Search results for "EDC"
showing 10 items of 134 documents
EMI Filter Re-Design in a SMPS with Inductor in Saturation
2021
This paper analyzes the design issues of the input EMI (Electro-Magnetic Interference) filter's in a switching mode power supply where the power inductor is operated in saturation. Starting with a SMPS equipped with linear inductor, the input filter is firstly designed to comply with Standards. Then, a new inductor with a smaller core size is employed in the same SMPS to exploit saturation. The EMI filter is re-designed, taking into account the increase of EMI introduced by the non-linear operation of the inductor. Finally, the reduction of the inductor's size and cost is compared with the increased size and cost of the EMI filter.
Layout influence on microwave performance of graphene field effect transistors
2018
The authors report on an in-depth statistical and parametrical investigation on the microwave performance of graphene FETs on sapphire substrate. The devices differ for the gate-drain/source distance and for the gate length, having kept instead the gate width constant. Microwave S -parameters have been measured for the different devices. Their results demonstrate that the cut-off frequency does not monotonically increase with the scaling of the device geometry and that it exists an optimal region in the gate-drain/source and gate-length space which maximises the microwave performance.
Terahertz electrical writing speed in an antiferromagnetic memory
2018
The speed of writing of state-of-the-art ferromagnetic memories is physically limited by an intrinsic gigahertz threshold. Recently, realization of memory devices based on antiferromagnets, in which spin directions periodically alternate from one atomic lattice site to the next has moved research in an alternative direction. We experimentally demonstrate at room temperature that the speed of reversible electrical writing in a memory device can be scaled up to terahertz using an antiferromagnet. A current-induced spin-torque mechanism is responsible for the switching in our memory devices throughout the 12-order-of-magnitude range of writing speeds from hertz to terahertz. Our work opens the…
A Compact SPICE Model for Organic TFTs and Applications to Logic Circuit Design
2016
This work introduces a compact DC model developed for organic thin film transistors (OTFTs) and its SPICE implementation. The model relies on a modified version of the gradual channel approximation that takes into account the contact effects, occurring at nonohmic metal/organic semiconductor junctions, modeling them as reverse biased Schottky diodes. The model also comprises channel length modulation and scalability of drain current with respect to channel length. To show the suitability of the model, we used it to design an inverter and a ring oscillator circuit. Furthermore, an experimental validation of the OTFTs has been done at the level of the single device as well as with a discrete-…
Implementation of compact VLSI FitzHugh-Nagumo neurons
2008
In this paper we show a low power and very compact VLSI implementation of a FitzHugh-Nagumo neuron for large network implementations. The circuit consists of only 17 small transistors and two capacitors and consumes less than 23 muW. It is composed of a nonlinear resistor and a lossy active inductor. We demonstrate that a simple low Q active inductor can be used instead of a complex one because the parasitic series resistor can be easily embedded to the FitzHugh-Nagumo model. We also perform a statistical analysis to check the robustness of the circuit against mismatch.
Realistic model of compact VLSI FitzHugh–Nagumo oscillators
2013
In this article, we present a compact analogue VLSI implementation of the FitzHugh–Nagumo neuron model, intended to model large-scale, biologically plausible, oscillator networks. As the model requires a series resistor and a parallel capacitor with the inductor, which is the most complex part of the design, it is possible to greatly simplify the active inductor implementation compared to other implementations of this device as typically found in filters by allowing appreciable, but well modelled, nonidealities. We model and obtain the parameters of the inductor nonideal model as an inductance in series with a parasitic resistor and a second order low-pass filter with a large cut-off freque…
Fault Emulation for Dependability Evaluation of VLSI Systems
2008
Advances in semiconductor technologies are greatly increasing the likelihood of fault occurrence in deep-submicrometer manufactured VLSI systems. The dependability assessment of VLSI critical systems is a hot topic that requires further research. Field-programmable gate arrays (FPGAs) have been recently pro posed as a means for speeding-up the fault injection process in VLSI systems models (fault emulation) and for reducing the cost of fixing any error due to their applicability in the first steps of the development cycle. However, only a reduced set of fault models, mainly stuck-at and bit-flip, have been considered in fault emulation approaches. This paper describes the procedures to inje…
Hybrid VLC/WiFi Architectures with Priority Feedback Channels
2022
In this paper, we consider integrating Visible Light Communication (VLC) and WiFi technologies in an ultra-dense (massive) Internet of Things scenario, where WiFi links are used for complementing VLC links and vice-versa. Indeed, in case of mobility and/or bidirectional communications, limited coverage areas and self-generated interference can be an issue. We consider hybrid VLC/WiFi nodes where the VLC link is used for the majority of (data) traffic and the WiFi link is employed as a feedback channel (e.g. transmitting TCP ACKs). In presence of intense WiFi traffic, the WiFi network may be congested and thus, to fully exploit the VLC bandwidth, we discuss possible priority mechanisms to fu…
Critical Influence of Dielectric Sensitive Material and Manufactured Process in Microwave Gas-Sensing: Application of Ammonia Detection with an Inter…
2020
In this paper, authors propose a study on microwave gas sensors and the influence of critical key parameters such as the sensitive material and the circuit conception process. This work aims to determine the influence of these parameters on the quality of the final response of the microwave gas sensor. The fixed geometry of the sensor is a microstrip interdigital capacitor coated with a sensitive layer excited with two 50 Ω SMA ports. The sensitive material has been chosen in order to interact with the target gas: ammonia. Indeed, this gas interacts with phthalocyanine and metal oxides like hematite, TiO2. To explore the effect of the circuit manufacturing process, three series of samples a…
Design and Characterization of Automated Color Sensors System
2014
International audience; The paper presents a color sensor system that can process light reflected from a surface and produce a digital output representing the color of the surface. The end-user interface circuit requires only a 3-bit pseudo flash analog-to-digital converter (ADC) in place of the conventional/typical design comprising ADC, digital signal processor and memory. For scalability and compactness, the ADC was designed such that only two comparators were required regardless of the number of color/wavelength to be identified. The complete system design has been implemented in hardware (bread board) and fully characterized. The ADC achieved less than 0.1 LSB for both INL and DNL. The…