Search results for "Instrumentation"
showing 10 items of 4914 documents
Ultra-low density metallic foams synthesized by contact glow discharge electrolysis (CGDE) for laser experiments★
2018
International audience; The goal of this work is to realize metallic foams synthesized by contact glow discharge electrolysis with specific characteristics. In this paper, we show the results of our studies, consisting in investigating parameters that influence the foams characteristics. Thus, the morphology of metallic foams is examined through scanning electron microscopy (SEM) observations with the acid nature. Moreover, the evolution of the mass and the volume of metallic foams with two experimental parameters (overvoltage and gold concentration) is also investigated. The acid nature affects the foams microscopic structure highlighted by the SEM observations, but for now no valid explan…
Composition-related structural, thermal and mechanical properties of Ba1−xSrxTiO3ceramics (0 ≤x≤ 0.4)
2015
The Ba1−xSrxTiO3 (BST) ceramics were prepared by conventional ceramic method. The crystalline structure and morphology were studied by X-ray diffraction and scanning electron microscopy, respectively. Experimental results show that increase of sintering temperature leads to an uncontrolled precipitating of the phase with a lower content of Ti. The dielectric constant and specific heat as a function of composition and temperature were investigated. The increasing concentration of Sr ions leads to a shift of the Curie point below room temperature. To determine the elastic constants (the Young's modulus E, the shear modulus G and the Poisson's ratio v) of BST, a method of measurement of the lo…
UV-Laser Plasma Study of Elemental Distributions of Paper Coatings
1995
The potential of a laser-generated plasma method in the analysis of coating coverage, coatweight distribution, and 3D distribution of various pigments of paper coating is described. A XeCl-excimer laser (308 nm) was used to generate microscopic plasma from the paper coating, and delayed detection of silicon and calcium atomic emission line intensities was used as a measure of mass vaporized. Macroscopic areas typically 10 × 10 mm2 at a spatial resolution of 250 μm were studied. With a single laser pulse (0.2 mJ of energy), about 2 ng of coating from a volume of 30 μm in diameter and 2 μm in depth was vaporized. The method seems to be useful for characterization of multilayer coatings.
Detection and quantification of lung cancer biomarkers by a micro-analytical device using a single metal oxide-based gas sensor
2018
International audience; The analysis of exhaled volatile organic compounds (VOCs) related to lung cancer is a very promising wayin medical diagnosis because it is non-invasive and much less expensive than traditional medical analysisused so far. In that sense, a silicon micro-analytical platform consisting of a micro-preconcentrator cou-pled to a silicon spiral gas chromatographic micro-column was built, and a metal oxide-based gas sensorwas used as a miniaturized gas detector. This micro-fabricated device was successfully tested to selec-tively detect low concentrations of VOCs considered as lung cancer biomarkers, within a few minuteseven in presence of high concentrations of water vapor …
Characterization of SiPM properties at liquid nitrogen temperature
2016
SiPM operation at cryogenic temperatures fails for many common devices. A particular type with deep channels in the silicon substrate instead of quenching resistors was thoroughly characterized from room temperature down to liquid nitrogen temperature by illuminating it with low light levels. The devices were mounted in vacuum with the temperature stabilized to allow long-term operation. SiPM signals from a LED pulser were acquired with single-pixel resolution. Generalized fits to the charge collection spectra were used to extract properties like single-pixel gain, inter-pixel variation, breakdown voltage, and photon detection efficiency. With these measurements a deeper investigation of th…
Alumina particle reinforced TiO2 composite films grown by direct liquid injection MOCVD
2014
Abstract The use of a liquid injection delivery system to form composite films containing nanoparticles was investigated. Al 2 O 3 –TiO 2 films were grown on silicon substrates by direct liquid injection MOCVD (DLI-MOCVD) at 400 °C. The α-Al 2 O 3 nanoparticles (α-Al 2 O 3 NPs) dispersed in TiO 2 films resulted from co-deposition using colloidal α-Al 2 O 3 solution and titanium tetraisopropoxide as titanium precursor. Scanning electron microscopy coupled with EDS as well as Raman spectroscopy confirmed the presence of α-Al 2 O 3 NPs aggregates embedded in the TiO 2 matrix. The liquid injection system coupled with CVD technique can be promising to form composite films containing preformed na…
Silicon resonator sensors: interrogation techniques and characteristics
1988
Interferometric and noninterferometric optical-fibre sensing systems for resonator vibrations are described. The quality factor variation with pressure, the temperature dependence of resonant frequency and the acceleration sensitivity are given for a double-ended tuning-fork based acceleratometer.
Glassy PEEK‐WC vs Rubbery Pebax®1657 Polymers: Effect on the Gas Transport in CuNi‐MOF Based Mixed Matrix Membranes
2020
Mixed matrix membranes (MMMs) are seen as promising candidates to overcome the fundamental limit of polymeric membranes, known as the so-called Robeson upper bound, which defines the best compromise between permeability and selectivity of neat polymeric membranes. To overcome this limit, the permeability of the filler particles in the MMM must be carefully matched with that of the polymer matrix. The present work shows that it is not sufficient to match only the permeability of the polymer and the dispersed phase, but that one should consider also the individual contributions of the diffusivity and the solubility of the gas in both components. Here we compare the gas transport performance o…
Quantification of low levels of amorphous content in maltitol
2004
A method for the quantification of low levels of amorphous content of maltitol with hyper-DSC (high speed DSC) was developed. The method is based on the fact that the change of specific heat ( � Cp) at the glass transition is linearly proportional to the amorphous content. Twelve synthetic mixtures with various degrees of crystalline and amorphous maltitol were prepared. � Cp was determined at both fictive and
High Resolution X-Ray Spectroscopy with Compound Semiconductor Detectors and Digital Pulse Processing Systems
2012
The advent of semiconductor detectors has revolutionized the broad field of X-ray spectroscopy. Semiconductor detectors, originally developed for particle physics, are now widely used for X-ray spectroscopy in a large variety of fields, as X-ray fluorescence analysis, X-ray astronomy and diagnostic medicine. The success of semiconductor detectors is due to several unique properties that are not available with other types of detectors: the excellent energy resolution, the high detection efficiency and the possibility of development of compact detection systems. Among the semiconductors, silicon (Si) detectors are the key detectors in the soft X-ray band (15 keV) and will continue to be the c…