Search results for " sensor"
showing 10 items of 1714 documents
ALD thin ZnO layer as an active medium in a fiber-optic Fabry–Perot interferometer
2015
Abstract A novel optical fiber sensor of temperature using a thin ZnO layer fabricated by atomic layer deposition (ALD) is demonstrated for the first time. The thin ZnO layer was grown on the face of a standard optical telecommunication fiber SMF-28 and operates as a Fabry–Perot interferometer sensitive to temperature. The interferometer characterization was made in the temperature range extending from 50 to 300 °C with resolution equal to 1 °C. The output signal was analyzed by measurement of the shift of the maxima in spectral pattern. The sensitivity of temperature measurement is about 0.05 nm/°C. Furthermore, very good linearity of the sensor was achieved with correlation coefficient R2…
Measurement of UV-induced absorption and scattering losses in photosensitive fibers
2018
UV-assisted fabrication of gratings using photosensitive fibers is a well-established technique, based on the UV-induced permanent modification of the refractive index of the fiber material. As a result, the absorption coefficient is also changed. Here, we exploit the thermal sensitivity of whispering gallery mode resonances of the fiber itself to measure the profile of the heating along an irradiated fiber versus the input power and for different UV radiation intensities. Our technique allows discriminating between the absorption and scattering contributions to the overall losses, by comparing the results obtained with our technique with direct transmission measurements. Different photosen…
Photo-acoustic excitation and optical detection of fundamental flexural guided wave in coated bone phantoms.
2013
Abstract Photo-acoustic (PA) imaging was combined with skeletal quantitative ultrasound (QUS) for assessment of human long bones. This approach permitted low-frequency excitation and detection of ultrasound so as to efficiently receive the thickness-sensitive fundamental flexural guided wave (FFGW) through a coating of soft tissue. The method was tested on seven axisymmetric bone phantoms, whose 1- to 5-mm wall thickness and 16-mm diameter mimicked those of the human radius. Phantoms were made of a composite material and coated with a 2.5- to 7.5-mm layer of soft material that mimicked soft tissue. Ultrasound was excited with a pulsed Nd:YAG laser at 1064-nm wavelength and received on the s…
Assessment of the cortical bone thickness using ultrasonic guided waves: Modelling and in vitro study
2007
Determination of cortical bone thickness is warranted, e.g., for assessing the level of endosteal resorption in osteoporosis or other bone pathologies. We have shown previously that the velocity of the fundamental antisymmetric (or flexural) guided wave, measured for bone phantoms and bones in vitro, correlates with the cortical thickness significantly better than those by other axial ultrasound methods. In addition, we have introduced an inversion scheme based on guided wave theory, group velocity filtering and 2-D fast Fourier transform, for determination of cortical thickness from the measured velocity of guided waves. In this study, the method was validated for tubular structures by usi…
Determination of Bubble Size Distribution Using Ultrasound Array Imaging
2020
In this article, ultrasonic phased arrays are deployed as an imaging tool for industrial process analysis. Such arrays are typically used for sonar, medical diagnosis, and nondestructive testing; however, they have not yet been applied to industrial process analysis. The precise positioning of array elements and high frequencies possible with this technology mean that highly focused images can be generated, which cannot currently be achieved using ultrasound tomography. This article aims to highlight the potential of this technology for the measurement of bubble size distribution (BSD) and to demonstrate its application to both intrusive and noninvasive process measurements. Ultrasound imag…
Application of low intensity ultrasonics to cheese manufacturing processes.
2002
Ultrasound has been used to non-destructively assess the quality of many foods such as meat, fish, vegetables and dairy products. This paper addresses the applications of low intensity ultrasonics in the cheese manufacturing processes and highlights the areas where ultrasonics could be successfully implemented in the future. The decrease of ultrasonic attenuation during the renneting process can be used to determine the optimum cut time for cheese making. The ultrasonic velocity increases during maturation for those types of cheese that become harder during this manufacturing stage, thus being an indicator of the maturity degree. Moreover, ultrasonic measurements could be linked to sensory …
Defect characterization in Al welded joints by non-contact Lamb wave technique
2006
Abstract The use of air-coupled sensors to detect flaws in Al welded joints and the advantage of Lamb wave for their characterization has been proved. Ultrasonic waves were generated by a pulsed laser and by contact angle-beam transducer, and received by an air-coupled capacitive transducer. Laser-based configuration was used to quickly locate the defect, whereas the angle-beam contact probe configuration to characterize it thanks to the dispersive behavior of Lamb waves. Guided waves allow inspection of the complete thickness with only one scan, permitting to detect and to size both internal and surface defects; their high flexibility in the measurement is due to the various parameters cha…
Laser ultrasonics for defect evaluation on coated railway axles
2020
Abstract This scientific paper focuses on the application of an advanced non-destructive technique for an effective inspection of railway axles. The method pertains to ultrasonic techniques, which are widely used in the railway field. The experimental investigation was carried out on simulated defects tooled near the cross section reduction of the axle, in order to simulate fatigue cracks which, due to notch effect, can trigger crack propagation and axle failure. The aim of this research activity is to evaluate how efficiently the proposed technique detects defects and to verify its applicability to axles with a black coating for protection. In view of the experimental setup, comprising a p…
Theoretical and experimental contributions on ultrasonic contactless examination of underground pipes through which pressurized fluids circulate
2019
Abstract In any civil or industrial construction, there are many embedded pipelines through which pressurized fluids or gases are circulate and which, over time, are subject to corrosion. Examination and monitoring of corrosion/erosion process in order to determine the service life of pipelines through which fluids circulate at different temperatures and / or pressures is a particularly important task for both the designer and the owner because knowledge of “health status” of these in time is extremely. On-site ultrasound control of wall thickness is based on simple propagation time measurements and is typically used to evaluate corrosion and erosion. The paper presents a non-destructive co…
Benzene monitoring by micro-machined sensors with SnO2 layer obtained by using micro-droplet deposition technique
2011
International audience; SnO2 thin layers were deposited by the way of the micro-droplet technique. The sensor substrate consisted of a thin membrane developed on oxidised silicon wafer. The sensing layers were deposited by means of the micro-droplet technique into thin layers of about 100 nm. Such devices were tested for benzene detection. The obtained results showed a very high sensitivity for this chemical compound since 500 ppb were detected. The results presented in this paper were not focused on the reactional mechanism of benzene detection but rather on the development of a cheap and sensitive sensor using sol-gel and micro-droplet processes. Since these layers were elaborated using s…