Spectrometric analysis of inner divertor materials of JET carbon and ITER-like walls

2019

Abstract One of main reasons of the Joint European torus (JET) transformation from the carbon (JET-C) to ITER-like (JET-ILW) wall was high tritium retention of carbon. In order to compare the tritium retention, samples of analogous positions of the plasma-facing side of vertical tiles No. 3 of two campaigns: JET-C (2008–2009) and JET-ILW (2011–2012) were cut out. Temperature-programmed tritium desorption spectrometry in He + 0.1% H2 gas flow showed that JET-C sample without a tungsten coating had by a factor of >20 higher surface concentration of tritium than JET-ILW tungsten-coated sample: 4.9 × 1013 and 1.7–2.2 × 1012 T atoms/cm2 respectively. Installation of metallic plasma facing wall i…

Interface of Silicon Nitride Nanolayers with Oxygen Deficiency

2018

Multilayer Si 3 N 4 consisting of Si 3 N 4 nanolayers with the total thickness 60 nm was deposited layer-by-layer in a low-pressure chemical vapor deposition process. Compared with the single-layer Si 3 N 4 , the multilayer Si 3 N 4 had one-third less oxygen concentration at the interfaces. This decreased density of electrically active centers of oxygen traps and improved quality of nanocapacitors with multilayer Si 3 N 4 dielectric.

Spatially resolved nanostructural transformation in graphite under femtosecond laser irradiation

2015

Abstract A polycrystalline graphite target was irradiated using infrared (800 nm) femtosecond (120 fs) laser pulses of different energies. Increase of sp 3 bonds percentage and possible diamond crystal formation were investigated ‘in-depth’ and on the irradiated surfaces. Synchrotron X-ray diffraction pattern have shown the presence of a diamond peak in one of the irradiated zones while X-ray photoelectron spectroscopy investigations have shown an increasing tendency of the sp 3 percent in the low power irradiated areas and similarly ‘in the depth’ of the higher power irradiated zones. Multiple wavelength Micro-Raman investigations have confirmed this trend along with an ‘in-depth’ (but not…

Radiation resistance of nanolayered silicon nitride capacitors

2020

Abstract Single-layered and multi-layered 20–60 nm thick silicon nitride (Si3N4) dielectric nanofilms were fabricated using a low-pressure chemical vapour deposition (LPCVD) method. The X-ray photoelectron spectroscopy (XPS) confirmed less oxygen content in the multi-layered nanofilms. The capacitors with Si3N4 multilayer demonstrated a tendency to a higher breakdown voltage compared to the capacitors with Si3N4 single layer. Si3N4 nanofilms and capacitors with Si3N4 dielectric were exposed to 1 kGy dose of gamma photons. Fourier transform infrared (FTIR) spectroscopy analysis showed that no modifications of the chemical bonds of Si3N4 were present after irradiation. Also, gamma irradiation…

Tritium in plasma-facing components of JET with the ITER-Like-Wall

2021

FTIR Analysis of Electron Irradiated Single and Multilayer Si<sub>3</sub>N<sub>4</sub> Coatings

2018

Silicon nitride (Si3N4) due to its good mechanical and electrical properties is a promising material for wide range of applications, including exploitation under action of ionizing radiation. For estimating the changes of chemical bonds in silicon nitride nanolayers under action of ionizing radiation single and multi-layer silicon nitride nanolayered coatings on prepared Si subtrate were investigated by means of Fourier transform infrared spectrometry. Three main groups of signals were identified in both types of nanolayers, at 510 and 820 cm-1 and group of broad signals at 1000-1200 cm-1. Irradiation with accelerated electrons up to absorbed doses 36 MGy causes minor changes of signal inte…

Laser irradiation of carbon–tungsten materials

2014

Carbon–tungsten layers deposited on graphite by thermionic vacuum arc (TVA) were directly irradiated with a femtosecond terawatt laser. The morphological and structural changes produced in the irradiated area by different numbers of pulses were systematically explored, both along the spots and in their depths. Although micro-Raman and Synchrotron-x-ray diffraction investigations have shown no carbide formation, they have shown the unexpected presence of embedded nano-diamonds in the areas irradiated with high fluencies. Scanning electron microscopy images show a cumulative effect of the laser pulses on the morphology through the ablation process. The micro-Raman spatial mapping signalled an…

Tritium retention in plasma facing materials of JET ITER-Like-Wall retrieved from the vacuum vessel in 2012 (ILW1), 2014 (ILW2) and 2016 (ILW3)

2021

Abstract ITER-Like-Wall (ILW) project has been carried out at Joint European Torus (JET) to test plasma facing materials relevant to International Thermonuclear Experimental Reactor – ITER [1]. Limiters and an upper dump plate of the vacuum vessel are made of bulk beryllium tiles, whereas for the divertor bulk tungsten and tungsten-coated carbon fibre (CFC) composite tiles are used. During the shutdowns in ILW1 (2012), ILW2 (2014) and ILW3 (2016), selected beryllium tiles were removed from the vacuum vessel. In this study, tiles from three positions were analysed, and analysis results were compared regarding both the tile position in the vacuum vessel and differences in the exploitation con…

Comparison of tritium measurement techniques for a laser cleaned JET tile

2014

Abstract Over the last 7–8 years, two quantitative analyzing methods—accelerator mass spectrometry (AMS) and full combustion (FC) followed by scintillation detection have been applied for determining the tritium activity concentrations in JET divertor tiles. These methods have two main differences – the range of detection and the spatial resolution – and are thus complementary. However, these differences can also complicate the comparison of the two techniques for typical JET divertor samples. Therefore a cross comparison exercise for tritium measurements was performed between the two methods using specially produced identical standard samples. The cross comparison measurements were perform…

Overview of the JET results in support to ITER

2017

The 2014–2016 JET results are reviewed in the light of their significance for optimising the ITER research plan for the active and non-active operation. More than 60 h of plasma operation with ITER first wall materials successfully took place since its installation in 2011. New multi-machine scaling of the type I-ELM divertor energy flux density to ITER is supported by first principle modelling. ITER relevant disruption experiments and first principle modelling are reported with a set of three disruption mitigation valves mimicking the ITER setup. Insights of the L–H power threshold in Deuterium and Hydrogen are given, stressing the importance of the magnetic configurations and the recent m…

Growth of beryllium oxide nano-structures during thermal treatment of neutron irradiated beryllium

2015

Beryllium oxide nano-structures grown during high temperature oxidation of neutron irradiated beryllium has been investigated. Oxidation of non - irradiated and neutron irradiated beryllium was performed in differential thermal analyzer in an atmosphere of air and its mixture with helium at temperatures up to 1050°C. Structure of beryllium and its oxide was studied by the means of scanning electron microscopy. The growth of beryllium oxide nano-structures – “labyrinth type” layers and nano-rods on the inner surfaces of neutron irradiated beryllium were observed by means of Scanning Electron Microscopy. The size of the rods was 10-100 nm in diameter and up to few micrometers in length. There…

TG/DTA-FTIR as a method for analysis of tall oil based rigid polyurethane foam decomposition gaseous products in a low oxygen environment

2020

Abstract This study is an investigation of the suitability of the thermogravimetry and differential thermal analysis method coupled with Fourier Transform Infrared spectrometry (TG/DTA-FTIR) for a thermal degradation gaseous product analysis of a rigid polyurethane-polyisocyanurate (PU-PIR) foam synthesised from high functionality tall oil fatty acids (TOFA) based polyols. The FTIR spectra of the TG-generated gaseous thermal degradation products of three PU-PIR formulations with varied high functionality TO based polyol content (45, 75 and 95 pbw) and a different tier of isocyanate (NCO) indexes (110, 150, 200, 300 and 400) for each formulation were compared to the spectra of a formulation …

Fuel inventory and material migration of JET main chamber plasma facing components compared over three operational periods

2020

Fuel retention and material migration results from JET ITER-like wall beryllium limiter tiles are presented for three operating periods. Ion beam analysis results support the general picture of erosion during limiter configurations with local deposition on tile ends far into the scrape off layer. Similar trends of fuel concentrations are observed in all JET operating periods; (i) low on surfaces exposed to high heat flux and erosion and (ii) higher in deposits. The pattern of fuel retention and deposition correlates with heat flux and distribution of limiter plasmas touching inner and outer limiters. The D/Be ratio in the thickest deposit is similar to 0.01. Global fuel retention attributed…

Surface Morphology of Single and Multi-Layer Silicon Nitride Dielectric Nano-Coatings on Silicon Dioxide and Polycrystalline Silicon

2019

Silicon nitride (Si3N4) in a form of single and multi-layer nanofilms is proposed to be used as a dielectric layer in nanocapacitors for operation in harsh environmental conditions. Characterization of surface morphology, roughness and chemical bonds of the Si3N4 coatings has an important role in production process as the surface morphology affects the contact surface with other components of the produced device. Si3N4 was synthesized by using low pressure chemical vapour deposition method and depositing single and multi-layer (3 – 5 layers) nanofilms on SiO2 and polycrystalline silicon (PolySi). The total thickness of the synthesized nanofilms was 20 – 60 nm. Surface morphology was investi…

Influence of Biomass Combustion Products on Element Content and Thermal Stability of Latvian Sheep Breed Wool Filter Fibres

2020

Sheep wool is natural, easy obtainable, renewable and biodegradable material with a perspective application as a sorbent in filters for purification of industrial emissions from various environmental pollutants. The element content and thermal stability of Latvian dark-headed sheep wool filter fibres was analysed and described before and after exposure to biomass combustion products. Based on the obtained results, it is concluded that the sheep wool filter fibres can sorb various gaseous combustion products, such as carbon monoxide (CO), carbon dioxide (CO2) and nitrogen oxides (NOx), however, the sorption processes of these gases are irreversible. The obtained results of total reflection X…

Efficient generation of energetic ions in multi-ion plasmas by radio-frequency heating

2017

We describe a new technique for the efficient generation of high-energy ions with electromagnetic ion cyclotron waves in multi-ion plasmas. The discussed ‘three-ion’ scenarios are especially suited for strong wave absorption by a very low number of resonant ions. To observe this effect, the plasma composition has to be properly adjusted, as prescribed by theory. We demonstrate the potential of the method on the world-largest plasma magnetic confinement device, JET (Joint European Torus, Culham, UK), and the high-magnetic-field tokamak Alcator C-Mod (Cambridge, USA). The obtained results demonstrate efficient acceleration of 3He ions to high energies in dedicated hydrogen–deuterium mixtures.…

Novel method for determination of tritium depth profiles in metallic samples

2019

Tritium accumulation in fusion reactor materials is considered a serious radiological issue, therefore a lot of effort has been concentrated on the development of radiometric techniques. A novel method, based on gradual dissolution, for the determination of the total tritium content and its depth profiles in metallic samples is demonstrated. This method allows for the measurement of tritium in metallic samples after their exposure to a hydrogen and tritium mixture, tritium containing plasma or after irradiation with neutrons resulting in tritium formation. In this method, successive layers of metal are removed using an appropriate etching agent in the controlled regime and the amount of evo…

Overview of the JET results

2015

Since the installation of an ITER-like wall, the JET programme has focused on the consolidation of ITER design choices and the preparation for ITER operation, with a specific emphasis given to the bulk tungsten melt experiment, which has been crucial for the final decision on the material choice for the day-one tungsten divertor in ITER. Integrated scenarios have been progressed with the re-establishment of long-pulse, high-confinement H-modes by optimizing the magnetic configuration and the use of ICRH to avoid tungsten impurity accumulation. Stationary discharges with detached divertor conditions and small edge localized modes have been demonstrated by nitrogen seeding. The differences in…

Comparison of the structure of the plasma-facing surface and tritium accumulation in beryllium tiles from JET ILW campaigns 2011-2012 and 2013-2014

2019

In this study, beryllium tiles from Joint European Torus (JET) vacuum vessel wall were analysed and compared regarding their position in the vacuum vessel and differences in the exploitation conditions during two campaigns of ITER-Like-Wall (ILW) in 2011-2012 (ILW1) and 2013-2014 (ILW2) Tritium content in beryllium samples were assessed. Two methods were used to measure tritium content in the samples - dissolution under controlled conditions and tritium thermal desorption. Prior to desorption and dissolution experiments, scanning electron microscopy and energy dispersive x-ray spectroscopy were used to study structure and chemical composition of plasma-facing-surfaces of the beryllium sampl…

Overview of the JET results with the ITER-like wall

2013

Following the completion in May 2011 of the shutdown for the installation of the beryllium wall and the tungsten divertor, the first set of JET campaigns have addressed the investigation of the retention properties and the development of operational scenarios with the new plasma-facing materials. The large reduction in the carbon content (more than a factor ten) led to a much lower Zeff (1.2-1.4) during L- and H-mode plasmas, and radiation during the burn-through phase of the plasma initiation with the consequence that breakdown failures are almost absent. Gas balance experiments have shown that the fuel retention rate with the new wall is substantially reduced with respect to the C wall. T…

Modelling of JET hybrid plasmas with emphasis on performance of combined ICRF and NBI heating

2018

International audience; During the 2015--2016 JET campaigns, many efforts have been devoted to the exploration of high-performance plasma scenarios envisaged for DT operation in JET. In this paper, we review various key recent hybrid discharges and model the combined ICRF NBI heating. These deuterium discharges with deuterium beams had the ICRF antenna frequency tuned to match the cyclotron frequency of minority H at the centre of the tokamak coinciding with the second harmonic cyclotron resonance of D. The modelling takes into account the synergy between ICRF and NBI heating through the second harmonic cyclotron resonance of D beam ions, allowing us to assess its impact on the neutron rate…