Search results for "Grain boundary"
showing 10 items of 143 documents
Investigation of TiO<sub>2</sub> Ceramic Surface Conductivity Using Conductive Atomic Force Microscopy
2012
Dense TiO2 (rutile) ceramic samples were prepared by sintering compacts of titanium dioxide anatase powder at 1500 °C for 5h. Sintered samples were polished and annealed in vacuum at 1000 °C for 1h. Structural properties of the samples were studied by X-ray diffraction, polarized light and scanning electron microscopy. The surface topography and local electrical conductivity of the samples were investigated by atomic force microscopy technique under atmospheric conditions. Enhanced electrical conductivity was observed at grain boundaries while the polished, vacuum annealed grains surface showed non-homogeneous conductivity.
TiO2 nanostructures prepared by ferrocene/cobalt catalyst agents
2008
We present the growth and characterization of TiO2 nanocrystals. Nanostructured growth is obtained in a low-pressure CVD system by using an organometallic precursor Ti(OC3H7)4 as both the Ti and O source catalyzed by both ferrocene (an organometallic precursor) and cobalt metallic clusters prepared by the microwave-assisted polyol method. Two kinds of TiO2 structures were obtained in the cobalt clusters: a) pine-tree like (with short-leaf structure) and b) long-leaf structures as large as a few micrometers in size and both under 10 nm in thickness. Long-leaf TiO2 structures were grown at cobalt grain boundaries. For the growth conditions utilized, the TiO2 structures are composed of both an…
Initial chemical transport of reducing elements and chemical reactions in oxide cathode base metal
2002
Abstract In the present work, the formation of compounds associated to the diffusion of reducing elements (Mg and Al) to the nickel surface of a one-piece oxide cathode has been studied. Those compounds have been evidenced after the annealing steps at high temperature performed on cathode base metal prior to the emitting coating deposition. Therefore, they form the “initial” interface between the nickel and the coating, in other words, the interface existing at the beginning of cathode life. Extensive analysis to characterize the nickel base prior to coating deposition has been performed by means of scanning electron microscopy (SEM) coupled with energy dispersive X-ray spectroscopy (EDX), …
Understanding sigma-phase precipitation in a stabilized austenitic stainless steel (316Nb) through complementary CALPHAD-based and experimental inves…
2014
Abstract Sigma-phase precipitation in a 316Nb “stabilized” austenitic stainless steel was studied through complementary CALPHAD-based and dedicated experimental investigations. Thermokinetic calculations performed using Thermo-Calc (with the DICTRA module) and MatCalc software showed that the sigma phase (σ) precipitated directly at γ-austenite grain boundaries (GB) via a common solid-state reaction when carbon and nitrogen contents fell below a critical threshold. Residual δ ferrite was found to be more susceptible to σ-phase precipitation; this type of precipitation occurred via two mechanisms that depended on the concentration profiles of δ-ferrite stabilizing elements induced by previou…
Monte Carlo Simulations of Surfaces and Interfaces in Materials
1996
Many applications of materials are controlled by their surface and interface properties. In particular, metallic alloys (but also mixed dielectric materials and amorphous polymer blends) are not homogeneously mixed on a microscopic length scale, although they are macroscopically homogeneous. Depending on the preparation of the sample, there exists a heterophase microstructure, with typical domain sizes, e.g. in the 1 to 102 µm range, separated by interfaces between them. The physical properties of such intrinsic interfaces (grain boundaries between small crystallites, antiphase domain boundaries in ordered alloys, Bloch walls in magnetic materials, etc.) are not only an important controllin…
Microstructure and mechanical effects of spark plasma sintering in alumina monolithic ceramics
2013
The specific effects of spark plasma sintering (SPS) on the creep behavior, microstructure and mechanical properties of alumina monolithic ceramic were investigated. SPS introduces strains that concentrate at grain boundaries and inhibit crack growth, resulting in an improvement in the flexural strength and fracture toughness. However, creep blocks grain boundary movements and decreases the reliability of the material. These strains can be removed by a post-sintering thermal treatment, which plays an important role in the distribution of dislocations.
First-principles study of nitrogen doping in cubic and amorphous Ge2Sb2Te5
2011
We investigated the structural, electronic and vibrational properties of amorphous and cubic Ge(2)Sb(2)Te(5) doped with N at 4.2 at.% by means of large scale ab initio simulations. Nitrogen can be incorporated in molecular form in both the crystalline and amorphous phases at a moderate energy cost. In contrast, insertion of N in the atomic form is very energetically costly in the crystalline phase, though it is still possible in the amorphous phase. These results support the suggestion that N segregates at the grain boundaries during the crystallization of the amorphous phase, resulting in a reduction in size of the crystalline grains and an increased crystallization temperature.
On-Surface Synthesis of Unsaturated Carbon Nanostructures with Regularly Fused Pentagon–Heptagon Pairs
2020
Multiple fused pentagon-heptagon pairs are frequently found as defects at the grain boundaries of the hexagonal graphene lattice and are suggested to have a fundamental influence on graphene-related materials. However, the construction of sp2-carbon skeletons with multiple regularly fused pentagon-heptagon pairs is challenging. In this work, we found that the pentagon-heptagon skeleton of azulene was rearranged during the thermal reaction of an azulene-incorporated organometallic polymer on Au(111). The resulting sp2-carbon frameworks were characterized by high-resolution scanning probe microscopy techniques and feature novel polycyclic architectures composed of multiple regularly fused pen…
P-T path development derived from shearband boudin microstructure
2016
This work focuses on the development of a regional P-T-path from the Malpica-Lamego Ductile Shear Zone, NW Portugal, based on the microstructures of shearband boudins evolved during progressive simple shear. The combination of microstructural analysis, fluid inclusion studies, crystallographic pre- ffered orientation and fractal geometry analyses, allows to link several stages in the internal evolution of the boudin to regional P-T conditions. The boudinage process is initiated under differential stress after the original layer achieved sufficient viscosity contrast relative to the surrounding matrix. Two main transformations occur simultaneously: i) change in the external shape with contin…
Use of Ultrasound in Reconditioning by Welding of Tools Used in the Process of Regenerating Rubber
2018
Addressing the problem of reconditioning large parts is of particular importance, due to their value and to the fact that the technologies for their reconditioning are very complex. The tools used to refine regenerated rubber which measure 660 mm in diameter and 2130 mm in length suffer from a rather fast dimensional wear. Within this research, the authors looked for a welding reconditioning procedure that would allow a very good adhesion between the deposited material layer and the base material. In this regard, the MAG (Metal Active Gas) welding process was used, but the ultrasonic activation of the welding process was also considered. Thus, the wire used for welding was activated conside…