An inertial system for the production of electricity and hydrogen from sea wave energy

2015

This paper aims at describing a small scale prototype of a complete wave energy converter system for hydrogen production promoting the opportunity of installation in Sicily, in the Mediterranean Sea. The opportunity to produce hydrogen from sea-water identifies ocean wave energy as the most promising solution for electricity generation including hydrogen production and storage. Even if hydrogen is considered one of the most promising secondary sources, criticism arises from both the academic and the industrial world mainly because hydrogen production requires electricity consumption. Furthermore, safety problems concerning hydrogen storage and transport are actually the main hindrance to fu…

An Experimental Comparison between an Ironless and a Traditional Permanent Magnet Linear Generator for Wave Energy Conversion

2022

Permanent Magnet Linear Generators (PMLGs) are currently being studied for sea wave energy harvesting. Typically, a PMLG consists of an iron-made armature and a moving translator. The permanent magnets adoption produces parasitic effects, such as cogging force, and the machine weight increment. A solution could be the adoption of an ironless configuration, accepting a power density reduction. This paper investigates the use of ironless PMLGs in sea wave energy conversion systems by an experimental comparative analysis between an iron PMLG prototype and an ironless PMLG prototype, which share the same geometry. The main electrical and mechanical parameters (resistance, mass, and magnetic fie…

Assessment of the Operating Temperature of Crystalline PV Modules Based on Real Use Conditions

2014

Determining the operating temperatureTcof photovoltaic panelsPVis important in evaluating the actual performance of these systems. In the literature, different correlations exist, in either explicit or implicit forms, which often do not account for the electrical behaviour of panels; in this way, estimatingTcis based only on the passive behaviour of thePV. In this paper, the authors propose a new implicit correlation that takes into account the standard weather variables and the electricity production regimes of aPVpanel in terms of the proximity to the maximum power points. To validate its reliability, the new correlation was tested on two different PV panels (Sanyo and Kyocera panels) and…

Design and Performance of a High Temperature Superconducting Axial Flux Generator

2013

In this paper, a high temperature axial flux (HTSAF) generator is presented. In this generator the excitation of the generator is obtained by using some high temperature superconducting magnets. In order to reduce the negative effects of vibrations, the excitation is located on the stationary part of the generator. Starting, running and endurance tests of the machine are presented.

First proposal of a methodology for a preventive assessment of the acoustic impact of advanced landfills

2005

In this paper, the results of a preliminary study on the environmental noise pollution of a technologically advanced landfill to be realized in Sicily (Italy) are presented. The investigation has been carried out analysing, at the beginning, a simulating model suggested by the European Community. The method makes reference to the ISO 9613-2:1996 standard, which suggests a general method of calculation to assess the attenuation of sound during propagation outdoors. The simulation has pointed out the troubles in carrying out the noise pollution assessment of an advanced landfill, where several and different kinds of sound sources are present at the same time; it isn’t always possible, for exa…

Environmental Impact Assessment (EIA) of Wave Energy Converter (WEC)

2015

The Environmental Impact Assessment (EIA) is an environmental management instrument implemented worldwide. In the last years the development of Wave Energy Converter (WEC) influenced environmental research to quantify impacts on marine life. In this paper we present a case study of EIA: a real application and study of device installed in Tirren Sea (near Castellammare — Sicily).

Dynamic Preisach Hysteresis Model for Magnetostrictive Materials for Energy Application

2013

In this paper the magnetostrictive material considered is Terfenol-D. Its hysteresis is modeled by applying the DPM whose identification procedure is performed by using a neural network procedure previously publised [. The neural network used is a multiplayer perceptron trained with the Levenberg-Marquadt training algorithm. This allows to obtain the Preisach distribution function, without any special conditioning of the measured data, owing to the filtering capabilities of the neural network interpolators. The model is able to reconstruct both the magnetization relation and the Field-strain relation. The model is validated through comparison and prediction of data collected from a typical …

A Review of the Water Desalination Technologies

2021

Desalination is commonly adopted nowadays to overcome the freshwater scarcity in some areas of the world if brackish water or salt water is available. Different kinds of technologies have been proposed in the last century. In this paper, the state of the mainstream solutions is reported, showing the current commercial technologies like reverse osmosis (RO), Multi-Stages Flash desalination (MSF) and Multi-Effect Distillation (MED), and the new frontiers of the research with the aim of exploiting renewable sources such as wind, solar and biomass energy. In these cases, seawater treatment plants are the same as traditional ones, with the only difference being that they use a renewable energy s…

Investigation on a Bio-Composite Material as Acoustic Absorber and Thermal Insulation

2020

In order to limit the anthropic emissions of CO2, research is currently investigating new materials for the building sector. The main purpose is the reduction in the embodied energy consumption, especially in the residential sector, and consequently the limitation of the direct and indirect utilization of fossil fuels, for the indoor heating, cooling, and ventilation services. Indeed, the residential sector is affected by a high energy demand, thus the choice of improved materials is fundamental to improve the sustainability. All phases: construction, building life, and dismantling are impacting in terms of resource and energy consumption, both associated with the emissions of pollutants in…

Testing a linear ironless generator for the sea wave energy harvesting

2022

Wave energy represents a "new entry"in the renewable energy sector; however, it is believed that in near future sea wave might have a key role for the electrical energy production, thanks its huge energy potential. In this context, the paper suggests an innovative ironless linear generator, that can be used as main component inside a point absorber. In order to exploit the wave energy potential in the Mediterranean Sea, the Engineering Department of Palermo University realized a first small-scale prototype of the electrical linear generator, that is the main component for the energy conversion.

Optimization of Wave Energy Converter: DEIM Point Absorber II

2018

The paper presents a possible solution to optimize a wave energy converter, device able to exploit the wave energy resource. The utilization of this technology shows also positive aspects, thanks to the limited visual and environmental impacts. This system could be also installed in reserved areas, being similar to signal buoys, simplifying the problem of energy supply in small islands. In order to exploit the wave energy potential in the Mediterranean Sea, the department of Energy of Palermo University realized a first prototype of the electrical linear generator, that is the main component of the wave energy converter. This electrical machine can be operated by a two-floating buoys system…

Minimization of detent force in a 1 kW linear permanent magnet generator for the conversion of sea waves energy: Numerical and experimental validation

2015

Linear permanent magnet generators are widely considered for the direct conversion of energy contained in sea waves [1-3]. Both planar and tubular structures have been proposed [4-6] and all these structures present several advantages: relative high efficiency, simplicity of the structures, high sturdiness. However, as all other linear machines they present some drawbacks: oscillations in the movement, distortion in the generated electromotive force (emf), etc. In this paper we focus our attention on the parasitic oscillations of the translator which are caused by the presence of a high detent force. Detent force is generated by the fact that magnetic energy presents a minimum when the leng…

A New Solution for Sea Wave Energy Harvesting, the Proposal of an Ironless Linear Generator

2020

The paper investigates an innovative ironless linear generator, installable inside a wave energy converter, in order to produce electricity from sea waves. This energy source is considered strategic for the future, especially in small islands

Toward a European Eco-label brand for residential buildings: Holistic or by-components approaches?

2011

The Eco-label scheme is becoming ever more important in the environmental certification of products and services, especially in light of the recent ambitious aim of containing greenhouse emissions and improving the efficiency of utilizing energy sources. A recently-introduced hypothesis concerns the European Eco-label scheme relating to buildings, in the awareness that the construction industry is of primary importance to the whole economic and social life of states. This scheme should adopt an integrated approach to environmental problems and include construction, day-to-day management, and the possible disposal of building materials, throughout the life cycle of the building. In addition,…

Seawave Power Farm Design:A Case Study

2012

Currentenergycrisisandgeneralconcernsonenvvironmentalissueshavetriggeredaneverincreasingeffortoonharvestingrenewableenergies.Amongstrenewableenergysources,seawaveene ergyisdefinitelytheonethathasbeenlessutilised.Thisisprobablycausedbytworeasons:i)thes strongtechnicalnoveltiesthatarerequiredtoextractthee energythatiscontainedinahighlyandstochasticallyvariablem motion;ii)thedifficultyofindasuitableelectricalsystemabbletoconverttheenergycontainedinthemotionoftheseaintoelectricalenergy.Inthispaperweproposeanapproachtosetupaggeneralmethodologytowardthedesignofaseawavefarm.Thefirststepisexplainedhowtochoosetheconversionsysteem,inthesecondstepisdiscussedtheconnectionschem meamongtheconverters,inth…

A Finite Difference Model of a PV-PCM System

2012

Abstract The performances of a photovoltaic panel (PV) are defined according to the “peak power” that identifies the maximum electric power supplied by the panel when it receives an insolation of 1 kW/m2 and the temperature of the cell is maintained at 25 °C. These conditions are only nominal since the solar radiation has a variable intensity and also the panel is subjected to thermal excursions; due to these reasons the real power efficiency of the panel is considerably lower than that obtainable in the nominal conditions. The study focused on assessing a method to reduce the peak temperatures of PV systems using Phase Change Materials (PCM). To this aim it was created a numerical model ca…

Renewable Energy Assessment in Italy and Brazil: An Economic and Political Comparison

2017

The aim of this study is a comparison among Italian and Brazilian electrical energy system with a particular focus on renewable energy sources. The energy sector has a key role in the sustainable development of a country, so it influences economic and political choices. The work would underline differences, common point among two country, specially, in this particular socio-economic period and it should emphasize that green economy could be a possible answer to financial crisis. The main purpose of this study is a presentation of Italian and Brazilian energy system with a particular focus on renewable sources. The energy sector has a key role in the sustainable development of these countrie…

Greening island: Renewable energies mix to satisfy electrical needs of Pantelleria in Mediterranean sea

2016

In this article the authors analyze the renewable mix in order to satisfy the energy needs of a real island in the Mediterranean sea, Pantelleria, which represents an optimal starting point to increase the production of electrical energy from renewable sources in minor islands. In this text are exposed different alternative sources, such as solar, wind and wave energy. Moreover, it is exposed a project of an innovative conversion device proposed by Department of Energy of University of Palermo, compared to a different one proposed by Politecnico di Torino. The procedures applied in the present article, as well as the main equations used, are the result of previous applications made in diffe…

A dynamic model for hysteresis in magnetostrictive devices

2014

In this paper, a dynamic model for the description and design of hysteresis in magnetostrictive devices is presented. The model is based on Preisach theory and its dynamic extension. A procedure for determining the Preisach distribution function is given. This procedure is based on neural networks. The model is able to reconstruct both the magnetization relation and the field-strain relation. The model is validated through comparison and prediction of data collected from a typical Terfenol-D sample and a novel experimental technique dedicated to the validation of dynamic models is proposed.

The use of hydrogen in residential building climatisation: Technical and economic valuations

2005

Wave and Wind Energy Systems Integration in Vietnam: Analysis of Energy Potential and Economic Feasibility

2020

Vietnam energy demand is currently growing at a very high annual rate, with the government being very interested in investments in renewable energies. Since the region with the highest solar and wind potential is far away from the big load centers, an investigation of offshore energy resources is here proposed. In this study, a review of previous energy potential assessments is provided. Moreover, the minimum feed-in-tariff to make the investments profitable is evaluated, showing that the current tariff for offshore wind plants is largely unattractive.

Energy, economic and environmental analysis on RET-hydrogen systems in residential buildings

2008

The aim of this study was to analyze energy, economic and environmental performances of a set of scenarios dealing with the production and the use of hydrogen as energy carriers in residential applications in combination with renewable energy (RE). The authors also made an investigation into the required economic conditions necessary for making H2–RE residential systems competitive with conventional ones, which are based on the use of grid electricity and natural gas. A case study was enacted in a small residential district in Palermo (Italy) made by five multi-storey buildings. Many energy systems have been considered according to several fuel-device combinations (electric grid, fuel cell,…

The effect of manufacturing tolerances on a tubular linear ferrite motor

2015

This study presents a numerical and experimental study on the effect of permanent magnet tolerances on the performances of a Tubular Linear Ferrite Motor. The statistical distribution of the magnetic characteristic of a set of commercial magnets is obtained experimentally while the performances of a the tubular motor are numerically evaluated. The performances that have been considered are: cogging force, end effect force and generated thrust. It has been shown that: 1)the statistical variability of the magnets modifies the time behavior of the cogging force; 2)the value of both the end effect cogging force and the generated thrust are directly linked to the values of then remanence field o…

Design of Bilateral Switched Reluctance Linear Generator to Convert Wave Energy: Case Study in Sicily

2013

The aim of this work is a case study of the adaptation bilateral switched reluctance linear generator to the exploitation of energy of the sea. This type of generator can be used to convert wave energy in electrical energy. In this paper we present an analytical sizing and FEM simulation. As for the results, analysis of the data extracted through the simulations it was possible to calculate the emf. The emf was calculated in two cases of motion of the slider: first hypothesis has set the constant speed while the second is a variable speed according to the law of an oscillatory motion of the sea.

Primary Data Collection and Environmental/Energy Audit of Hot Mix Asphalt Production

2020

The development of the road construction sector determines the consequences on consumption of non-renewable resources, energy expenditure and environmental pollution. Recent sustainability issues have highlighted the importance of efficient design and quality-oriented techniques in this sector, due to the huge amount of materials involved in construction and maintenance activities. Thus, it is necessary to properly quantify the environmental impacts of asphalt mixtures used for pavement construction, considering the whole life cycle of the products. Life cycle assessment (LCA) represents the most appropriate methodological framework for assessing the environmental burdens of a product, from…

An electromagnetic generator for MAGLEV transportation systems

2015

The fundamental idea of this paper is to use the distribution theory to analyze linear generators in order to include in the mathematical model both ideal a non ideal features. This paper shows how the use of distribution theory can be used in order to establish a mathematical model able to describe both the ordinary working condition of a linear generator for MAGLEV systems as well the role of the unavoidable irregularities and non-ideal features.

Assessment of the Usability and Accuracy of Two-Diode Models for Photovoltaic Modules

2017

Many diode-based equivalent circuits for simulating the electrical behaviour of photovoltaic (PV) cells and panels are reported in the scientific literature. Two-diode equivalent circuits, which require more complex procedures to calculate the seven model parameters, are less numerous. The model parameters are generally calculated using the data extracted from the datasheets issued by the PV panel manufactures and adopting simplifying hypotheses and numerical solving techniques. A criterion for rating both the usability and accuracy of two-diode models is proposed in this paper with the aim of supporting researchers and designers, working in the area of PV systems, to select and use a model…

Update on desiccant wheel model

2004

This short communication presents the update on the desiccant wheel models, developed earlier by the present authors. It is to be mentioned here that the psycrometric model presented earlier (Int. J. Energy Res., 2003; 27:17) is valid only for the desiccant wheel running with identical volume air-flows in supply and regeneration sides. However, when system runs with volume air flow ratio between supply and regeneration side (α), different from 1 (one), the model need further modifications. In the present work, correction factors were developed and incorporated in order to update the earlier model for predicting correctly the temperature and humidity of processed air at the outlet of desicca…

Assessment of the Trend of Albedo: a Case Study of Palermo

2013

In this paper we propose a case study of urban heat island applied to Palermo. The urban heat island (UHI) is the most studied of the climate effects of settlements. The UHI refers to the generally warm urban temperatures compared to those over surrounding, non-urban, areas. The aim of this paper is to find a connection among the average rise in temperature and the modification of albedo.

Experimental Test and Simulations on a Linear Generator-Based Prototype of a Wave Energy Conversion System Designed with a Reliability-Oriented Appro…

2017

In this paper, we propose a reliability-oriented design of a linear generator-based prototype of a wave energy conversion (WEC), useful for the production of hydrogen in a sheltered water area like Mediterranean Sea. The hydrogen production has been confirmed by a lot of experimental testing and simulations. The system design is aimed to enhance the robustness and reliability and is based on an analysis of the main WEC failures reported in literature. The results of this analysis led to some improvements that are applied to a WEC system prototype for hydrogen production and storage. The proposed WEC system includes the electrical linear generator, the power conversion system, and a sea-wate…

A study about the acoustical impact in high traffic urban streets

2003

EXTERNAL RECIRCULATION IN PRS TYPE TURBINE: EXPERIMENTAL AND NUMERICAL RESULTS.

2022

Cavitation is a relevant phenomenon for structural safety and noise level in hydraulic turbines, occurring when water pressure falls below the vapor value at a given temperature. In this case bubbles of vapor grow inside the liquid and move along with it. When the pressure returns above the vapor value the bubble collapses, and the pressure can locally achieve very high values, up to 7000 bars (Kumar & Saini, 2010). Moreover, if the bubble was confined also by the solid wall of a blade, the solid particles suspended in the fluid can be transported by the fluid ones and hit the solid wall at very high velocity, generating erosion. Cavitation is also the source of high frequency noise, ve…

Assessment of the Usability and Accuracy of the Simplified One-Diode Models for Photovoltaic Modules

2016

Models for photovoltaic (PV) cells and panels, based on the diode equivalent circuit, have been widely used because they are effective tools for system design. Many authors have presented simplified one-diode models whose three or four parameters are calculated using the data extracted from the datasheets issued by PV panel manufactures and adopting some simplifying hypotheses and numerical solving techniques. Sometimes it may be difficult to make a choice among so many models. To help researchers and designers working in the area of photovoltaic systems in selecting the model that is fit for purpose, a criterion for rating both the usability and accuracy of simplified one-diode models is p…

A small scale prototype of a wave energy conversion system for hydrogen production

2015

In this paper a small scale prototype of sea wave energy converter for hydrogen production and storage is presented. Laboratory prototypes of the wave energy converter device and sea water electrolyzer are presented. Experimental results are shown. A cost-effective and efficient power electronics system is designed. Experimental waveforms of the wave energy converter are imported in the power electronics simulation model to simulate the whole system as closely as possible to its effective behavior. Simulation results are shown to test the efficiency of the proposed solution.

Sustainability of the Renewable Energy Extraction Close to the Mediterranean Islands

2017

The aim of this work is to explore the possibility of transitioning a fuel powered island to a renewable powered one. This transition is analyzed for the real MV/LV distribution system of the island of Pantelleria, in the Mediterranean Sea. Particularly, this work is focused on a renewable source nowadays totally unused: wave energy. Thanks to the innovative generator prototype designed by Department of Energy of University of Palermo (Italy), wave energy is able to represent a primary source for the production of electric energy in the Mediterranean islands. The procedures applied in the present article, as well as the main equations used, are the result of previous applications made in di…

Investigating energy saving potential in a big shopping center through ventilation control

2019

Abstract This paper investigates energy saving measures for the ventilation system of large shopping centers. This kind of buildings is characterized by high yearly energy consumptions, because of the high level of operating hours and the frequent use of obsolete technologies. In the analyzed case studies, three big Do It Yourself (DIY) shops, located in Italy, are considered. Two different approaches are considered, they are aimed at reducing the annual energy consumption for the indoor air exchange of the sales area. The first considered retrofit solution consists in the installation of heat recovery exchangers, reducing the energy demand for the air thermal treatment without changing the…

Assessment of bioenergy potential in Sicily: a GIS-based support methodology

2008

Abstract A Geographical Information System (GIS) supported methodology has been developed in order to assess the technical and economic potential of biomass exploitation for energy production in Sicily. The methodology was based on the use of agricultural, economic, climatic, and infrastructural data in a GIS. Data about land use, transportation facilities, urban cartography, regional territorial planning, terrain digital model, lithology, climatic types, and civil and industrial users have been stored in the GIS to define potential areas for gathering the residues coming from the pruning of olive groves, vineyards, and other agricultural crops, and to assess biomass available for energy cu…

Description of hysteresis of Nickel Metal Hydride Battery

2012

A Dynamic Preisach Model for the description of the hysteresis in Nickel Metal Hydride Battery is presented. Both the hysteresis and the dynamical features of charging and discharging cycles are described. The identification of the model is obtained by using a neural network technique developed for magnetic systems. The model is validated by some experimental tests on commercial batteries.

Energy Saving in Public Transport Using Renewable Energy

2017

Hydrogen produced by renewable sources represents an interesting way to reduce the energetic dependence on fossil fuels in the transportation sector. This paper shows a feasibility study for the production, storage and distribution of hydrogen in the western Sicilian context, using three different renewable sources: wind, biomass and sea wave. The objective of this study is the evaluation of the hydrogen demand, needed to replace all diesel supplied buses with electrical buses equipped with fuel cells. An economic analysis is presented with the evaluation of the avoidable greenhouse gas emissions. Four different scenarios correlate the hydrogen demand for urban transport to the renewable en…

A novel implicit correlation for the operative temperature of a PV panel

2012

Abstract The operating temperature of a commercial PV panel strongly affects the electric power output of the devices. The prediction of the operating temperature therefore plays a central role in the economic and energy assessment of PV systems. The authors propose a new implicit correlation that takes into account the standard weather variables but also the regimen of PV panel in terms of the proximity to the maximum power points. Data coming from an experimental setup were processed by using the least squares technique. To validate the reliability of the correlation, a comparison between expected values and data from other common correlations were done. The results show that the regimen …

Assessment of Renewable Sources for the Energy Consumption in Malta in the Mediterranean Sea

2016

The main purpose of this paper is to analyze the energy production in the Maltese islands, focusing on the employment of renewable energies in order to increase their energy independence. The main renewable source here proposed is wave energy: thanks to a strategic position, Malta will be able to produce electrical energy using an innovative type of Wave Energy Converter (WEC) based on the prototype of a linear generator realized by University of Palermo. The use of this new technology will be able to cut down the electrical energy production from traditional power plants and, consequently, the greenhouse gas emissions (GHG). Wave energy source and off-shore photovoltaic (PV) technology are…

A magnetostrictive generator for sensors network

2017

In this paper we present a vibration harvesting electric power generator based on magnetostrictive effect for sensors network in hazardous area and we validate it experimentally. The generator has been designed by using Dynamic Preisach hysteresis Model (DPM). DPM is a development of classical Preisach Model which is able to include dynamical features in the mathematical model of hysteresis. We measure the output power capability of the generator and we estimate its power density generation capability.

Renewable energy sources to fulfill the global energy needs of a country: The case study of Malta in Mediterranean Sea

2016

The paper shows the advantages using different energy resources for the islands of Malta. Moreover, this work is focused on the analysis of the wave energy potential along Malta's coasts. This important resource can be exploited to produce electrical energy using an innovative Point Absorber based on a new generator prototype realized by University of Palermo. The use of renewable source will reduce greenhouses emissions and increase the energy independence of Malta. The procedures applied in the present article, as well as the main equations used, are the result of previous applications made in different technical fields that show a good replicability [1]-[7].

Energy and Economic Analysis of Different Buildings Constructed with Environmentally Sustainable and Traditional Materials

2013

The use of bioclimatic principles can reduce energy demands and CO2emissions in the building sector. Costs are one of the most important barriers to a widespread adoption of the green architecture e.[ The aim of this study is to compare the energy and economic performances of two buildings: a real residential bioclimatic building located in Cinisi (a small town near Palermo, Sicily) and an imaginary residential building supposed having the same geographical location, cubature, shape and orientation as the bioclimatic building but built by conventional building materials. The tools used for this study were TRNSYS and HOMER[

A Innovative Monitoring Underwater Buoy Systems (MUnBuS) for Marine and Rivers installation with IR-Cam, Instrumental Telemetry and Acoustic Data Acq…

2015

The proposed low cost systems shows the results obtained in the implementation and testing in marine environment of a Innovative Monitoring Underwater Buoy Systems for Marine and Rivers installation with IR-Cam, Instrumental Telemetry and Acoustic Data Acquisition Capability (MUnBuS). This concerning a innovative Monitoring Underwater Buoy Systems that can be remotely controlled from the ground, air, satellite and sea and from a Center of Supervision Telecontroller And Data Acquisition and Monitoring (Mobile-STADAM Center). The Buoy is hosts for the radio or satellite communication equipment, the downloading and telemetering data equipment and the photovoltaic power supply, board and underw…

Flexibility Services to Minimize the Electricity Production from Fossil Fuels. A Case Study in a Mediterranean Small Island

2019

The design of multi-carrier energy systems (MESs) has become increasingly important in the last decades, due to the need to move towards more efficient, flexible, and reliable power systems. In a MES, electricity, heating, cooling, water, and other resources interact at various levels, in order to get optimized operation. The aim of this study is to identify the optimal combination of components, their optimal sizes, and operating schedule allowing minimizing the annual cost for meeting the energy demand of Pantelleria, a Mediterranean island. Starting from the existing energy system (comprising diesel generators, desalination plant, freshwater storage, heat pumps, and domestic hot water st…

Wave Energy Assessment along Sicilian Coastline, Based on DEIM Point Absorber

2017

The use of renewable energy sources is one of the most relevant goals to be achieved in order to match the climate protection targets. As a case study, the paper shows the current electrical energy production by sources in the Sicilian context. Among the renewable energy sources, the paper investigates the wave energy potential along the Sicilian coasts, because of the favorable climate around the island. A point absorber is present in order to exploit this source. Two scenarios are presented, with two different levels of energy production.

Description of Hysteresis in Lithium Battery by Classical Preisach Model

2012

In this paper Preisach Model is applied to obtain a mathematical model of the hysteresis in lithium battery. Preisach Model allows to describe the hysteresis of charging and discharging cycles in a lithium battery. The identification of the model is obtained by using a neural network technique developed for magnetic systems. The model is verified on some experimental tests on commercial batteries.

Grid Stability Improvement Using Synthetic Inertia by Battery Energy Storage Systems in Small Islands

2022

In this paper, the synthetic inertia need of the small island of Pantelleria in the Mediterranean Sea is assessed. Firstly, the optimal renewable energy mix able to minimize the Levelized Cost of Energy for the generation system of the island is evaluated, considering the yearly load demand and the characteristics of the local natural resources. The optimal energy mix introduces in the island a quota of power generation with static power converters interfaced to the grid that could jeopardize the security of the system if not suitably controlled. Therefore, the inherent inertial response of the diesel generators of the system is calculated hour by hour for each month of one year, considerin…

Design and Test of a Thermomagnetic Motor Using a Gadolinium Rotor

2013

This paper presents a Thermomagnetic Motor, whose design of the motor is based on a thermal-magnetic coupled dynamic model, which models its magnetic as well thermal properties (magnetic permeability and thermal conductivity). The thermal processes are supposed to be influenced by the thermal conductivity, the convection and the advection. An analytical expression of the generated torque, which links this quantity to the magnetic, thermal and geometrical parameters of the generated torque is given. A design of a machine, based on this theory is proposed and the related performances are numerically simulated. An experimental verification of the performances is reported.

The Recent Change in the Italian Policies for Photovoltaics: Effects on the Energy Demand Coverage of Grid-Connected PV Systems Installed in Urban Co…

2016

In July 2013, the Italian photovoltaic (PV) support policies changed the feed-in tariff (FIT) mechanism and turned to a tax credits program, which is currently in force. The aim of this paper is to investigate how such a radical change has influenced the electricity demand coverage of the PV systems installed in urban contexts. A methodology, which connects the economic assessment to a detailed architectural and energy suitability analysis, was applied to some case studies to analyse the relationships between the physical parameters related to multi-storey buildings (roof shapes, number of floors and area of flats) and the most relevant economic and financial features affecting the viabilit…

A case study to the Evaluation of Global Environmental Quality, concerning thermal, acoustic and atmospheric conditions of urban areas

2013

In this paper we propose an operative procedure aimed at assessing and check the global environmental quality in the urban areas. This methodology is set up by using an ergonomic approach that analyses the interaction man-environment in terms of cause-effect and uses information and data from various sources contributing to the formation of discomfort degrees.[1-2] The representation technique by normo-grams is used for showing some applications executed along the urban territory of Palermo and allows to evaluate very simply all the parameters involved in human comfort. This paper is divided in 5 sections, after the introduction in section 2 a review of the principal simple and complex inde…

Small Wind Technology Diffusion in Suburban Areas of Sicily

2015

Among renewable energy resources, wind energy became more attractive in the last decade. Wind farm installations dramatically increased in areas where climatic conditions, topography, and environment have allowed their development. The installation of wind turbines, usually carried out in remote areas, recently began to cover areas identified by a complex terrain such as urban and suburban zones. Although these new plant choices are characterized by lower productivity, there is increasing interest in wind energy production in both urban and suburban areas. In this work the authors have carried out an energy analysis developed from a sample of small wind turbines available on the market. Thi…

Sustainable development in urban transport: Feasibility study for a plant to produce and store hydrogen from wind energy in the urban transport in We…

2005

Mini Wind Plant to Power Telecommunication Systems: A Case Study in Sicily

2012

The ever increasing problems related to air pollution and the difficulties for power lines to reach inaccessible areas are pushing to find new solutions for powering telecommunications equipments (TLC). The renewable energy systems, although relatively expensive, have the required characteristics. The purpose of this work is to find a solution based on a low power wind turbine to serve a real telecommunication site located near Palermo, the main city of Sicily (Italy).

A Ferrite Tubular Linear Permanent Magnet Generator (FTLPMG) analysis and design

2014

Several linear synchronous generators for the exploitation of sea wave energy have been proposed. Such machines do not require reactive power for the magnetization since they use permanent magnets for the excitation. The use of permanent magnets in a rough environment such as the marine environment may be a very weak point in the application of these kind of devices. In order to overcome this difficulty, the authors in this paper propose a linear synchronous electrical generator. Its excitation uses ferrites as suitable solutions to extract energy from sea waves. This paper describes the analysis and design of an improved axially magnetized tubular permanent-magnet machine in which several …

Experimental validation of a distribution theory based analysis of the effect of manufacturing tolerances on permanent magnet synchronous machines

2017

An experimental study on the effect of permanent magnet tolerances on the performances of a Tubular Linear Ferrite Motor is presented in this paper. The performances that have been investigated are: cogging force, end effect cogging force and generated thrust. It is demonstrated that: 1) the statistical variability of the magnets introduces harmonics in the spectrum of the cogging force; 2) the value of the end effect cogging force is directly linked to the values of then remanence field of the external magnets placed on the slider; 3) the generated thrust and its statistical distribution depend on the remanence field of the magnets placed on the translator.

Optimization of cogging force in a linear permanent magnet generator for the conversion of sea waves energy

2015

In this paper an approach to the optimization of cogging force in a linear permanent magnet generator for the conversion of sea waves energy is presented. We have optimized the cogging force of a linear permanent magnet generator by using a 3D FEM parametric simulation. Several possible design solutions have been computed. A generator has been built and the results of the minimization procedure has been experimentally validated.

Sea Wave Energy. A Review of the Current Technologies and Perspectives

2021

The proposal of new technologies capable of producing electrical energy from renewable sources has driven research into seas and oceans. Research finds this field very promising in the future of renewable energies, especially in areas where there are specific climatic and morphological characteristics to exploit large amounts of energy from the sea. In general, this kind of energy is referred to as six energy resources: waves, tidal range, tidal current, ocean current, ocean thermal energy conversion, and saline gradient. This review has the aim to list several wave-energy converter power plants and to analyze their years of operation. In this way, a focus is created to understand how many …

Design and experimental test of a low costweather buoy

2013

The importance of prevention plans based on realistic inundation scenarios was dramatically highlighted by the Indian Ocean Tsunami of 26 December 2004. But also in the Mediterranean, sea storms basin are a quite common event especially during winter months. These scenarios are generally based on numerical models of tsunami wave propagation that can become more realistic and effective when calibrated with the distribution of true data acquired by special weather buoy. In this paper we present the result of an experimental weather buoy built by DEIM of University of Palermo, that is characterized by small cost and big versatility.

Energy Savings through Integration of the Illumination Natural and Artificial, Using a System of Automatic Dimming: Case Study

2013

The reduction of electrical energy consumption in buildings is a subject of great interest in the international scientific community. In buildings with a lot of available natural light, designed with large glazed surfaces, the artificial lighting system is often oversized and cannot be divided into segments to meet lighting demands during daylight hours.This article presents an experimental study, conducted in a university lecture hall that has a glazed surface covering the whole wall at one end, which provides a level of internal illumination that is only sufficient for the area next to the window itself, even when the outside lighting conditions are very bright. It is therefore necessary …

First analyses on a mechanical motion converter to produce electrical energy from sea wave

2020

The exploitation of sea wave opens new horizon for suppling small islanded communities. With this goal the paper propones a prototypical device for the utilization of sea wave along the coastline. The device is based on a mechanical motion conversion, from an alternative rotation into unidirectional rotation in order to run commercial generators. First evaluations are here reported, demonstrating the feasibility of this solution.

Numerical simulation of a wawe generator: A case of study

2013

The aim of present work is the numerical simulation of a linear generator, capable of directly converting the kinetic energy, available by the wave, into electrical energy, through the device linear motion (up and down). In this paper, we intend to propose a numerical simulation approach to immersed devices by applying the Immersed Boundary Method. The Theory of linear wave is used to study and reproduce sea conditions and the computational domain is created based on observations available for the site in which it is envisaged the positioning of the device.

A Planar Generator for a Wave Energy Converter

2019

This article presents a permanent magnet planar translational generator which is able to exploit multiple modes of sea wave energy extraction. Linear electrical generators have recently been studied for the exploitation of sea wave energy, but, to the best of our knowledge, no synchronous planar translational generator has been proposed. In this article, to maximize the energy extraction, we have considered all the potential modes of motion due to wave excitation and included them within the mathematical model of the proposed system. The principle of operation of the generator can be summarized as follows: the moving part (translator) of the generator is driven from the sea waves and induce…

The importance of reliable climatic data in the energy evaluation

2012

Abstract In the last few years, more and more attention has been focused on energy issues, as it is pointed out, for example, by the Directive 2002/91/EC on the Energy Performance of Buildings and Directive 2009/28/EC on the promotion of the use of energy from renewable sources. However, in order to do that, reliable tools for technicians to design systems for such topics should be provided. Nowadays, several software are available; the weak point is the availability of reliable climatic data and, above all, the ones referring to solar radiation. In this work, after a short overview of the world climatic databases, a description of three statistical methods for the elaboration of a climatic…

A multiphysics approach to the design of a seawave energy conversion system

2008

This paper presents a multiphysics approach to the design of a seawave energy conversion system which consists of a both a permanent magnet linear generator directly coupled to sea waves and the related power electronics conversion system. The thermal, electromagnetic and circuital aspects are included in the proposed approach. In order to maximize energy extraction, the stochastic features of the energy source is considered in the mathematical model of the whole system. An optimization procedures which includes the stochastic features of the model is presented and a machine built on the basis of the results of this procedure is shown.

Design and Experimental Test of a Thermomagnetic Motor

2012

Abstract This paper presents a Thermomagnetic Motor. The design of the motor is based on a thermal-magnetic coupled dynamic model, which is obtained by assuming the use of a ferromagnetic material working at temperatures near the curie point. The motor is modeled in terms of both its magnetic as well thermal properties (magnetic permeability and thermal conductivity) and the thermal processes are supposed to be influenced by the thermal conductivity, the convection and the advection. An analytical expression of the generated torque, which links this quantity to the magnetic, thermal and geometrical parameters of the generated torque is given. A design of a machine, based on this theory is p…

The role of the effect of manufacturing tolerances on a tubular linear ferrite motor

2015

Electric machines are often designed without considering workmanship and materials tolerances. Their manufacturing process involves a series of steps, starting with raw materials and ending with the machine assembly. In each of these steps occur deviations due, for instance, to mistakes in positioning tools or to the tolerances in the electrical and magnetic characteristics of the materials. These deviations may cause unwanted parasitic effects such as torque ripple, losses or acoustic noise. Such effects have to be considered especially in machines used in industrial drives for high performance applications. Moreover the tolerances in the magnetic materials have a considerable effect on th…

Hydrogen from The Sea: The Challenge of the Future. Present and Future Developments

2014

In this paper we proposed the use of saline water to product hydrogen. As far as using saline water, can be proposed two different scheme and technology. The aim of this work is to design an electrolyze system capable of utilizing sea water for direct electrolysis. It is probable that these systems would operate at a low power density and electrolyze only a small portion of the water in contact with electrodes. In particular, we present the results obtained by two different prototype of electrolyzer: one with steel electrodes and the second electrodes with titanium. Further experiments were carried out by changing the electrolytic solution of water and sodium chloride in real seawater. Fina…

A Case Study to evaluate the indoor global quality

2013

This paper proposes two complementary procedures for assessing the global quality comfort: the first one, prevalently objective, is based on the acquisition of microclimate measured data and computed subjective values; the second one, that is purely subjective, uses a questionnaire drawn from the ISO/DP 10551 Recommendation. An application to some lecture-halls and laboratories of the school is here showed.

Power Conversion System for Improved Linear Generator in sea wave energy harvesting applications

2020

Nowadays, many islands worldwide are lack of electrical energy. Thus, it is convenient to exploit available renewable energy sources, among which sea waves near the islands. This paper focuses on the power conversion system coupled with an offshore wave energy device, such as an improved linear generator, to be used for sea wave energy harvesting. Particularly, the design of the linear generator has been proposed to improve the energy efficiency of the entire system. The proposed power conversion system is composed by two Boost Rectifier (BR) directly coupled to the linear generator, and one Voltage Source Inverter (VSI), which it is used as front-end between the DC-bus and the grid. The pr…

A innovative laterals hydro floating tilting systems for USV or surface nautical vehicles

2015

The proposed project shows the results obtained in the implementation and testing in lacustrine and marine environment of an innovative laterals hydro floating tilting systems control for USV or remote/autonomous surface nautical vehicles. This vehicle is based on a pending patent belonging to Palermo University (Patent Pending RM2012A000209 and RM2012A000209). The system allows, during operation as a vehicle USV, set changes sailing trim and make turns with very narrow angle with little shunting movements. In fact the main benefits obtained were able to change or adjust the navigation structure by changing the tilt of one or two hydro floating during navigation without intervening directly…

Near zero energy island with sea wave energy: The case study of Pantelleria in Mediterranean Sea

2016

In this paper the authors present a study of the transition of an energy generation system for a real MV/LV distribution system from one that is "fuel-based" to a "renewables-based" system in particular from sea wave energy, using the data acquired from an innovative generator prototype realized by University of Palermo. The study is carried out for a real islanded network located in the Island of Pantelleria (Mediterranean Sea). The procedures applied in the present article, as well as the main equations used, are the result of previous applications made in different technical fields that show a good replicability [1]-[7].

Introduction of Offshore Wave, Wind and Solar Energies in Vietnam

2020

In Vietnam, the energy demand shows an ever-increasing trend. To limit the utilization of fossil fuels and the following consequences for the environment, renewable energy sources must be adopted. In this context, the paper assesses the utilization of offshore wind and sea wave, by considering a commercial wind turbine and a prototypical wave energy converter. Solar energy can be optionally also collected by this device. An algorithm is introduced to find the best composition of the three sources able to cover a desired share of energy demand. The approach is applied to Ca Mau, a province in the southern part of Vietnam. Finally, the results encourage the adoption of these energy sources th…

Renewable energy sources: a Mediterranean perspective

2010

Southern Mediterranean countries are growing very fast. Globally, the evolution of economic and social indicators in the area is positive, since significant progresses have been registered in the field of economic as well as human development.

A Preliminary Energy Assessment to Improve the Energy Sustainability in the Small Islands of the Mediterranean Sea

2020

Power plants supplied by renewable energy sources are expanding around the world, in order to reduce the carbon dioxide emissions, limit the global warming and improve the energy sustainability. Despite the relevant achieved results, small islands are heavily reliant on fossil fuels. In this context, renewable energy sources are available but practically unused, due to landscape and economic constraints. This condition is quite common in the Mediterranean Sea. These islands are normally fed by a stand-alone electrical grid and a power plant, equipped with diesel engines. In order to improve the sustainability of the energy sector, the paper considers the case study of Ustica, a small Italia…

Energetic Sustainability Using Renewable Energies in the Mediterranean Sea

2016

The paper is focused on the analysis of the electrical energy sector in the Maltese islands, focusing on the employment of Renewable Energies in order to increase its energy independence. The main renewable source here proposed is wave energy: thanks to its strategic position, Malta will be able to generate electrical energy through the use of an innovative type of Wave Energy Converter (WEC) based on the prototype of linear generator designed and developed by the University of Palermo. This new technology will be able to cut down the electrical energy production from traditional power plants and, consequently, the greenhouse gas emissions (GHG). Wave energy source and off-shore photovoltai…

A Magnetostrictive Electric Power Generator for energy harvesting from traffic: Design and experimental verification

2015

In the last decades, the growth in energy demand, the decrease of fossil fuels available in the market and the impact of anthropogenic factors on climate change has given new impulse to research on renewable energy systems, particularly those known as energy harvesting devices (EHDs) [1]. A large number of EHDs have been proposed, using different operating principle [1-4]. Among them, piezoelectric and magnetostrictive seem to be particularly suitable for the application in EHD. In these materials the application of external mechanical stress induces a change in the level of magnetization and therefore an electromotive force (emf) can be generated and collected in order to produce electrica…

Indoor Environmental Quality Survey: A Brief Comparison between Different Post Occupancy Evaluation Methods

2013

Building occupants are important factor in giving information on indoor conditions such as comfort, productivity, building performance and occupants ́ health. Even that, being their appraisal mainly based on subjective judgments, it is difficult to set up a standard and objective method for this purpose. The present work aimed to describe, analyze and compare the most common tests on this topic, in order to highlight critical, failings and strengths.

A innovative semi-immergible USV (SI-USV) drone for marine and lakes operations with instrumental telemetry and acoustic data acquisition capability

2015

The proposed project shows the results obtained in the implementation and testing in lacustrine and marine environment of a nautical remote controlled vehicle with surface navigation and innovative features Semi-Immersible (SI-USV). This vehicle is based on a pending patent belonging to Palermo University (Patent Pending RM2012A000209 and RM2012A000209) concerning innovative semi-immersible vehicles (SI-Drone), that can be remotely controlled from the ground, air, satellite and sea also during the semi-immersible operation. The vehicle with electric power is coupled with a jet propulsion, given the low draft, makes it possible to navigate in shallow waters or coastal shipping or sandbars. T…

A security and surveillance application of the innovative Monitoring Underwater Buoy Systems (MUnBuS) on the Protected Marine Area (AMP) of capo gall…

2015

The proposed low cost systems shows the results obtained in the implementation and testing on real security application to Protected Marine Area surface and submarine environment of a innovative Monitoring Underwater Buoy Systems (MUnBuS) for installation with IR-CCTV-Cam, ultrasonic dolphin warning system and Green Laser Perimeter Detection. This concerning innovative Monitoring Underwater Buoy Systems that can be remotely controlled from the ground, air, satellite and sea and from a Center of Supervision Telecontroller And Data Acquisition and Monitoring (Mobile- STADAM Center). The Buoy is hosts for the radio or satellite communication equipment, the downloading and telemetering data equ…

The use of sea waves for generation of electrical energy and Hydrogen

2009

Recently linear synchronous generator for the exploitation of sea wave energy has been proposed. That solution does not require reactive power to magnetize but needs permanent magnets to assure the excitation. The electrical energy generated by such a device must be converted and conditioned in order to match the instantaneous utility requirements and a power link from the sea to an interconnection is needed. In this paper in order to overcome that difficulty, the authors propose the use of the electrical energy generated to generate “in situ” hydrogen. As a result the output of the generation would be hydrogen that can be stored and used when needed The proposed electrical generator is a P…

Design of wave energy converter (WEC): A prototype installed in Sicily

2015

The purpose of this work is to describe a possibility of installation of a wave converter in Sicily, in the Mediterranean Sea. In this paper we present the design of buoyant electrical generator, in particular, wave linear permanent magnet generator which can make wave energy converted to electrical energy.

A linear generator for a waveroller power device

2017

In this paper experimental tests on a small scale tubular linear generator to be applied to wave rollers device are presented. A reduced scale of gnerator is presented and experimental results obtained in on test bench are shown. Experimental waveforms of current and voltage are recorded. Simulation results are compared to the experimental ones in order to validate the mathematical models used.

Evaluation of the optimal renewable electricity mix for Lampedusa island: The adoption of a technical and economical methodology

2020

Abstract Worldwide, the majority of small islands not connected to the main grid is still dependent on fossil fuels. From an economic and environmental point of view, this condition is no more sustainable given the high costs for electricity generation and the high level of pollutant emissions. Furthermore, the dependence on fossil fuel represents a risk for the security of the supply of several small developing Countries since they are obliged to import those resources from foreign Countries. The introduction of renewable energy sources in small islands represents a valid solution to solve these problems. In this context, the paper investigates the case of Lampedusa, a small Italian island…

Stability Analysis in a Vietnam Small Island for the Deployment of a Nearshore Wave Power Plant

2022

The requirement for a more sustainable energy mix is promoting the spreading of technologies supplied by renewable sources. However, the introduction of unprogrammable energy sources in small electrical grids could jeopardize the stability of the entire system. In this context, the paper analyses a small island in Vietnam, assessing the effects due to the installation of a new power plant supplied by sea wave energy. While the installation of this technology could represent a great opportunity to reduce the local energy dependence, on the other side the quality of the supply could be worsened. Solutions are assessed to allow a good network service.

A renewable energy mix to supply small islands. A comparative study applied to Balearic Islands and Fiji

2019

Abstract Power plants supplied by renewables are expanding around the world, increasing the sustainability of the energy sector. In this context, small islands are heavily reliant on fossil fuels. However, this paper shows that the same problem can be found also in small islands belonging to developed countries. To increase the energy sustainability of small islands, the authors assembled a simplified mathematical approach to evaluate the potential electricity production, exploiting the local available energy sources: solar, wind and sea wave. The mathematical model requires few information in input, such as climatic data about the local energy sources and technical features on the selected…

Nexus Water & Energy: A Case Study of Wave Energy Converters (WECs) to Desalination Applications in Sicily

2016

The recent studies about interactions among energy and water are considered as a new field of research. As almost all energy generation processes require significant amounts of water, and water requires energy for treatment and transport, so these two resources are inextricably linked. The main aim of this work is a presentation of the use of renewable energy for desalination plants in Sicily: in particular exploitation of wave energy into electrical energy necessary for water treatment. Desalination is the most energy intensive water treatment technology but it could be solution for many problems in water supply for areas with chronic debt of water. In this study we find three section: in …

Sea water desalination and energy consumption: A case study of wave energy converters (WEC) to desalination applications in sicily

2016

Recent studies about interactions among energy and water are considered as a new field of research. As almost all energy generation processes require significant amounts of water, and water requires energy for treatment and transport, so these two resources are inextricably linked. The main aim of this work is a presentation of the use of renewable energy for desalination plants in Sicily: in particular exploitation of wave energy into electrical energy necessary for water treatment. Desalination is the most energy intensive water treatment technology but it could be solution for many problems in water supply for areas with chronic debt of water. The aim of this work is a description of a s…

A procedure to evaluate the indoor global quality by a sub objective-objective procedure

2013

This paper proposes two complementary procedures for assessing the indoor global comfort: the first one, prevalently objective, is based on the acquisition of microclimate measured data and computed subjective values; the second one, that is purely subjective, uses a questionnaire drawn from the ISO/DP 10551 Recommendation. An application to some lecture-halls is here showed

Electro-optical characterization of ruthenium-based dye sensitized solar cells: A study of light soaking, ageing and temperature effects

2017

Abstract In this work, we report on the electro-optical characterization of Dye Sensitized Solar Cells (DSSCs) which use ruthenium complexes as sensitizers. In particular, several kinds of measurements have been performed to study the electrical performances and the efficiency levels of the cells at different operating conditions. In detail, the measurements have been conducted at varying temperatures and hours of light soaking. Our results show that the short circuit current density J SC , the open circuit voltage V OC and the conversion efficiency η increase with the hours of light soaking, while they decrease with temperature. A thorough investigation on the light soaking process at the …

Energy and Economic Comparison of Different Conditioning System among Traditional and Eco-Sustainable Building

2013

The use of bioclimatic principles can reduce energy demands and CO2 emissions in the building sector [1-. Costs are one of the most important barriers to a widespread adoption of the green architecture technologies [4-. The aim of this study is to compare the energy and economic performances of two buildings: a real residential bioclimatic building located in Cinisi (a small town near Palermo, Sicily) and an imaginary residential building supposed having the same geographical location, cubature, shape and orientation as the bioclimatic building but built by conventional building materials. The tools used for this study were TRNSYS and HOMER

Guidelines proposal for a good and durable WEC design

2017

In this paper, preliminarily a proposal for design guidelines for a “good” design of wave energy converter is presented and successively a small scale prototype of a wave energy converter including the buoyant electrical generator, the power electronics equipment and a sea water electrolyzer is designed on the basis of these guidelines and presented.

Analysis of interconnection substations for sewave power farms

2014

In this paper we analyse the interconnection of a seawave power farm to the grid. The generator type used in the farm is a linear synchronous generator driven from the seawaves that generates, highly distorted emfs. We presents two possible ways to interconnect the farm to the grid. One is based on an approach where for each generator there is a conversion subsystem that permits the direct connection of each generator to the a.c. network, the other one is based on an a.c.-d.c. converter that is connected to the generator, the converter is connected to a dc link that can receive the power from every unit and that can supply a dc-ac converter directly connected to the main.

Flexibility Services in a Mediterranean Small Island to Minimize Costs and Emissions Related to Electricity Production from Fossil Fuels

2020

In last years, the energy efficiency in non-interconnected islands became an important topic, since the electricity production is often based on diesel generators, thus contributing to the global warming. Italian government recently emitted two decrees to promote the introduction of renewable energy technologies in 21 non-interconnected islands, both for electrical and thermal uses. In this paper, the economic and environmental feasibility of the introduction of renewable energies in the island of Pantelleria was assessed adopting an optimization approach. Furthermore, the flexibility provided from the local desalination plant and the domestic water heaters was evaluated. The final demands …

First Life Cycle Impact Considerations of Two Wave Energy Converters

2018

The work presents two different revolutionary devices for the utilization of a new entry of renewable energy sources: sea wave. The first technology is based on linear generators, able to directly converts a linear motion into electrical output, limiting to minimum the chain of energy conversion. The other solution is based on a mechanical motion converter, coupled with alternators. The scope of this paper is to compare the two different systems designed by University of Palermo, through Life Cycle Assessment, in order to evaluate the global effects of the two systems to the environment.

A Permanent Magnet Linear Generator for the Enhancement of the Reliability of a Wave Energy Conversion System

2019

In this paper, a linear generator for a highly reliable Wave Energy Conversion system is designed and tested. In order to store energy, the system is able to produce hydrogen The Wave Energy Conversion System consists of an electrical linear generator, a power conversion system and a sea-water electrolyzer. A small scale prototype of the system has been designed and built. The design is oriented to the enhancement of the system robustness and reliability and a Failure Mode and Effects and Criticality Analysis (FMECA) has been used. In order to guarantee an easy extension of the power capability of the marine plant, a modular architecture of the system has been adopted. The design strategy i…

Identification of the inertial model for innovative semi-immergible USV (SI-USV) drone for marine and lakes operations

2015

The proposed project shows the results obtained in the implementation and testing in lacustrine and marine environment of a nautical remote controlled vehicle with surface navigation and innovative features Semi-Immergible (SI-USV). This vehicle is based on a pending patent belonging to Palermo University (Patent Pending RM2012A000209 and Patent RM2014Z000060) concerning innovative semi-immersible vehicles (SI-Drone), that can be remotely controlled from the ground, air, satellite and sea also during the semi-immersible operation. Given its low draft, the electric powered vehicle, coupled with jet propulsion, makes it possible to navigate in shallow waters, coastal shipping or sandbars.

Improving energy efficiency of commercial buildings by Combined Heat Cooling and Power plants

2020

Abstract Commercial buildings play a key-role in the energy consumption of the building sectors. Recent statistics have shown that as the number of commercial buildings is continuously increasing, their effects on energy consumption are expected to grow. These buildings are characterized by high energy demand mainly due to lighting and HVAC requirements. Rooms of energy saving exist by considering that: (i) electricity demands and HVAC requirements occur simultaneously during the day and (ii) both demands are currently satisfied by using separate energy systems. It is apparent that the adoption of polygeneration systems could represent a valid solution to achieve energy savings. To this aim…

Metodologie di analisi energetica nei supermercati e negli ipermercati, con l’obiettivo della ottimizzazione della domanda elettrica ed energetica gl…

2004

Design of a transverse flux machine for power generation from seawaves

2013

Linear electrical generator has been recently studied for the exploitation of sea wave energy, however the definition of the optimum geometry to be used is still debated and due to the fact that seawave energy is characterized by low speed and very high forces, a generator which is able to convert energy at low speed and high force is needed. In this paper we investigate the possibility to use a transverse flux linear generator (TFG) because transverse flux technology presents the highest force density per volume index among the iron based electrical machines. The advantages of TFG topology against the classical longitudinal concept are [1]: (a) the magnetomotive force per pole is independe…

Desalination by sea wave in small islands: The case of study of Lampedusa (Italy)

2018

The paper analyses the theme of water energy nexus, investigating a specific industrial process: desalination. In particular, the paper reports a case of study, applied in the small island of Lampedusa, located at south of Sicily (Italy). As the many small islands in the middle of the Mediterranean Sea, Lampedusa presents a small electrical grid, not connected to the mainland. The electrical production is entrusted to old diesel engines, consuming fossil fuel, transported by boat from Sicily. Besides, the renewable energy sources are extremely underdeveloped in this territory, since the environmental constraints make complex the use of technologies, like wind turbines or photovoltaic panels…

Dynamic Preisach hystersis model for magnetostrictive materials for energy application

2013

Recently Magnetostrictive materials have been proposed as active materials to be used in several energy harvesting technology [1]. In this kind of application, the working condition of the material is highly dynamic and non linear. As a result static models of magnetostrictive materials are usually not very accurate and can be not reliable to develop a sufficiently accurate designof the energy harvesting devices. The presence of hysteresis requires accurate mathematical modeling in order to correctly foresee the behavior of real materials (ferromagnetic or magnetostrictive) used in control systems or in electrical machines and thus simplifying the design of such controllers or predicting wi…

La climatizzazione estiva degli edifici con l'impiego di energia solare. Criteri di ottimizzazione progettuale nelle applicazioni in area Mediterranea

2005

Optimized design of a sea wave energy conversion system

2008

“UPDATE ON DESICCANT WHEEL MODEL”.

2004

The paper present the update on the desiccant wheel models, developed earlier by the authors

Reduction of cogging force in linear generators for wave energy harvesting

2022

Due to huge energy potential of sea waves, many technologies have been proposed in the last few years. Some concepts have been developed and sometimes also tested in the open sea. Some prototypes use linear generators to directly convert the vertical motion of buoys into electrical energy. This solution minimizes the numbers of energy conversion steps, increasing the energy efficiency. At the same time, the limited numbers of components could also increase the reliability of the wave energy converter. For this reason, the development of linear generators is considered with great interest. This paper investigated the cogging force, a magnetic force due to the interaction between the magnets …

Electrical Power from seawave energy

2010

Current energy crisis and general concerns on environmental issues have triggered an ever increasing effort on harvesting renewable energies. Amongst renewable energy sources, sea wave energy is definitely the one that has been less utilised. This is probably caused by three reasons: i) the low energy concentration in the sea waves, at least in the sites where it is technically possible to install conversion stations: ii) the strong technical novelties that are required to extract the energy that is contained in a highly and stochastically variable motion; iii) the difficulty to find a suitable electrical system able to convert the energy contained in the motion of the sea into electrical e…

Indagine tecnica ed economica per lo sfruttamento ai fini energetici dei tralci di potatura della vite

2008

Il binomio energia rinnovabile-idrogeno per il fabbisogno energetico di un complesso residenziale. Valutazioni di carattere tecnico-economico

2005

Studio di fattibilità ed analisi tecnico-economica di un parco eolico per la produzione di elettricità ed idrogeno in un comprensorio montano

2006

“La climatizzazione estiva degli edifici con l’impiego di energia solare. Analisi di un caso studio in area Mediterranea”

2005

Sea wave energy to supply the Aeolian Islands in sustainable way

2018

The diffusion of technologies supplied by Renewable Energy Sources is contributing in the challenge of reduction of energy dependence from fossil fuels, avoiding the emission of several polluting substances and greenhouse gases. Despite the technological development and important results around the world, in several remote areas or small islands the electrical energy production is based on obsolete technologies, supplied by fossil fuels. This solution is not sustainable for the environment, as the emissions of several pollutants. Focusing the attention on small islands, these areas usually have a standalone grid, as the high cost to build an electrical connection to the mainland, in compari…

Investigating Energy Saving Potential in a Big Shopping Centre through Ventilation Control

2018

This work shows an example of energy saving interventions on the ventilation system of a big shopping center. This kind of buildings is characterized by high energy consumptions, because of the high level of yearly operating hours and the use of obsolete technologies. In the case study, a big Do It Yourself (DIY) shop located in the southern part of Italy is analyzed, proposing two different approaches aimed at reducing the annual energy consumption for the indoor air exchange of the sales area. In the AS-IS scenario, a centralized HVAC plant, composed by six rooftops, is installed on the roof of sales area, working with fixed airflow value. The first retrofit solution involves the installa…

Analisi dei parametri antropometrici di etnie diverse ai fini del comfort termoigrometrico indoor

2010

In questo lavoro vengono presentati i risultati di uno studio volto a verificare se l’algoritmo, proposto da P.O. Fanger, relativo allo scambio termico radiativo tra corpo umano ed ambiente indoor, possa essere utilizzato per tutte le popolazioni mondiali: un erronea stima dello scambio termico radiativo può condurre infatti ad una erronea valutazione delle prestazioni di comfort indoor. In queste condizioni risulta pertanto importante valutare, con elevata accuratezza, i parametri coinvolti nel calcolo del flusso termico radiativo tra corpo umano e ambiente indoor circostante, tra i quali ritroviamo quelli dipendenti dalle caratteristiche propriamente geometriche del corpo umano: area proi…

Ottimizzazione energetica e razionalizzazione della domanda elettrica dei supermercati e degli ipermercati.

2005

Studio di fattibilità di un impianto per la produzione e accumulo di idrogeno da energia eolica per trasporto pubblico urbano nella Sicilia occidenta…

2005

Dynamic Preisach Hysteresis Model for Magnetostrictive Materials for Energy Application

2013

UPDATE ON DESICCANT WHELL MODEL

2004

A sustainable energy production: Sea Wave in the small island of Ustica (Italy)

2018

Nowadays the electrical energy production is based on fossil fuels in the greatest part of smaller islands in the Mediterranean Sea. Despite the availability, the renewable energy sources are practically unused, as landscape constraints. So, the paper presents the case of study of Ustica, a small island located at north of Sicily, in the middle of Mediterranean Sea. Starting with the analysis of the electrical energy consumption of public buildings, the paper suggests an energetic scenario, based on solar and sea wave. In particular, in order to use this new resource, the paper presents an innovative wave energy converter. Finally, the energetic and economic evaluations encourage the realiz…

Greening and sustainable energy approach applied for Balearic Islands and Fiji Islands: a comparative study

2018

Renewable energy sources are expanding around the world, with significative results in the electricity generation sector. Despite this, the share of renewable energy sources in small islands is very low, except in rare cases. In this context, the paper analyses the energy mix currently used to produce electricity in the Balearic Islands and the Fiji Islands. These two archipelagos show several differences but have in common the strong energy dependence from fossil fuels. In order to increase the energy sustainability of small islands, a preliminary energy assessment is realized, using climate data collected from GIS-tools and introducing a numerical approach. As target, the Authors consider…

Applicazioni dell'effetto termoelettrico: un caso studio

2010

Riveste sempre maggiore importanza l’utilizzo di fonti rinnovabili di energia da affiancare alle fonti tradizionali, anche per l’ottenimento degli obiettivi sottoscritti con l’adesione al Protocollo di Kyoto. In questo contesto anche tecnologie note per la produzione di energia elettrica ma precedentemente non convenienti - sia per il livello tecnologico dei componenti o per gli elevati costi rapportati all’efficienza ottenibile dai sistemi sviluppabili - potrebbero trovare una adeguata collocazione. Tra queste tecnologie l’effetto termoelettrico potrebbe essere vantaggioso in alcune particolari applicazioni di piccola potenza. I principali sistemi per la produzione di energia elettrica da …

Benefici ambientali derivanti dall’impiego del vettore energetico idrogeno all’interno di un complesso residenziale

2005

Energy and Economic Comparison of different conditioning system among traditional and eco-sustainable building

2013

RISPARMIO ENERGETICO NELL'EDILIZIA

2007

Design and numerical simulation of a magnetostrictive electric power generator.

2013

The product oriented environmental Management Systems (POEMS): an experience in the Sicilian agricultural and food context

2005

Mini Wind Plant to Power Telecommunication Systems: a Case Study in Sicily

2013

The ever increasing problems related to air pollution and the difficulties for power lines to reach inaccessible areas are pushing to find new solutions for powering telecommunications equipments (TLC). The renewable energy systems, although relatively expensive, have the required characteristics. The purpose of this work is to find a solution based on a low power wind turbine to serve a real telecommunication site located near Palermo, the main city of Sicily (Italy).

ANALYSIS OF INTERCONNECTION SUBSTATIONS FOR SEAWAVE POWER FARMS

2014

In this paper we analyse the interconnection of a seawave power farm to the grid. The generator type used in the farm is a linear synchronous generator driven from the seawaves that generates, highly distorted emfs. We presents two possible ways to interconnect the farm to the grid. One is based on an approach where for each generator there is a conversion subsystem that permits the direct connection of each generator to the a.c. network, the other one is based on an a.c.-d.c. converter that is connected to the generator, the converter is connected to a dc link that can receive the power from every unit and that can supply a dc-ac converter directly connected to the main.

Evaluation of an integrated energy system in the Park of Madonie

2018

This paper analyses technical and economic aspects relative to a hypothetical wind farm installed inside the park of Madonie (Sicily) that produces electric energy for the direct use and to supply an electrolytic system for the production of hydrogen. User is formed by approximately 20,000 persons who live in the mountain localities of the park. Global energy required by user was estimated carrying out hypotheses on daily power demand. Discontinuous power makes inescapable to connect wind farm to grid, so that energy demand of user is partially satisfied by means of energy wind, while the remaining part becomes from grid. Surplus of power that turbines make available when wind speed is part…

Design and Test of a Thermomagnetic Motor Using a Gadolinium Rotor

2013

The purpose of this paper is to show that a Thermomagnetic (Curie) Motor [1-3], which can rotate continuously and has useful mechanical characteristics, is feasible. A thermomagnetic motor can directly converts thermal energy into kinetic energy. In this type of motor force is generated by a thermally induced permeability difference in two areas of the rotor, which can generate a force if the rotor is placed in a magnetic field. This force can be enhanced if the hot side temperature of the rotor is above the Curie’s temperature of the magnetic material and the cold side under this temperature Unfortunately, the traditional ferromagnetic materials have very high Curie’s temperature and there…

Benefici ambientali derivanti dall'impiego del vettore energetico idrogeno all'interno del complesso residenziale

2006

Analisi delle potenzialità di risparmio energetico nel settore vitivinicolo. Gestione energetica di un'azienda vinicola della Sicilia occidentale

2008

Il mercato dei condizionatori d’aria nel residenziale ed il loro impatto sui bilanci energetici urbani. Il caso di Palermo

2006

An Approach to the conversion of the power generated by an offshore wind power farm connected into seawave power generator

2011

Environmental benefits due to hydrogen uses in residential buildings

2005

The importance of reliable climatic data in the urban energy policy

2011

In the last years, more and more attention has been focused on energy issues, in particular at urban level, as it is pointed out by the Directive 2002/91/EC on the Energy Performance of Buildings. In fact, the building sector encompasses nearly 30% of the energy whole consumptions. To try to limit such consumptions, both central and local governments should plan effective policies, such as promoting the use of renewable sources and of more energy efficient buildings (e.g. by means of green coverings). But in order to do that, local administrations should provide reliable tools for engineers and technicians to plan such systems. Nowadays, several software are available; the weak point is the…

Design and performances of a high temperature superconducting axial flux generator

2013

An important quality index of electric machine is the power density: it is known that axial flux machine tends to have a higher power density than the radial machines. As a result they are becoming more and more used in applications where the power density is a critical issues. However, the best way to enhance the power density is to increase the value of the airgap field and this could be achieved by using a superconducting excitation. Many projects have been developed in the world in order to develop both superconducting generator and superconducting motor, but in most of these programs the geometry of the machine has been based on radial machines [1]. All of these approaches show the fea…

Condizioni termoigrometriche per la conservazione di beni artistici in ambienti indoor: il museo archeologico Baglio Anselmi di Marsala

2008

I beni artistici, anche se collocati in ambienti chiusi, sono ugualmente esposti ad un processo di degrado che non è possibile evitare ma sul quale si può intervenire per rallentarne il decorso. I materiali che costituiscono un bene variano nel tempo a causa di trasformazioni fisiche, chimiche, biologiche e meccaniche: entro certi limiti di modificazione del bene si parla di invecchiamento, ma se tali limiti vengono superati e viene compromessa la possibilità di fruizione del bene stesso si parla di vero e proprio degrado. Le condizioni ambientali all’interno dei musei dovrebbero, pertanto, essere tali da preservare le opere d’arte dal degrado e da ridurre la frequenza degli interventi di r…

Optimization of a thermoelectric system for power generation

2010

Nowadays the utilization of renewable energy sources is very important to support the traditional ones, and besides in order to achieve the objectives fixed by the Kyoto Protocol. In this context also well known technologies related to the electric energy production, formerly not suitable - due to the technological level of the components or due to the high costs linked to the system efficiency -, may found a suitable collocation. Among these technologies, the thermoelectric effect may be very advantageous in some particular applications of small power. A power generation system utilizing this technology was studied by the Authors. This system utilizes the thermal difference between a lower…

Wind turbines to power telecommunication Systems: A case study in Sicily

2011

Off-line methods for determining air quality in museums

2010

This paper will examine three methodologies deployed in off-line research relating to air quality in museums. These methodologies made use of sensors based on the different chemical-physicalproperties of various materials (corrosiveness, hardness and absorption). Various field applications were applied to case studies, which were performed in two museums in Palermo, Italy: the Regional Gallery of Palazzo Abatellis and the Diocesan Museum. This review of methodologies and sensors examines which protocol should be put into practice in museums in monitoring the air quality of display spaces and the conservation of cultural artefacts.

A study of the acoustic parameters of ancient theaters

2013

Although many centuries have passed, in many ancient theatres evocative theatrical performances still take place, especially during summer. Greek and Latin architects care for equilibrium of proportions offers not only an intense quality of view but also a high quality acoustics. In our study we did an analysis both theoretical and experimental of the acoustic parameters of the ancient theaters of Syracuse, Segesta, and Akrai, in Sicily and the theater of Bulla Regia, in Jendouba (Tunisia), it was only simulated, because of the inability to reach the scene for reasons due to the political turmoil. A measurement session was carried out by our team in the framework of a wide research project …

Experimental Evidence on the Thermal Performance of Opaque Surfaces in Mediterranean Climate

2013

The thermal insulation of buildings, intended as wrap feature which determines the dispersion of heat, the reference parameter is necessary to contain the thermal losses during the winter season. The transmittance of the opaque components, used as an indicator of the energy quality of a casing, together with the overall coefficient of dispersion, represents a proper descriptor of the behavior during the heating season. However, if a strong insulation in winter conditions brings only positive effects, the same cannot be said for the summer conditions. A high value of the insulation in the casing is convenient only when the gains free, either in the form of solar contribution that of endogeno…