-model is basically devoted for the simulation of the biological features and the second one for the physical processes. In particular regarding the biological aspects, the ASM concept has been employed. On the other hand, the physical processes have been modelled considering the deep-bed theory taking into account not only the effect of the physical membrane filtration but also the cake layer effect. This latter operates as a biological membrane leading to a further reduction of th…
Reactivation of aerobic granular sludge for the treatment of industrial shipboard slop wastewater: Effects of long-term storage on granules structure, biofilm activity and microbial community
Abstract This work reports on reactivation of aerobic granular sludge (AGS) for the treatment of industrial recalcitrant wastewater (slop wastewater) characterized by high salinity and hydrocarbons. AGS were reactivated in two reactors, R1 and R2, to treat industrial slop wastewater after a long-term storage for 12-months at 4 °C. In R1, salt-adapted mature aerobic granules were previously subjected to a step-wise increase of hydrocarbons, whereas in R2 aerobic granules were previously cultivated in presence of salinity and hydrocarbons. After a short-term reactivation period, the slop dosage caused a simultaneous decrease of granules dimensions and proteins/polysaccharides (PN/PS) ratio do…
Occurrence of Microplastics in Waste Sludge of Wastewater Treatment Plants: Comparison between Membrane Bioreactor (MBR) and Conventional Activated Sludge (CAS) Technologies.
In this study, the presence of microplastics in the sludge of three wastewater treatment plants (WWTPs) was examined. The investigated WWTPs operated based on a conventional activated sludge (CAS) process, with (W1) or without (W2) primary clarification, and a membrane bioreactor process (MBR) (W3). The microplastics (MPs) concentration in the samples of W3 was approximately 81.1 ± 4.2 × 103 particles/kg dry sludge, whereas MPs concentrations in W1 and W2 were 46.0 ± 14.8 × 103 particles/kg dry sludge and 36.0 ± 5.2 × 103 particles/kg dry sludge, respectively. Moreover, MPs mainly consisted of fragments (66–68%) in the CAS plants, whereas the fra…
Particle size distribution and biomass growth in a submerged membrane bioreactor
Submerged membrane bioreactors (MBR)associate in a single treatment unit a process ofbiological treatment and a phase of solid/liquidseparation by membrane filtration. Due to reduced membrane porosity, suspendedsolids and large amount of bacteria and virusesmay be retained in the reactor; consequently, highbiomass concentration is generally established inthe system. Indeed, this latter circumstance leadsto obtain a system able to operate with a low F/Mand high SRT and hence, as a result, a low sludgeproduction. In technical literature, the definition of fou-lants in MBR systems is a controversial task.More specifically, the influence of TSS onmixed liquor filterability has not been yet full…
Analisi di processo e dinamica della comunità batterica nel trattamento di sedimenti marini con reattori bioslurry
Nella nota sono riportati i risultati di una sperimentazione condotta mediante la messa in esercizio di un reattore bioslurry per il trattamento di sedimenti marini contaminati da idrocarburi. Sono state valutate le performance di processo in termini di rimozione di TPH (86% con velocità di rimozione massima di 36 mgTPH kg-1 d-1) congiuntamente ad altre tipologie di indagini volte ad ottenere maggiori informazioni sulla natura dei processi che si sono sviluppati nel reattore. Nello specifico, è stato utilizzato un approccio di tipo microbiologico mediante l’adozione di una tecnica di sequenziamento di nuova generazione (NGS - Next Generation Sequencing). Dall’analisi dei dati biologici è st…
Foaming in membrane bioreactors: Identification of the causes
Membrane bioreactors (MBRs) represent by now a well established alternative for wastewater treatment. Their increasing development is undoubtedly related to the several advantages that such technology is able to guarantee. Nevertheless, this technology is not exempt from operational problems; among them the foaming still represents an "open challenge" of the MBR field, due to the high complexity of phenomenon. Unfortunately, very little work has been done on the foaming in MBRs and further studies are required. Actually, there is not a distinct difference between conventional activated system and MBR: the main difference is that the MBR plants can retain most Extracellular Polymeric Substan…
The role of extracellular polymeric substances on aerobic granulation with stepwise increase of salinity
Abstract A granular sequencing batch reactor (GSBR) worked for 164 days to study the effect of salinity on aerobic granulation. The feeding had an organic loading rate (OLR) of 1.6 kg COD⋅m −3 ⋅d −1 and a gradual increase of salinity (from 0.30 to 38 g NaCl − ⋅L −1 ) to promote a biological salt-adaptation. First aggregates (average diameter ≈ 0.4 mm) appeared after 14 days. Extracellular polymeric substances (EPSs) analyses revealed that proteins were mainly higher than polysaccharides, and microorganisms metabolized EPSs as additional carbon source, mostly in feast phase, to face the energy demand for salinity adaptation. No significant worsening of organic matter removal was observed. Th…
Preliminary insights about the treatment of contaminated marine sediments by means of bioslurry reactor: Process evaluation and microbiological characterization
Abstract Contaminated marine sediments represent a critical threat towards human health and ecosystems, since they constitute a potential reservoir of toxic compounds release. In the present study, a bioslurry reactor was studied for the treatment of real marine sediments contaminated by petroleum hydrocarbons. The experimental campaign was divided in two periods: in the first period, microcosm trials were carried out to achieve useful indicators for biological hydrocarbon removal from sediments. The microcosm trials highlighted that the inoculum of halotolerant allochthonous bacteria provided the highest performance followed by autochthonous biomass. Based on the achieved results, in the s…
Comparison between ozonation and the OSA process: analysis of excess sludge reduction and biomass activity in two different pilot plants
The excess biomass produced during biological treatment of municipal wastewater represents a major issue worldwide, as its disposal implies environmental, economic and social impacts. Therefore, there has been a growing interest in developing technologies to reduce sludge production. The main proposed strategies can be categorized according to the place inside the wastewater treatment plant (WWTP) where the reduction takes place. In particular, sludge minimization can be achieved in the wastewater line as well as in the sludge line. This paper presents the results of two pilot scale systems, to evaluate their feasibility for sludge reduction and to understand their effect on biomass activit…
High salinity wastewater treatment by membrane bioreactors
Abstract This chapter reviews the state of the art regarding the use of membrane bioreactor (MBR) systems for saline wastewater treatment. In particular, a comprehensive review is presented discussing the most adopted MBR configurations for the treatment of saline wastewater. Further, the chapter discusses the main effects of salinity on the biological performance, kinetic parameters, fouling development, sludge rheological features, and greenhouse gas (GHG) production. Literature results show that there is a significant effect of the salinity (and/or salinity variations) on the biological performance and membrane filtration. Specifically, it was found that a gradual salinity increase, carr…
Modeling of perched leachate zone formation in municipal solid waste landfills.
The paper presents a 1D mathematical model for the simulation of the percolation fluxes throughout a landfill for municipal solid waste (MSW). Specifically, the model was based on mass balance equations, that enable simulation of the formation of perched leachate zones in a landfill for MSW. The model considers the landfill divided in several layers evaluating the inflow to and outflow from each layer as well as the continuous moisture distribution. The infiltration flow was evaluated by means of the Darcy’s law for an unsaturated porous medium, while the moisture distribution evaluation has been carried out on the basis of the theory of the vertically distributed unsaturated flow. The solu…
Evaluation of methane emissions from Palermo municipal landfill: Comparison between field measurements and models
Methane (CH(4)) diffuse emissions from Municipal Solid Waste (MSW) landfills represent one of the most important anthropogenic sources of greenhouse gas. CH(4) is produced by anaerobic biodegradation of organic matter in landfilled MSW and constitutes a major component of landfill gas (LFG). Gas recovery is a suitable method to effectively control CH(4) emissions from landfill sites and the quantification of CH(4) emissions represents a good tool to evaluate the effectiveness of a gas recovery system in reducing LFG emissions. In particular, LFG emissions can indirectly be evaluated from mass balance equations between LFG production, recovery and oxidation in the landfill, as well as by a d…
A Brief Review on the Resistance-in-Series Model in Membrane Bioreactors (MBRs)
The cake layer deposited on the membrane modules of membrane bioreactors (MBRs), especially under a submerged configuration, represents a relevant and fundamental mechanism deeply influencing the development of membrane fouling. It negatively affects the total resistance to filtration, while exerting a positive effect as a “pre-filter„ promoting the “dynamic membrane„ that protects the physical membrane from internal fouling. These two opposite phenomena should be properly managed, where the submerged membranes are usually subjected to a periodical cake layer removal through ordinary (permeate backwashing and air scouring) and/or irregular cleaning actions (manual ph…
Simultaneous nitrogen and organic carbon removal in aerobic granular sludge reactors operated with high dissolved oxygen concentration
Simultaneous nitrification and denitrification (SND) together with organic removal in granules is usually carried out without Dissolved Oxygen (DO) concentration control, at ‘‘low DO’’ (with a DO 7–8 mg/L, during feast and famine conditions respectively). In particular, different strategies of cultivation and several organic and nitrogen loading rate have been applied, in order to eval- uate the efficiencies in SND process without dissolved oxygen control. The results show that, even under conditions of high DO concentration, nitrogen and organic matter can be simultaneously removed, with efficiency >90%. Nevertheless, the biological conditions in the inner layer of the granule may change sig- …
erformances of a granular sequencing batch reactor (GSBR)
Influence of the Height of Municipal Solid Waste Landfill on the Formation of Perched Leachate Zones
Waste settlement as well as consolidation phenomena, which occur inside a landfill for municipal solid waste (MSW), can cause a decrease in waste permeability. This can lead to a reduction in conveyance of the leachate drainage system. It is therefore possible that a so-called perched leachate zone will form. Such a zone is constituted by an area in the body of the landfill where the leachate is temporarily trapped and is unable to infiltrate downward. This phenomenon is influenced by many factors, which include rain infiltration rate, waste moisture and composition, landfill height, and so on. The main aim of the paper is to elucidate the role played by landfill height in the formation of …
Intermittent Aeration in a Hybrid Moving Bed Biofilm Reactor for Carbon and Nutrient Biological Removal
The paper presents an experimental study on a lab scale hybrid moving bed biofilm reactor with intermittent aeration. Specifically, a comparison between two different operating conditions was analyzed: continuous and intermittent aeration. Both continuous and intermittent aeration were monitored and compared in order to get the best operational conditions. The intermittent aeration campaign was sub-divided in three phases with different duration of alternation of aerobic and anoxic times and organic and nitrogen loading rates. The efficiency of N-removal improved by 70% during the intermittent aeration. The best condition was observed with 40 min of aeration and 20 min of no-aeration, an or…
I reattori aerobici granulari: esperienze con refluo reale e sintetico
La granulazione aerobica può essere ottenuta nei sistemi con alimentazione discontinua in due differenti configurazioni impiantistiche, che permettono di realizzare i necessari sforzi tangenziali per la formazione dei granuli: il Sequencing Batch Bubble Column Reactor (SBBC) e il Sequencing Batch Airlift Reactor (SBAR). Lo scopo di questo studio è stato quello di osservare il fenomeno della granulazione aerobica e valutare il ruolo del tempo di sedimentazione durante la fase di selezione e formazione dei granuli. L’intera sperimentazione è stata suddivisa in due diverse campagne sperimentali in cui è stato utilizzato refluo sintetico, nella prima, e refluo reale, nella seconda. Al fine di e…
Cultivation of granular sludge with hypersaline oily wastewater
The time required to stabilise mature aerobic granules is rather variable. In addition, cultivation time and the structural characteristics of granules seem to be related to the nature of wastewater influent. Granular sludge has been used for the treatment of several industrial wastewaters, but nothing has been reported about wastewater characterized by the simultaneous presence of hydrocarbons and high chloride concentration. In this work, the authors analysed the granulation process and performance as well as the physical characteristics of aerobic granules in two Granular Sequencing Batch Airlift Reactors (GSBARs), fed with acetate-based synthetic wastewater in reactor 1 (R1) and with a …
Influenza dei polimeri extracellulari sul fouling e sul foaming negli impianti MBR.
L’applicazione sempre più diffusa dei bioreattori a membrana presenta tuttavia ancora alcuni fattori limitanti che ne condizionano l’adozione: infatti sono ancora incerte le previsioni della vita utile e dell’efficienza della barriera filtrante. In particolare, notevole incidenza sul processo ha il fouling, causato principalmente dai fenomeni di sporcamento condizionati prevalentemente dalla composizione della sospensione biologica sottoposta a filtrazione. Nella nota sono riportati i risultati di uno studio sperimentale che ha avuto per oggetto l’analisi dell’influenza di alcuni parametri specifici che, oltre a descrivere la qualità del fango attivo dei sistemi MBR, influenzano il processo…
An integrated model for biological and physical process simulation in membrane bioreactors (MBR).
Abstract Mathematical modelling of membrane bioreactors (MBRs) for wastewater treatment has targeted either the biological processes (treatment quality target) as well as various aspects of system management. However, the high number of interactions among the involved physical–chemical processes, hampers a straightforward mathematical modelling. This circumstance is much more emphasized for submerged MBR systems where the membrane is immersed in an aeration tank. One of the main crucial points that prevents a comprehensive understanding is the interpretation of the fouling phenomenon and its connections with the biological processes. An overall mathematical model for MBR has not been comple…
Start-up with or without inoculum? Analysis of an SMBR pilot plant.
This study analysed a submerged membrane bioreactor (SMBR) start-up with the purpose of determining the best conditions to carry it out. In order to do this, a hollow fibre membrane module was installed in a submerged configuration in a pilot aerobic reactor. The experiment was then divided in two phases, lasting 65 days each. During phase 1, the pilot plant was started-up without inoculum of activated sludge and no sludge, withdrawal was performed. Conversely, in phase 2, the MBR pilot plant was started-up with sludge inoculum and the sludge concentration was kept constant. In both phases, the volumetric loading rate applied to the pilot plant was kept constant. The authors analysed the di…
The role of EPS concentration in MBR foaming: analysis of a submerged pilot plant.
Foaming in Membrane BioReactor (MBR) is a frequently discussed topic. Some authors reported that the phenomenon is due to filamentous organisms, like at Conventional Activated Sludge (CAS) plants. However, in recent years, other authors reported that the Extra-cellular Polymer Substances (EPSs) concentration is an important factor for controlling foam as well. Nevertheless, even if a number of MBR plants are affected by foaming, presently there are no suitable methods to evaluate the phenomenon. To facilitate the study of this controversial phenomenon in an MBR system, certain foam tests proposed in the past for CASPs were investigated. The results of the tests were able to adequately measu…
The role of EPS in the foaming and fouling for a MBR operated in intermittent aeration conditions
Abstract This work investigates the causes of foaming and fouling in an Intermittent Aerated – Membrane BioReactor (IA-MBR) used for wastewater treatment. The experiment was divided into three periods with different aerated regimes expressed with different t aeration /t cycle ratio (Period I: 60 min/180 min, Period II: 80 min/180 min, Period III: 30 min/90 min). The advanced foaming tests used allow the study of the role of extracellular polymeric substances (EPSs) on foaming and fouling. In general, in the Periods I and II, good correlations between the EPSs and the Modified Scum Index without purification (MSI 0 ) and the Foam Power were observed. The results shown that the filamentous mi…
Formation Of perched leachate zones in MSW landfill
The paper presents a 1D mathematical model for the simulation of the percolation fluxes throughout a landfill for municipal solid waste (MSW). Specifically, the model is based on mass balance equations, that enable one to simulate the formation of perched leachate zones in a landfill for MSW. The model considers the landfill divided in several layers evaluating the in and out flow throughout each layer as well as the continuous moisture distribution. The infiltration flow is evaluated by means of the Darcy’s law for an unsaturated porous medium, while the moisture distribution evaluation has been carried out on the basis of the theory of the vertically distributed unsaturated flow. The solu…
Analisi della fase di start-up di un bioreattore a membrana
L’applicazione dei sistemi MBR, pur garantendo elevati rendimenti di rimozione, è ancora oggi limitata, a causa di alcuni fattori che ne condizionano il funzionamento. Tra questi, uno dei principali è il fouling dovuto ai fenomeni di sporcamento della membrana da parte della sospensione biologica. Nella memoria si riportano i primi risultati di uno studio che ha avuto l’obiettivo di definire l’evoluzione e l’influenza del fouling sul processo di filtrazione durante la fase di avviamento dell’impianto, avvenuto senza inoculo iniziale di fango. La sperimentazione è stata condotta in un impianto pilota costituito da un bioreattore all’interno del quale è stato installato il modulo di membrane …
Comparison between moving bed-membrane bioreactor (MB-MBR) and membrane bioreactor (MBR) systems: Influence of wastewater salinity variation
Two pilot plant systems were investigated for the treatment of wastewater subject to a gradual increase of salinity. In particular, a membrane bioreactor (MBR) and a moving bed biofilm membrane bioreactor (MB-MBR) were analyzed. Carbon and ammonium removal, kinetic constants and membranes fouling rates have been assessed. Both plants showed very high efficiency in terms of carbon and ammonium removal and the gradual salinity increase led to a good acclimation of the biomass, as confirmed by the respirometric tests. Significant biofilm detachments from carriers were experienced, which contributed to increase the irreversible superficial cake deposition. However, this aspect prevented the por…
Performance of membrane bioreactor (MBR) systems for the treatment of shipboard slops: Assessment of hydrocarbon biodegradation and biomass activity under salinity variation
In order to prevent hydrocarbon discharge at sea from ships, the International Maritime Organization (IMO) enacted the MARPOL 73/78 convention in which any oil and oil residue discharged in wastewater streams must contain less than 5. ppm hydrocarbons. Effective treatment of this petroleum-contaminated water is essential prior to its release into the environment, in order to prevent pollution problem for marine ecosystems as well as for human health. Therefore, two bench scale membrane bioreactors (MBRs) were investigated for hydrocarbon biodegradation. The two plants were initially fed with synthetic wastewater characterised by an increasing salinity, in order to enhance biomass acclimatio…
Evaluation of biomass activity and wastewater characterization in a UCT-MBR pilot plant by means of respirometric techniques
Abstract Over the last two decades, Membrane Bioreactors (MBRs) emerged even more for wastewater treatment, ensuring high removal efficiencies as well as very small footprint requirements. Indeed, in this kind of process, a modification in biomass activity and viability can exist compared to that of a CAS process. In this context, respirometric analysis represents a reliable tool in order to evaluate the actual biomass kinetic parameters, to insert in mathematical models in the design phase, as well as to monitor the biomass viability, especially when these processes are operated with high SRT values. The paper presents some results of respirometric techniques applied for the characterisati…