0000000000211408
AUTHOR
D. Scire
showing 13 related works from this author
Custom measurement system for memristor characterisation
2021
Abstract A cheap, compact and customisable characterisation system for memristor devices, working between ± 10 V, is presented. SPICE (Simulation Program with Integrated Circuit Emphasis) simulations are performed to verify the circuit feasibility and a proper software is developed to drive the system. The potentiality of the realised system is tested by performing several electrical measurements on both Cu/HfO2/Pt memristors and two-terminals commercial devices.
Non-linear inductor modelling for a DC/DC buck converter
2017
The paper is focused on the modelling of an inductor to exploit its non-linear behaviour in the roll-off region when it is employed in a DC/DC converter. The model is set up on the basis of experimental data measured in operating conditions, which are fitted to a polynomial curve describing the inductance variations. The analysis of the buck converter, performed by including the proposed model, is validated by experimental tests.
Characterization of Non-linear Inductors Including Thermal Effects for Power Applications
2018
This paper is focused on the behaviour of non-linear inductors employed in DC/DC switching converters considering the effects due to variations of both current and temperature. The characterization of the inductors is performed by a buck converter operated to stimulate the inductor under test by a constant current with superimposed a large signal. The measurements are carried out at several inductor’s temperature values. Data are automatically collected by a novel virtual instrument developed by the authors in LabVIEW® environment aiming to obtain a polynomial based analytical model. The deep knowledge of the inductor model allows its design to be optimized improving the power density of th…
Design and Modeling of an Interleaving Boost Converter with Quasi-Saturated Inductors for Electric Vehicles
2020
This paper is focused on the analysis and modeling of DC-DC boost converters in interleaving configuration exploiting inductors in the quasi-saturation region. The converter is designed to optimize the power density by minimizing the size of the inductors. A simulation study for electric vehicle applications is conducted analyzing the effects of duty cycle and temperature variation on the ripple of the input current giving, moreover, information on the performances and dynamics of the converter for further implementation and optimizations.
Characterization of the defect density states in MoOx for c-Si solar cell applications
2021
Thin layers of MoOx have been deposited by thermal evaporation followed by post-deposition annealing. The density of states distributions of the MoOx films were extracted deconvoluting the absorption spectra, measured by a photothermal deflection spectroscopy setup, including the small polaron contribution. Results revealed a sub-band defect distribution centered 1.1 eV below the conduction band; the amplitude of this distribution was found to increase with post-deposition annealing temperature and film thickness.
Analysis of Transition Metal Oxides based Heterojunction Solar Cells with S-shaped J-V curves
2020
The use of transition metal oxides for the selective carrier contact in the crystalline silicon solar cells technology is rising to interest for the excellent optoelectrical properties of these materials whose implementation, however, can result in lousy performing cells due to an S-shaped electrical characteristic. In this paper, we fabricated solar cells showing S-shaped J-V curve and carried out an analysis of the reasons of such behavior using a model involving the series of a standard cell equivalent circuit with a Schottky junction in order to explain these atypical performances. A good matching between the experimental measurements and the adopted theoretical model was obtained. The …
Progress in Violet Light-Emitting Diodes Based on ZnO/GaN Heterojunction
2020
Progress in light-emitting diodes (LEDs) based on ZnO/GaN heterojunctions has run into several obstacles during the last twenty years. While both the energy bandgap and lattice parameter of the two semiconductors are favorable to the development of such devices, other features related to the electrical and structural properties of the GaN layer prevent an efficient radiative recombination. This work illustrates some advances made on ZnO/GaN-based LEDs, by using high-thickness GaN layers for the p-region of the device and an ad hoc device topology. Heterojunction LEDs consist of a quasicoalesced non-intentionally doped ZnO nanorod layer deposited by chemical bath deposition onto a metal&ndash
A Temperature Dependent Non-Linear Inductor Model for a DC/DC Boost Converter
2018
This paper is focused on the use of non-linear inductors in DC/DC switching converters, as well as their behaviour due to changes in current and temperature. The model of an inductor is set up on the basis of experimental data, which are automatically acquired by a virtual instrument; from those data, a polynomial curve describing the inductance variations is obtained. The analysis of the converter, performed by including the proposed model, is validated by experimental tests.
EMI Filter Re-Design in a SMPS with Inductor in Saturation
2021
This paper analyzes the design issues of the input EMI (Electro-Magnetic Interference) filter's in a switching mode power supply where the power inductor is operated in saturation. Starting with a SMPS equipped with linear inductor, the input filter is firstly designed to comply with Standards. Then, a new inductor with a smaller core size is employed in the same SMPS to exploit saturation. The EMI filter is re-designed, taking into account the increase of EMI introduced by the non-linear operation of the inductor. Finally, the reduction of the inductor's size and cost is compared with the increased size and cost of the EMI filter.
Thermal Stability of a DC/DC Converter with Inductor in Partial Saturation
2021
Inductors operated in quasi saturation in dc–dc converters allow reduction of the core size and realization costs; on the other hand, they imply an increase of dissipated power that can jeopardize the thermal stability of the converter. In this article, this issue is studied by a mathematical model able to represent both the inductor nonlinearity and its temperature dependence. The main losses, such as ohmic, skin effect and magnetic, are taken into account in the model. The inductor is characterized by a polynomial curve whose parameters are a function of the temperature. Finally, the whole converter is modeled and simulation results, obtained on a boost converter, are compared with experi…
Equivalent Circuit Modelling of Ferrite Inductors Losses
2018
The modelling of the magnetic losses in the core of ferrite inductors for power conversion circuits has been considered in this paper. On the basis of the Revised Generalized Steinmetz Model (RGSE) an equivalent circuital modelling has been obtained. The losses are modelled as an equivalent resistance connected in parallel to the inductor. The model has been tested under periodic triangular current waveforms.
A Measurement System for Power Inductors in Non-Linear Operating Conditions
2021
The exploitation of power inductors in switching converters outside the linear region requires detailed information on the magnetization curve that often is not included among those usually available on their datasheets. This paper proposes an automatic system in which the inductor is characterized in real operating conditions taking into account also the core temperature. It is based on a switching converter suitably controlled by a virtual instrument. The system was tested by retrieving the inductance vs current curves of two commercial inductors for core temperatures up to 105°C, showing the different behaviors of the magnetization curves. Results are coherent with data given by manufact…
Sub-gap defect density characterization of molybdenum oxide: An annealing study for solar cell applications
2020
AbstractThe application of molybdenum oxide in the photovoltaic field is gaining traction as this material can be deployed in doping-free heterojunction solar cells in the role of hole selective contact. For modeling-based optimization of such contact, knowledge of the molybdenum oxide defect density of states (DOS) is crucial. In this paper, we report a method to extract the defect density through nondestructive optical measures, including the contribution given by small polaron optical transitions. The presence of defects related to oxygen-vacancy and of polaron is supported by the results of our opto-electrical characterizations along with the evaluation of previous observations. As part…