Search results for "Computer-assisted"
showing 10 items of 1186 documents
Effects of endodontic treatment on apparent Young’s modulus of human teeth: in vitro study using speckle interferometry
2012
The introduction of new techniques for endodontic procedures requires the analysis of the biomechanical behavior of dental structures. Digital speckle shearing pattern interferometry (DSSPI) is a nondestructive optical measuring technique that allows one to directly quantify deformations in teeth that are subjected to stress. DSSPI technique was applied to measure small deformations caused by flexion in different types of teeth. The test was carried out both before and after endodontic treatment with the ProTaper method in order to evaluate the variation of dental elasticity, taking into the account the type of tooth and the endodontic treatment. The results obtained show that dental elasti…
Study of smartphone suitability for mapping of skin chromophores.
2015
RGB (red-green-blue) technique for mapping skin chromophores by smartphones is proposed and studied. Three smartphones of different manufacturers were tested on skin phantoms and in vivo on benign skin lesions using a specially designed light source for illumination. Hemoglobin and melanin indices obtained by these smartphones showed differences in both tests. In vitro tests showed an increment of hemoglobin and melanin indices with the concentration of chromophores in phantoms. In vivo tests indicated higher hemoglobin index in hemangiomas than in nevi and healthy skin, and nevi showed higher melanin index compared to the healthy skin. Smartphones that allow switching off the automatic cam…
The Use of Atomic Force Microscopy in Determining the Stiffness and Adhesion Force of Human Dentin After Exposure to Bleaching Agents
2009
Introduction: Oxidant bleaching agents may induce several alterations on mineralized teeth tissues. Our aim is to study,at the ultrastructurallevel,mechanicalmodifications induced on dentin after exposure to different bleaching agents.Methods: Nanoindentation performed with atomic force microscopy was used to measure changes in dentin stiffness as well as the adhesion force between the tip and the tissue both in intertubular and peritubulardentin.Foreachspecimen,dentinlocalization, and bleaching agent, 100 independent nanoindentations were performed. Carbamide peroxide (30%) and hydrogenperoxide(35%) wereusedasbleaching agents. Results: A significant reduction of both stiffness and adhesion…
Response charactterization of ammonium tartrate solid state pellets for ESR dosimetry with radiotherapeutic photon and electron beams.
2001
Solid state pellets (1 mm thick) for electron spin resonance (ESR) dosimetry were made using ammonium tartrate as the radiation-sensitive substance. Their behaviour was experimentally investigated as a function of dose with 60Co gamma rays. The calibration function obtained permits measurements of absorbed dose in the 2-50 Gy range, with a combined uncertainty of +/-4%. The lowest detectable dose was about 0.5 Gy. These properties are comparable with or even better than those of ESR dosimeters made from other materials. The time stability of the ESR signal of ammonium tartrate dosimeters at different storage conditions after irradiation was studied. A rather complex behaviour was observed, …
Imaging of laser-excited tissue autofluorescence bleaching rates.
2009
Experimental methodology for imaging of laser-excited tissue autofluorescence bleaching rates has been developed and clinically tested. The fluorescence images were periodically captured from the same tissue area over a certain time, with subsequent detection of the fluorescence intensity decrease rate at each image pixel and further imaging the planar distribution of those values. Spectral features at each image pixel were analyzed with a hyperspectral imaging camera. Details of the equipment and image processing are described as well as some measurement results that confirm the feasibility of the proposed technology.
A Monte Carlo study of intersource effects in dome-type applicators loaded with LDR Cs-137 sources
2005
In this study, the dose rate distributions produced by low dose rate Cs-137 sources loaded in afterloadable dome applicators are studied using the Monte Carlo method. Dose differences between Monte Carlo results and calculations done using the superposition principle are within 1-3% in front of the applicator and between 3 and 10% near and along the longitudinal source axis. Consequently, the real doses to lateral vaginal wall, rectum and bladder are very close to the doses estimated applying the superposition principle, while the dose to the vaginal cuff has been overestimated by up to 10%.
0.48Tb/s (12x40Gb/s) WDM transmission and high-quality thermo-optic switching in dielectric loaded plasmonics
2012
We demonstrate Wavelength Division Multiplexed (WDM)-enabled transmission of 480Gb/s aggregate data traffic (12x40Gb/s) as well as high-quality 1x2 thermo-optic tuning in Dielectric-Loaded Surface Plasmon Polariton Waveguides (DLSPPWs). The WDM transmission characteristics have been verified through BER measurements by exploiting the heterointegration of a 60 mu m-long straight DLSPPW on a Silicon-on-Insulator waveguide platform, showing error-free performance for six out of the twelve channels. High-quality thermo-optic tuning has been achieved by utilizing Cycloaliphatic-Acrylate-Polymer as an efficient thermo-optic polymer loading employed in a dual-resonator DLSPPW switching structure, …
Subtractive imaging in confocal scanning microscopy using a CCD camera as a detector
2012
[EN] We report a scheme for the detector system of confocal microscopes in which the pinhole and a large-area detector are substituted by a CCD camera. The numerical integration of the intensities acquired by the active pixels emulates the signal passing through the pinhole. We demonstrate the imaging capability and the optical sectioning of the system. Subtractive-imaging confocal microscopy can be implemented in a simple manner, providing superresolution and improving optical sectioning. (C) 2012 Optical Society of America
A monte carlo study of dose rate distribution around the specially asymmetric CSM3-a 137Cs source.
2001
The CSM3 137Cs type stainless-steel encapsulated source is widely used in manually afterloaded low dose rate brachytherapy. A specially asymmetric source, CSM3-a, has been designed by CIS Bio International (France) substituting the eyelet side seed with an inactive material in the CSM3 source. This modification has been done in order to allow a uniform dose level over the upper vaginal surface when this `linear' source is inserted at the top of the dome vaginal applicators. In this study the Monte Carlo GEANT3 simulation code, incorporating the source geometry in detail, was used to investigate the dosimetric characteristics of this special CSM3-a 137Cs brachytherapy source. The absolute do…
Femtosecond digital lensless holographic microscopy to image biological samples
2013
The use of femtosecond laser radiation in digital lensless holographic microscopy (DLHM) to image biological samples is presented. A mode-locked Ti:Sa laser that emits ultrashort pulses of 12 fs intensity FWHM, with 800 nm mean wavelength, at 75 MHz repetition rate is used as a light source. For comparison purposes, the light from a light-emitting diode is also used. A section of the head of a drosophila melanogaster fly is studied with both light sources. The experimental results show very different effects of the pinhole size on the spatial resolution with DLHM. Unaware phenomena on the field of the DLHM are analyzed.