Search results for "Elastic recoil"
showing 10 items of 43 documents
Influence of titanium-substrate roughness on Ca–P–O thin films grown by atomic layer deposition
2013
Abstract Amorphous Ca–P–O films were deposited on titanium substrates using atomic layer deposition, while maintaining a uniform Ca/P pulsing ratio of 6/1 with varying number of atomic layer deposition cycles starting from 10 up to 208. Prior to film deposition the titanium substrates were mechanically abraded using SiC abrasive paper of 600, 1200, 2000 grit size and polished with 3 μm diamond paste to obtain surface roughness R rms values of 0.31 μm, 0.26 μm, 0.16 μm, and 0.10 μm, respectively. The composition and film thickness of as-deposited amorphous films were studied using Time-Of-Flight Elastic Recoil Detection Analysis. The results showed that uniform films could be deposited on ro…
Nucleation and growth of ZnO on PMMA by low-temperature atomic layer deposition
2015
ZnO films were grown by atomic layer deposition at 35 °C on poly(methyl methacrylate) substrates using diethylzinc and water precursors. The film growth, morphology, and crystallinity were studied using Rutherford backscattering spectrometry, time-of-flight elastic recoil detection analysis, atomic force microscopy, scanning electron microscopy, and x-ray diffraction. The uniform film growth was reached after several hundreds of deposition cycles, preceded by the precursor penetration into the porous bulk and island-type growth. After the full surface coverage, the ZnO films were stoichiometric, and consisted of large grains (diameter 30 nm) with a film surface roughness up to 6 nm (RMS). T…
Aluminum oxide from trimethylaluminum and water by atomic layer deposition:The temperature dependence of residual stress, elastic modulus, hardness a…
2014
Use of atomic layer deposition (ALD) in microelectromechanical systems (MEMS) has increased as ALD enables conformal growth on 3-dimensional structures at relatively low temperatures. For MEMS device design and fabrication, the understanding of stress and mechanical properties such as elastic modulus, hardness and adhesion of thin film is crucial. In this work a comprehensive characterization of the stress, elastic modulus, hardness and adhesion of ALD aluminum oxide (Al2O3) films grown at 110-300 C from trimethylaluminum and water is presented. Film stress was analyzed by wafer curvature measurements, elastic modulus by nanoindentation and surface-acoustic wave measurements, hardness by na…
Ion-sputtering deposition of Ca–P–O films for microscopic imaging of osteoblast cells
2007
Abstract An ion-beam sputtering technique was used to produce Ca–P–O films on borosilicate glass at room temperature from hydroxyapatite targets using nitrogen, argon and krypton beams at different acceleration voltages. The sputtering target was pressed from high purity hydroxyapatite powder or mixture of high purity hydroxyapatite powder and red phosphorus in order to optimise the film composition. The film composition, determined using time-of-flight elastic recoil detection analysis (TOF–ERDA), was found to be strongly dependent on the ion energy used for deposition. By extra doping of the target with P the correct Ca/P atomic ratio in the deposited films was reached. The films deposite…
A study of solar thermal absorber stack based on CrAlSiNx/CrAlSiNxOy structure by ion beams
2019
Renewable energies are foreseen as a major energy resource for next generations. Among several energy sources and technologies available, Concentrated Solar Power (CSP) technology has a great potential, but it needs to be optimised, in particular to reduce the costs, with an increase of the operating temperature and long term stability. This goal can be achieved by tailoring the composition and multilayer structure of films. In this work we present and discuss the results obtained from solar absorber coatings based on nitride/oxynitride structures. A four-layer film structure, W/CrAlSiNx(HA)/CrAlSiNxOy(LA)/SiAlOx, was deposited on stainless steel substrates using magnetron sputtering deposi…
Characterization of ALD grown Ti x Al y N and Ti x Al y C thin films
2017
Abstract Atomic layer deposition (ALD) was used to grow Ti x Al y N and Ti x Al y C thin films using trimethylaluminum (TMA), titanium tetrachloride and ammonia as precursors. Deposition temperature was varied between 325 °C and 500 °C. Films were also annealed in vacuum and N 2 -atmosphere at 600–1000 °C. Wide range of characterization methods was used including time-of-flight elastic recoil detection analysis (ToF-ERDA), X-ray diffractometry (XRD), X-ray reflectometry (XRR), Raman spectroscopy, ellipsometry, helium ion microscopy (HIM), atomic force microscopy (AFM) and 4-point probe measurement for resistivity. Deposited films were roughly 100 nm thick and contained mainly desired elemen…
Ordering effects in extreme high-resolution depth profiling with MeV ion beams
2012
Abstract The continuing development of depth profiling with MeV ion beam methods with depth resolutions in the nanometre, and even sub-nanometre, regime implies the resolved depth become comparable with the interatomic spacing. To investigate how short-range ordering influences depth profiles at these resolutions, we have employed a mathematical modelling approach. The radial, g ( r ) and depth distribution, g ( z ) functions were calculated for (1 0 0) surface, random and amorphous Si structures at 300 K produced using molecular dynamics simulations with the EDIP quasi-empirical potential. The results showed that short-range ordering lead to reduction of the scattering yield below the deep…
Low-energy heavy-ion TOF-ERDA setup for quantitative depth profiling of thin films
2008
Abstract Low-energy heavy-ion time-of-flight elastic recoil detection analysis (TOF-ERDA) is becoming a mature technique for accurate characterization of thin films. In combination with a small tandem accelerator (∼2 MV terminal voltage) and beam energies below 20 MeV, it is suitable for routine analysis of key materials in semiconductor technology. In this paper we discuss advantages and drawbacks of low-energy ERDA, compared to high-energy ERDA, in terms of depth and mass resolution, detection efficiency for light elements, sample irradiation damage and quantification accuracy. The results presented are obtained with the time-of-flight telescope recently developed at IMEC. The time-of-fli…
Time-of-flight ERD with a 200mm2 Si3N4 window gas ionization chamber energy detector
2014
Abstract Low energy heavy ion elastic recoil detection work has been carried out in Jyvaskyla since 2009 using home made timing detectors, a silicon energy detector and a timestamping data acquisition setup forming a time-of-flight–energy telescope. In order to improve the mass resolution of the setup a new energy detector was designed to replace the silicon solid state detector, which suffered from radiation damage and had poor resolution for heavy recoils. In this paper the construction and operation of an isobutane filled gas ionization chamber with a 14 × 14 mm 2 100 nm thick silicon nitride window are described. In addition to greatly improved energy resolution for heavy ions, the dete…
Depth resolution optimization for low-energy ERDA
2007
Abstract With the implementation of low-energy time-of-flight Elastic Recoil Detection Analysis (ERDA), routine analysis of thin films with high depth resolution becomes possible. The optimization of the measurement conditions is a key issue for an accurate sample characterization and is normally a compromise among depth resolution, mass resolution and sensitivity, for a given sample. In this work, we focus on the depth resolution optimization, presenting an extensive study of two different materials, SiO 2 and TiN, representative of light and medium mass targets. The film thickness varies between 10 and 50 nm. The samples were measured with different beams ( 35 Cl, 63 Cu, 79 Br and 127 I),…