0000000001293578
AUTHOR
Pekka Tynjälä
Co-precipitation of Mg-doped Ni0.8Co0.1Mn0.1(OH)₂:effect of magnesium doping and washing on the battery cell performance
Co-precipitation of Ni0.8Co0.1Mn0.1(OH)2 (NCM811) and Mg-doped (0.25 wt% and 0.5 wt%) NCM811 precursors is carried out from concentrated metal sulphate solutions. In this paper, the aim is to study the role of magnesium dopant in the co-precipitation step of NCM811, the cathode active material and further the Li-ion battery cell performance. Based on the results, magnesium was fully co-precipitated in the NCM811 precursors, as expected from thermodynamic calculations. The presence of magnesium in these precursors was also confirmed by several characterization methods and magnesium was evenly distributed in the sample. It was observed that tapped density decreased and surface area increased …
Use of Calcined Dolomite as Chemical Precipitant in the Simultaneous Removal of Ammonium and Phosphate from Synthetic Wastewater and from Agricultural Sludge
Phosphorus as phosphate and nitrogen as ammonium or nitrate are the main nutrients in wastewaters and agricultural sludges. They runoff easily to waterways and cause eutrophication in water bodies. However, ammonium and phosphate could be precipitated simultaneously and used as recycled nutrients. In this research, dolomite calcined at 650 °
The use of calcined paper mill sludge as a chemical precipitant in the simultaneous removal of ammonium and phosphate : paper mill waste recycling and reuse
Currently, recycling and re-use of materials is extremely important due to the diminishing of natural resources. The objective of the European Union’s circular economy strategy is to increase recycling and the use of industrial waste materials and side streams as secondary raw materials. In this study, a chemical precipitation method to simultaneously remove ammonium nitrogen and phosphate from the liquid phase of anaerobic digestate using calcined paper mill sludge was studied. Papermill sludge is a waste material that forms in the paper-making process. In addition, commercial calcium oxide (CaO) was used as a reference precipitant. The suitability of the formed precipitate’s composition f…
Utilization of waste sodium sulfate from battery chemical production in neutral electrolytic pickling
Several industrial activities produce metal sulfates, which are controlled by strict limitations for wastewater concentrations of sulfate. One emerging area where these activities occur is the production of lithium-ion battery chemicals in which sodium sulfates are formed because of cathode precursor co-precipitation. Several solutions for sulfate removal exist, but one option is to reuse the sulfate side stream in other processes to increase circular economy and atom efficiency. In this paper, the reuse of sodium sulfate solution in a steel industry pickling solution is considered. Neutral electrolytic pickling experiments were carried out to compare the pickling behavior of the electrolyt…
Activated Carbon from Renewable Sources: Thermochemical Conversion and Activation of Biomass and Carbon Residues from Biomass Gasification
Activated carbon is one of the most widely applied adsorbent. As a porous carbon, it is used for the purification of both gaseous and liquid emissions. Activated carbon is prepared from fossil resources, such as coal, or from biomass through (hydro)thermal processing followed by chemical and/or physical activation. Further, some biomass thermal treatment processes, such as biomass gasification, produce carbon residues that can be modified to activated carbon with physical or chemical activation methods. The desired properties of activated carbon, i.e. high specific surface area and porosity, high carbon content and excellent sorption capacity, can be modified and optimized during thermochem…
Water leaching of roasted vanadium slag : Desiliconization and precipitation of ammonium vanadate from vanadium solution
This research investigated water leaching of roasted vanadium slag and studied the effects of leaching parameters, such as agitation speed, temperature, liquid-to-solid ratio, and leaching time. Further, solution purification via desiliconization and precipitation of ammonium vanadate were studied using the vanadium solution obtained from the water leaching of roasted vanadium slag. Vanadium solution contains residual silicon (1.67 g/L), which should be removed before ammonium vanadate precipitation. Based on the results, vanadium can be effectively recovered from vanadium slag and a recovery efficiency of 96.9% was obtained under optimal water leaching conditions. During solution purificat…
Sulphate removal over barium-modified blast-furnace-slag geopolymer
Blast-furnace slag and metakaolin were geopolymerised, modified with barium or treated with a combination of these methods in order to obtain an efficient SO4(2-) sorbent for mine water treatment. Of prepared materials, barium-modified blast-furnace slag geopolymer (Ba-BFS-GP) exhibited the highest SO4(2-) maximum sorption capacity (up to 119mgg(-1)) and it compared also favourably to materials reported in the literature. Therefore, Ba-BFS-GP was selected for further studies and the factors affecting to the sorption efficiency were assessed. Several isotherms were applied to describe the experimental results of Ba-BFS-GP and the Sips model showed the best fit. Kinetic studies showed that th…
The use of industrial waste materials for the simultaneous removal of ammonium nitrogen and phosphate from the anaerobic digestion reject water
The European Union’s circular economy strategy aims to increase the recycling and re-use of products and waste materials. According to the strategy, the use of industry waste materials and side flows is required to be more effective. In this research, a chemical precipitation method to simultaneously remove ammonium and phosphate from the reject water of anaerobic digestion plant using calcined paper mill sludge and fly ash as a precipitant, was tested. Paper mill sludge is a waste material formed in the paper-making process, and fly ash is another waste material formed in the power plant. Objective of this research was to test whether these industrial waste streams could be used as low cos…
Correlation of aluminum doping and lithiation temperature with electrochemical performance of LiNi1-xAlxO2 cathode material
Abstract This article presents a process for producing LiNi1-xAlxO2 (0 < × < 0.05) cathode material with high capacity and enhanced cycle properties of 145 mAh/g after 600 cycles. The LiNi1-xAlxO2 (0 < × < 0.05) cathode material is prepared by mixing coprecipitated Ni(OH)2 with LiOH and Al(OH)3, followed by lithiation at temperature range of 650–710 °C, after which any residual lithium from lithiation is washed from the particle surfaces. Electrochemical performance was studied within full-cell and half-cell application; in addition, different material characterization methods were carried out to explain structure changes when certain amount of aluminum is introduced in the …
The Use of Ca- and Mg-Rich Fly Ash as a Chemical Precipitant in the Simultaneous Removal of Nitrogen and Phosphorus - Recycling and Reuse
The European Union’s circular economy strategy aims to increase the recycling and re-use of products and waste materials. According to the strategy, the use of industry waste material should be more effective. A chemical precipitation method to simultaneously remove phosphorus and nitrogen from synthetic (NH4)2HPO4 solution and the liquid phase of anaerobic digestate using fly ash as a precipitant was tested. Fly ash is a waste material formed in the power plant process. It mainly contains calcium oxide (CaO) and magnesium oxide (MgO). Saturated precipitant solution was prepared from fly ash, which was added in small proportions to (NH4)2HPO4 solution during the experiment. Fly ash’s effect…
Sulphate removal over barium-modified blast-furnace-slag geopolymer
Blast-furnace slag and metakaolin were geopolymerised, modified with barium or treated with a combination of these methods in order to obtain an efficient SO42− sorbent for mine water treatment. Of prepared materials, barium-modified blast-furnace slag geopolymer (Ba-BFS-GP) exhibited the highest SO42− maximum sorption capacity (up to 119 mg g−1) and it compared also favourably to materials reported in the literature. Therefore, Ba-BFS-GP was selected for further studies and the factors affecting to the sorption efficiency were assessed. Several isotherms were applied to describe the experimental results of Ba-BFS-GP and the Sips model showed the best fit. Kinetic studies showed that the so…
Utilization of waste sodium sulfate from battery chemical production in neutral electrolytic pickling
Abstract Several industrial activities produce metal sulfates, which are controlled by strict limitations for wastewater concentrations of sulfate. One emerging area where these activities occur is the production of lithium-ion battery chemicals in which sodium sulfates are formed because of cathode precursor co-precipitation. Several solutions for sulfate removal exist, but one option is to reuse the sulfate side stream in other processes to increase circular economy and atom efficiency. In this paper, the reuse of sodium sulfate solution in a steel industry pickling solution is considered. Neutral electrolytic pickling experiments were carried out to compare the pickling behavior of the e…
Effects of Lithium Source and Content on the Properties of Li-Rich Layered Oxide Cathode Materials
Lithium-rich layered oxide (LLO) are considered high-capacity cathode materials for next-generation lithium-ion batteries. In this study, LLO cathode materials were synthesized via the hydroxide coprecipitation method followed by a two-step lithiation process using different lithium contents and lithium sources. The effects of lithium content and lithium source on structure and electrochemical performance were investigated. This study demonstrated the clear impact of Li/TM ratio on electrochemical performance. Lower Li/TM ratio reduced the irreversible capacity loss in the first cycle and provided better cycling stability among all samples. The best results exhibited an initial discharge ca…
H2-TPR, XPS and TEM Study of the Reduction of Ru and Re promoted Co/γ-Al2O3, Co/TiO2 and Co/SiC Catalysts
<p class="1Body">Effects of Ru and Re promoters on Co-CoO<sub>x </sub>catalysts supported on γ-Al<sub>2</sub>O<sub>3</sub>, TiO<sub>2</sub> and SiC were investigated to improve the understanding of the role of promoters of the active phase of Co-CoO<sub>x</sub>-Ru and Co-CoO<sub>x</sub>-Re. The influence of promoter addition on the composition and activity of the catalysts was characterized by several methods, such as H<sub>2</sub>-TPR, XPS, chemisorption and TEM. Furthermore, the role of support and metal-support interaction was especially studied and different support materials were compared.</p&g…
Utilisation of barium-modified analcime in sulphate removal: Isotherms, kinetics and thermodynamics studies
Abstract Analcime and commercial zeolite were employed as a precursor for preparing sorbent material for SO42− removal over barium modification. Three sorbents were prepared: barium-modified analcime (ANA-Na-Ba), barium-modified acid-washed analcime (ANA-Ac-Na-Ba) and barium-modified zeolite (ZSM5-Na-Ba). Of the prepared materials, ANA-Ac-Na-Ba was the most efficient sorbent material for SO42− removal, with a maximum sorption uptake of 13.7 mg g−1 at room temperature. Batch sorption experiments were performed to evaluate the effect of initial pH, initial SO42− concentration, sorbent dosage, temperature and contact time of sorption. Several isotherms were applied to describe the experimental…
Precipitation and Calcination of High-Capacity LiNiO2 Cathode Material for Lithium-Ion Batteries
This article presents the electrochemical results that can be achieved for pure LiNiO2 cathode material prepared with a simple, low-cost, and efficient process. The results clarify the roles of the process parameters, precipitation temperature, and lithiation temperature in the performance of high-quality LiNiO2 cathode material. Ni(OH)2 with a spherical morphology was precipitated at different temperatures and mixed with LiOH to synthesize the LiNiO2 cathode material. The LiNiO2 calcination temperature was optimized to achieve a high initial discharge capacity of 231.7 mAh/g (0.1 C/2.6 V) with a first cycle efficiency of 91.3% and retaining a capacity of 135 mAh/g after 400 cycles. These a…
Effect of Reaction Conditions on the Coprecipitation of Ni(OH)2 for Lithium-Ion Batteries
Electrochemical performance of cathode active materials (CAMs) is dependent on the properties of coprecipitated precursors (pCAMs). This is a sensitive process affected by several reaction parameters such as temperature, pH, concentration of reactants, agitation rate, and residence time. In this paper, the effect of parameters influencing the particle size growth and the physical properties, such as particle morphology and tapped density, was studied in the coprecipitation of Ni(OH)2. Formation of a homogeneous population with narrow particle size distribution was observed, followed by a more heterogeneous population of dense particles. Ammonia concentration and residence time had significa…